Parts for Frigidaire PGLEF388CS4: 03 - Backguard Parts

This support is a direct-fit replacement mounting bracket that secures and stabilizes interior components so drawers, shelves and panels stay aligned and operate smoothly. Restores proper support and reduces binding or sagging. What it does:

• Provides a stable mounting point to hold a drawer, shelf or panel in place
• Prevents sagging or misalignment that can cause binding or uneven operation
• Helps maintain proper clearance for smooth opening and closing
• Reduces noise caused by loose or unsupported components

• Disconnect power before servicing the appliance to avoid shock
• Use basic hand tools; keep fasteners and clips for reinstallation if present
• Handle molded plastic parts gently to avoid cracking during removal/installation
• If alignment issues persist after replacement, inspect adjacent slides, rails or clips

This part has been discontinued by the manufacturer and is no longer available.

This is the LED display lens that covers and protects the appliance console, keeping the display visible and shielding the underlying LEDs from dirt and damage. It restores a clean, readable control panel appearance. What it does

• Protects the LED display and control indicators from dust, spills, and physical damage
• Diffuses and directs LED light for consistent display visibility
• Helps restore a clean, readable control panel when the original lens is scratched, cracked, or discolored
• Prevents debris from reaching the electronic display components

• One LED display lens

• Disconnect power to the appliance before starting any repair
• Typically installs from the console/front panel; may require removing trim or the control console
• Handle carefully to avoid scratching or cracking the lens during installation

This surface element control replaces the damaged or worn control that regulates heat to an electric cooktop burner. Restores reliable power and heat adjustment for a single surface element on compatible ranges. What it does

• Acts as the infinite switch that controls the burner's heat level based on the knob setting.
• Replaces a control that causes a burner to stay off, fail to heat, or not respond to knob changes.
• Helps eliminate intermittent heating, erratic temperature changes, or a burner that won't cycle properly.
• Works with the corresponding burner element and knob to provide stepped heat control.

• Disconnect power to the range at the breaker before starting any repairs.
• Basic hand tools required; remove the cooktop or rear console per your model's service instructions.
• Handle terminals and wiring carefully; match wire locations exactly during reassembly.

This dual infinite switch controls the inner and outer portions of a dual surface element on your range, providing smooth, adjustable heat levels. Replacing a failed switch restores reliable heating and proper temperature regulation for both ring sizes.

• Regulates power to both the small and large sections of a dual burner
• Typical failure symptoms: only one ring heats, no heat, won't switch between sizes, or heat stuck on high/erratic
• Mounts behind the surface knob and governs burner temperature settings
• Restores consistent simmer-to-boil control across all settings

• Disconnect power at the breaker and allow the cooktop to cool completely
• Access the control panel, then photograph or label all wire positions before removal
• Move wires to the new switch one at a time, matching terminal markings
• Reuse the existing knob; reassemble and test both inner and outer element settings

This truss-head machine screw secures a switch to its mounting bracket or panel. Replacing a worn or missing screw restores a solid, aligned switch fit for reliable operation.

• Fastens the switch body to a bracket or chassis panel
• Helps keep the switch aligned for consistent actuation
• Replaces stripped, corroded, or missing mounting hardware
• Common symptoms: loose or wobbly switch, misalignment, rattling or vibration around the switch area

• Disconnect power to the appliance before servicing
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Verify thread size and length match the original hardware
• If multiple screws secure the switch, replace them in a consistent pattern to maintain alignment

This is an oval-head square-drive screw used to secure interior and exterior appliance components. It provides a low-profile finish and corrosion-resistant black finish for a neat, durable hold. What it does:

• Fastens panels, brackets, trim pieces, and other sheet-metal or plastic parts
• Oval head gives a slightly countersunk, finished appearance when installed
• Square (Robertson) drive resists cam-out for easier tightening
• Common replacement when original screws are stripped, missing, or corroded

• Use the correct square-drive (Robertson) bit to avoid stripping the screw head
• Hand-start the screw to ensure proper alignment before using power tools
• Do not overtighten; stop once the part is snug to avoid thread or panel damage
• Disconnect power and follow appliance safety precautions before servicing

This is a #8 screw, 0.500 inch long, used to secure panels and components in appliances. It provides a correct-fit fastener for repairs where the original #8 x 1/2" screw was required, restoring proper assembly and stability. What it does:

• Fastens trim, panels, brackets and small components where a #8 x 1/2" screw is specified
• Holds parts securely to prevent rattling, gaps or loose panels
• Replaces worn, stripped or missing screws to restore proper fit
• Appropriate for common interior and exterior appliance mounting points

• Use the correct screwdriver (typically Phillips) and avoid over-tightening to prevent strip or damage
• Disconnect power and follow appliance manufacturer safety instructions when accessing internal parts

This control mounting lock secures the washer control or door latch area so the machine runs safely and reliably. It replaces a worn or broken mounting lock to restore proper control-panel or latch stability during cycles. What it does:

• Holds the washer control or latch assembly firmly in place to prevent movement and intermittent connections
• Helps maintain reliable electronic or mechanical engagement during start and spin cycles
• Common symptom: control panel or door area feels loose, intermittently unseated, or causes error codes related to a loose latch/control
• Prevents excess vibration or shifting of the control/latch that can lead to premature wear

• One control mounting lock

• Disconnect power and water before servicing to avoid shock or injury
• Access may require removing the cabinet or control panel; follow for safe disassembly
• Inspect surrounding clips and connectors; replace any damaged fasteners for a secure fit

Replacement machine screw used to secure appliance panels and internal components, restoring a stable fit and reducing rattling. Matches a 10-32 thread with a 17/32-inch length for original fastener locations. What it does:

• Fastens panels, trim pieces, and internal brackets; a missing or damaged screw can cause loose panels or rattling noises.
• Secures knobs, control housings and small assemblies to prevent wobble or misalignment.
• Restores proper fit for components so doors and access panels sit evenly and function reliably.

• Disconnect power (unplug or shut off circuit) before accessing components.
• Use the correct driver and tighten by hand; avoid overtightening to prevent stripped threads or cracked plastic.
• Keep any original washers or clips and reinstall them with the screw.

This control mounting hex nut secures the burner or oven control to the control panel, keeping the shaft stable so the knob turns smoothly and the switch stays properly aligned.

• Threads onto the control/infinite switch or thermostat bushing to fasten it to the panel
• Prevents the control from rotating or shifting when the knob is turned
• Replace if the original nut is missing, stripped, rounded, or corroded
• Common signs: loose or wobbly knob, switch spins in the panel, or misaligned knob indexing

• Disconnect power; for gas appliances, also shut off gas before servicing
• Pull off the knob and any trim; support the control body from behind the panel while removing/installing the nut
• Start the new nut by hand to avoid cross-threading; tighten snugly with the correct-size wrench—do not overtighten
• The control sits square in the panel and the knob operates smoothly before restoring power