Parts for Kenmore 790.74459810 (79074459810, 790 74459810): Backguard Parts

This door hinge cover shields and protects the refrigerator hinge area from dirt and damage while giving the hinge a finished appearance. Replaces a worn, cracked, or missing cover to restore proper fit and appearance. What it does

• Covers and protects the door hinge assembly from debris and accidental contact
• Helps maintain a finished look by hiding hinge hardware and mounting fasteners
• Prevents sharp edges from being exposed, reducing snag and scratch risk
• Commonly replaced when cracked, broken, or missing after impact or wear

• One door hinge shield

• Remove power and open the door before servicing to prevent injury
• Typically installs with a few screws or clips—retain original fasteners unless replacement specified
• Handle part carefully to avoid scratching painted surfaces; align shield before tightening

This end cap is a fitted trim piece that replaces a worn or broken edge cover to restore the appliance's finished appearance and protect internal components from dust and contact. It's a simple cosmetic and protective repair. What it does:

• Covers and protects an exposed end or edge, preventing debris and accidental contact
• Secures adjacent trim or panels and helps keep them aligned
• Restores the appliance's original finished look where caps are cracked or missing
• Reduces the chance of snagging fabric or skin on a damaged edge

• Disconnect power to the appliance before starting any repair to avoid shock or injury
• Usually installs by aligning tabs and snapping into place; some applications may use one or two small screws
• Inspect surrounding trim for damage and replace any broken fasteners for a secure fit

This end cap is a small replacement trim piece that covers and protects the exposed edge of a cabinet, rail or appliance trim for a finished look and to prevent snags. It restores the original fit and appearance where the previous cap is cracked, broken or missing. What it does

• Covers an exposed end of a trim, rail or slide to prevent clothing or hands from catching
• Holds the trim edge in place and keeps debris out of the end opening
• Restores proper appearance when the original end cap is cracked, broken or lost
• Works as a direct-fit replacement when the OEM part number matches

• One end cap as shown

• Typically installs by snapping into place; no special tools required for most applications
• Verify orientation (left/right or top/bottom) before installing
• If the cap is part of a powered assembly, disconnect power before service
• Inspect mating trim for damage and clean the mounting area before fitting the new cap

This end cap is a small replacement trim piece that restores a finished edge and helps secure a refrigerator shelf or rail. It prevents catches and improves fit for worn or damaged trim pieces. What it does

• Covers and protects the exposed end of a shelf rail or trim piece to prevent snagging.
• Helps hold shelf or rail components in place for a flush, secure fit.
• Restores cosmetic appearance where the original end cap is cracked, missing, or worn.
• Simple, durable plastic construction suited for normal refrigerator use.

• One end cap as pictured and specified by the part number.

• Disconnect power to the appliance before servicing to avoid injury.
• Access may require removing the shelf, bin, or rail; keep track of any screws or clips.
• End caps generally press into place or secure with a small screw or clip—do not force; align then snap or fasten per the original mounting.

This control panel overlay replaces a worn or damaged console face to restore the printed labels and appearance of your appliance's control area. It provides a clean, readable surface for the buttons and display. What it does:

• Replaces faded, cracked, or peeling panel graphics so controls are easy to read
• Protects the underlying control board and button openings from dirt and spills
• Restores the appliance's finished appearance around the control area
• Helps maintain correct button/label alignment for user input

• Disconnect power to the appliance before any service.
• Remove the control console per the service manual to access and replace the overlay; avoid forcing plastic tabs.
• Handle carefully to prevent scratching the printed surface; clean mounting surface before installing.

This replacement control knob restores tactile control for a range/oven/stove panel, letting you select heat or function settings easily. It replaces a cracked, worn, missing, or hard-to-turn knob so controls operate smoothly. What it does

• Fits onto the control shaft and provides a user grip for selecting settings.
• Replaces knobs that are cracked, stripped, loose, or have a missing indicator.
• Restores clear tactile feedback and indexed detents for accurate setting selection.
• Helps prevent accidental slips when adjusting temperature or function.

• One control knob.

• Disconnect power (and gas if applicable) before servicing the appliance.
• Pull the old knob straight off the control shaft; align the replacement splines and push the new knob fully onto the shaft.
• Verify the knob indexes correctly to the control markings and operates smoothly through all positions.
• If the knob does not seat or turns freely on the shaft, inspect the shaft for damage and replace the underlying control if needed.

This control knob replaces a worn, cracked or missing appliance control knob to restore a secure grip and easy setting of heat or function. It helps make selecting oven or cooktop settings smooth and predictable. What it does:

• Replaces a damaged or missing control knob so you can change settings without slipping or difficulty.
• Provides a secure fit on the control shaft for accurate selection of temperature or element levels.
• Common symptom fixes: knob is cracked, loose, stuck, or won't stay on the shaft.
• Simple mechanical part — no electrical components.

• Disconnect power to the appliance (unplug or shut off circuit breaker) before servicing.
• Remove the old knob by pulling straight off the control shaft; align the splines and push the new knob on until fully seated.
• Do not force the knob; if it does not seat easily, check alignment or inspect the control shaft for damage.

This trim is a decorative finish piece for select ranges and wall ovens. It covers gaps and raw edges for a clean look and helps keep adjacent panels properly seated when the original becomes cracked, bent, or missing.

• Provides a finished appearance by covering exposed edges or gaps
• Helps maintain alignment of nearby panels or glass
• Replace if cracked, warped, missing, or no longer seats securely
• Common symptoms include loose/rattling panels and exposed or sharp edges

• Disconnect power; for gas models, also shut off the gas supply
• Wear gloves—edges can be sharp
• Remove old trim and transfer/reuse original screws or clips
• Align the new trim and secure with existing fasteners; confirm proper fit before reassembly

This is a replacement mounting screw used to secure the dual safety valve assembly on compatible gas ranges and ovens. It restores proper fastening so the valve stays firmly in place during operation. What it does

• Secures the safety/dual gas valve to the appliance chassis or manifold
• Prevents valve movement that can interfere with burner operation or alignment
• Commonly replaced when original screw is missing, stripped, or damaged
• Matches OEM thread size and length for correct fit and retention

• One (1) screw, size 10-16 x 0.486

• Disconnect power and shut off gas supply before starting work; follow all safety procedures
• Thread carefully to avoid cross-threading; do not overtighten — snug to OEM torque specification
• Inspect surrounding mounting holes and hardware; replace any stripped or damaged parts for a secure fit

The Screw is an OEM part for Frigidaire ranges and ovens. This part is designed to securely fasten various parts of the appliance, ensuring stability and durability. 

Over time, screws can become loose due to the expansion and contraction of materials with temperature changes. Regular use and the occasional necessary removal for repairs or cleaning can also wear down the threads, making them less effective.  

Symptoms of a bad Screw (Chrome) include:

• Loose or wobbly components that should be securely fastened.
• Difficulty in securing parts due to stripped or damaged screw threads.
• Visible corrosion or deterioration of the screw.

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

Size: 8-18 x 0.5 inch. Color: Chrome.