Parts for Frigidaire GCRG3060ADE: Backguard Parts

This door hinge cover shields and protects the refrigerator hinge area from dirt and damage while giving the hinge a finished appearance. Replaces a worn, cracked, or missing cover to restore proper fit and appearance. What it does

• Covers and protects the door hinge assembly from debris and accidental contact
• Helps maintain a finished look by hiding hinge hardware and mounting fasteners
• Prevents sharp edges from being exposed, reducing snag and scratch risk
• Commonly replaced when cracked, broken, or missing after impact or wear

• One door hinge shield

• Remove power and open the door before servicing to prevent injury
• Typically installs with a few screws or clips—retain original fasteners unless replacement specified
• Handle part carefully to avoid scratching painted surfaces; align shield before tightening

This small protective cap covers and protects exposed appliance hardware, keeping dirt and moisture out while preventing accidental contact. It's a simple replacement that restores a finished appearance and helps maintain part integrity. What it does:

• Covers and protects an exposed shaft, tab, or fastener from debris and wear
• Helps prevent accidental contact with sharp or moving parts
• Restores the finished look of the appliance where the original cap was lost or damaged
• Simple, passive part—no electrical or mechanical function to reconfigure

• One replacement protective cap

• Always unplug the appliance or disconnect power before servicing
• Remove the damaged cap by hand or with a gentle pry tool; press the replacement into place until fully seated
• Small part—keep away from children and pets; loss is common during disassembly

This backguard panel replaces the vertical trim behind the range controls to restore appearance and protect internal components from spills and heat. It gives a finished look to the rear of the cooktop while covering wiring and control openings. What it does:

• Covers and protects the rear control area and internal components from splashes, grease, and heat
• Restores the range's original appearance when the backguard is scratched, dented, or warped
• Provides the mounting surface for control hardware and trim pieces
• Helps maintain a sealed area behind controls to limit debris buildup

• One backguard panel (black stainless) as pictured

• Disconnect power to the appliance before any service to avoid electrical shock
• Removal typically requires lifting or removing the cooktop and/or control console; keep screws and small parts organized
• Use caution handling sheet metal edges to avoid cuts; wear gloves

The Control Board is an OEM component specifically designed for Frigidaire electric ranges. As the processing center, it regulates oven temperatures, timers, surface heating elements, and diagnostic functions. 

Symptoms of a faulty control board include:

• Inability to turn stove top burners or oven on
• Temperature controls not accurately sense or setting heat 
• Codes appearing for malfunctions in logic circuits

Causes of a bad control board can include general wear from repeated thermal cycling. Potential spills on cooktops pose threats to sensitive semiconductor chips.

This OEM Frigidaire part is also compatible with Electrolux, Crosley, and some Kenmore models. Replacing restores reliable operation of all temperature calibration and safety protections as intended by the manufacturer. Maintaining control boards prevents disruptive breakdowns.
 

The Relay Board is an OEM part for Frigidaire ranges. It is an electronic component that controls the operation of various range functions and components by directing electrical currents through a network of relays.

Causes of a bad relay board include failure of electronic components over time due to continuous use, component fatigue, water damage, or surges/spikes in electrical current.

Symptoms of a bad range relay board include:

• Inoperable or unreliable oven/range functions such as bake, broil, warm, etc.
• Issues with cooktop burner ignition or flame level control
• Inconsistent or inaccurate temperature readings
• Error codes or diagnostic trouble codes appearing

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This is a replacement mounting screw used to secure the dual safety valve assembly on compatible gas ranges and ovens. It restores proper fastening so the valve stays firmly in place during operation. What it does

• Secures the safety/dual gas valve to the appliance chassis or manifold
• Prevents valve movement that can interfere with burner operation or alignment
• Commonly replaced when original screw is missing, stripped, or damaged
• Matches OEM thread size and length for correct fit and retention

• One (1) screw, size 10-16 x 0.486

• Disconnect power and shut off gas supply before starting work; follow all safety procedures
• Thread carefully to avoid cross-threading; do not overtighten — snug to OEM torque specification
• Inspect surrounding mounting holes and hardware; replace any stripped or damaged parts for a secure fit

The Screw is an OEM part for Frigidaire ranges and ovens. This part is designed to securely fasten various parts of the appliance, ensuring stability and durability. 

Over time, screws can become loose due to the expansion and contraction of materials with temperature changes. Regular use and the occasional necessary removal for repairs or cleaning can also wear down the threads, making them less effective.  

Symptoms of a bad Screw (Chrome) include:

• Loose or wobbly components that should be securely fastened.
• Difficulty in securing parts due to stripped or damaged screw threads.
• Visible corrosion or deterioration of the screw.

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

Size: 8-18 x 0.5 inch. Color: Chrome.