Parts for Frigidaire LGGF3046TDA: Backguard Parts

This door hinge cover shields and protects the refrigerator hinge area from dirt and damage while giving the hinge a finished appearance. Replaces a worn, cracked, or missing cover to restore proper fit and appearance. What it does

• Covers and protects the door hinge assembly from debris and accidental contact
• Helps maintain a finished look by hiding hinge hardware and mounting fasteners
• Prevents sharp edges from being exposed, reducing snag and scratch risk
• Commonly replaced when cracked, broken, or missing after impact or wear

• One door hinge shield

• Remove power and open the door before servicing to prevent injury
• Typically installs with a few screws or clips—retain original fasteners unless replacement specified
• Handle part carefully to avoid scratching painted surfaces; align shield before tightening

This small protective cap covers and protects exposed appliance hardware, keeping dirt and moisture out while preventing accidental contact. It's a simple replacement that restores a finished appearance and helps maintain part integrity. What it does:

• Covers and protects an exposed shaft, tab, or fastener from debris and wear
• Helps prevent accidental contact with sharp or moving parts
• Restores the finished look of the appliance where the original cap was lost or damaged
• Simple, passive part—no electrical or mechanical function to reconfigure

• One replacement protective cap

• Always unplug the appliance or disconnect power before servicing
• Remove the damaged cap by hand or with a gentle pry tool; press the replacement into place until fully seated
• Small part—keep away from children and pets; loss is common during disassembly

This backguard panel replaces the vertical trim behind the range controls to restore appearance and protect internal components from spills and heat. It gives a finished look to the rear of the cooktop while covering wiring and control openings. What it does:

• Covers and protects the rear control area and internal components from splashes, grease, and heat
• Restores the range's original appearance when the backguard is scratched, dented, or warped
• Provides the mounting surface for control hardware and trim pieces
• Helps maintain a sealed area behind controls to limit debris buildup

• One backguard panel (black stainless) as pictured

• Disconnect power to the appliance before any service to avoid electrical shock
• Removal typically requires lifting or removing the cooktop and/or control console; keep screws and small parts organized
• Use caution handling sheet metal edges to avoid cuts; wear gloves

This oven control board is responsible for the main functions of the range and oven area. If the oven's control board has begun to malfunction, there will be noticeable changes. The timing mechanisms for cooking and broiling are normally the first functions to quit working properly. Certain burners may work intermittently without warning. If the oven is in continued use while these malfunctions are taking place, be mindful of the cook timer not powering the oven off after the desired baking time. Remember to unplug the oven from its main power source before starting any repairs. Slide the oven from the wall, so the back of the appliance is exposed. Remove the small screws around the main console that anchor it in place. Use a flathead screwdriver to pry off the cap. After removing the cap, lift it up on the main console, and it should pop right out. Find the control board and unplug it from its wire harness, and remove the screws from the assembly it's housed in. Take the old control board out of the assembly and prepare to install the new part. Repeat these steps in reverse for installation of the replacement.This Frigidaire range oven control board is a genuine OEM part sourced directly from Frigidaire and is sold individually. This part is compatible with Frigidaire, JennAir, and Electrolux appliances.

The Overlay is an OEM part for Frigidaire ranges and ovens. This part serves as the protective and decorative cover for the control panel. It features the control labels and markings that guide users in operating the appliance, making it an essential element for both functionality and aesthetics.  

Symptoms of a bad Overlay include:

• Peeling or fading labels, making it difficult to read settings or operate the appliance correctly.
• Cracks or damage to the overlay, which can lead to moisture infiltration and potential damage to the underlying electronic components.
• Adhesive failure, causing the overlay to detach from the control panel, which can interfere with the operation and overall appearance of the appliance.

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

This is a replacement mounting screw used to secure the dual safety valve assembly on compatible gas ranges and ovens. It restores proper fastening so the valve stays firmly in place during operation. What it does

• Secures the safety/dual gas valve to the appliance chassis or manifold
• Prevents valve movement that can interfere with burner operation or alignment
• Commonly replaced when original screw is missing, stripped, or damaged
• Matches OEM thread size and length for correct fit and retention

• One (1) screw, size 10-16 x 0.486

• Disconnect power and shut off gas supply before starting work; follow all safety procedures
• Thread carefully to avoid cross-threading; do not overtighten — snug to OEM torque specification
• Inspect surrounding mounting holes and hardware; replace any stripped or damaged parts for a secure fit

The Screw is an OEM part for Frigidaire ranges and ovens. This part is designed to securely fasten various parts of the appliance, ensuring stability and durability. 

Over time, screws can become loose due to the expansion and contraction of materials with temperature changes. Regular use and the occasional necessary removal for repairs or cleaning can also wear down the threads, making them less effective.  

Symptoms of a bad Screw (Chrome) include:

• Loose or wobbly components that should be securely fastened.
• Difficulty in securing parts due to stripped or damaged screw threads.
• Visible corrosion or deterioration of the screw.

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

Size: 8-18 x 0.5 inch. Color: Chrome.

The Screw is an OEM part for Frigidaire ranges and ovens. This part is designed to securely fasten various parts of the appliance, ensuring stability and durability. 

Over time, screws can become loose due to the expansion and contraction of materials with temperature changes. Regular use and the occasional necessary removal for repairs or cleaning can also wear down the threads, making them less effective.  

Symptoms of a bad Screw (Chrome) include:

• Loose or wobbly components that should be securely fastened.
• Difficulty in securing parts due to stripped or damaged screw threads.
• Visible corrosion or deterioration of the screw.

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

Size: 8-18 x 0.5 inch. Color: Chrome.