Parts for Frigidaire FPCF3091LFD: 03 - Backguard Parts

This electronic control board manages the appliance's user interface and core functions, restoring reliable cycle control and display response when the original board fails. Replacing a faulty board can stop erratic operation and restore normal controls. What it does:

• Interprets user commands and runs programmed cycles for the appliance
• Sends signals to heaters, fans, valves, and motors to coordinate operation
• Common symptom: unresponsive or flashing display and failed cycle starts
• Common symptom: appliance runs erratically or stops mid-cycle

• Power off and disconnect the appliance before starting any work
• Handle the board by its edges and avoid contact with circuitry to prevent static damage
• Follow OEM service manual instructions for removal, connector placements, and grounding

This snap-in plug seals a small cabinet or component opening to keep out moisture, debris and pests while preserving a finished appearance. It's a simple, low-cost replacement that restores proper sealing and fit. What it does

• Seals unused holes or access openings to prevent water, dust and pests from entering
• Restores a finished look where trim or panels have a missing cap
• Helps stop rattles from loose openings and reduces airflow where needed
• Works as a direct-fit replacement when the original plug is damaged or lost

• One snap-in plug

• Remove surrounding trim or panel per your model's service instructions to access the opening
• Press the plug into the hole until it snaps fully into place; no special tools normally required
• Always disconnect power to the appliance before doing any service that requires panel removal

This is a replacement mounting screw used to secure the appliance power/control board, restoring a solid electrical board connection and preventing vibration or loose contacts. Ideal for repairs where the original screw is missing or damaged. What it does:

• Fastens the power/control board to the appliance chassis to keep connections stable
• Helps prevent board movement that can cause intermittent electrical issues or noise
• Restores proper mounting after service or component replacement

• Turn off and unplug the appliance before starting any repair
• Use appropriate screwdriver and avoid over-tightening to prevent board or thread damage
• Wear eye protection and keep small parts away from children and pets

This is the electronic control board that governs the appliance's main functions and user interface, replacing a failed board to restore normal control and cycle operation. It fits the OEM form and connects to factory wiring. What it does:

• Manages timed cycles, user inputs, and electronic commands for the appliance
• Controls display and indicator responses so settings register correctly
• Helps resolve symptoms like unresponsive controls, incorrect cycle behavior, or blank/error displays
• Interfaces with sensors and relays to coordinate heating, motor, and valve operation

• Disconnect power to the appliance before attempting service to avoid shock
• Handle the board by its edges and avoid static discharge; use an anti-static strap if available

This is a replacement mounting screw used to secure the dual safety valve assembly on compatible gas ranges and ovens. It restores proper fastening so the valve stays firmly in place during operation. What it does

• Secures the safety/dual gas valve to the appliance chassis or manifold
• Prevents valve movement that can interfere with burner operation or alignment
• Commonly replaced when original screw is missing, stripped, or damaged
• Matches OEM thread size and length for correct fit and retention

• One (1) screw, size 10-16 x 0.486

• Disconnect power and shut off gas supply before starting work; follow all safety procedures
• Thread carefully to avoid cross-threading; do not overtighten — snug to OEM torque specification
• Inspect surrounding mounting holes and hardware; replace any stripped or damaged parts for a secure fit

The Screw is an OEM part for Frigidaire ranges and ovens. This part is designed to securely fasten various parts of the appliance, ensuring stability and durability. 

Over time, screws can become loose due to the expansion and contraction of materials with temperature changes. Regular use and the occasional necessary removal for repairs or cleaning can also wear down the threads, making them less effective.  

Symptoms of a bad Screw (Chrome) include:

• Loose or wobbly components that should be securely fastened.
• Difficulty in securing parts due to stripped or damaged screw threads.
• Visible corrosion or deterioration of the screw.

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

Size: 8-18 x 0.5 inch. Color: Chrome.