Parts for Maytag AGR5330BAS0: 03 - Backguard Parts

Color: White

Right Hand Endcap

Color: White

Left Hand Endcap

Color: Black

Right Hand Endcap

Color: Black

Left Hand Endcap

Factory replacement screw that secures appliance components and hardware. Use it to replace a missing, stripped, or corroded fastener to restore a tight, rattle-free fit and help prevent loosening or damage from vibration.

• Fastens brackets, panels, or internal parts at the original mounting points
• Replaces worn or missing hardware to correct loose or misaligned components
• Helps reduce vibration-related noise and movement
• Matches the original thread and length specified for the application

• Disconnect power; shut off water or gas if applicable before servicing
• Compare to the original for thread and length match before installation
• Start threads by hand to avoid cross-threading; tighten snugly—do not overtighten
• Reuse any original spacers/washers if present; replace if damaged

This electronic control board is the dishwasher's central controller. It manages cycle timing and powers key loads so the machine fills, washes, drains, and dries correctly, restoring reliable operation when the original board fails.

• Coordinates water fill, wash circulation, drain, and heating functions according to the selected cycle
• Monitors door switch, sensors, and keypad inputs to advance through cycles
• Sends power/control signals to pumps, valve, and heater
• Common failure symptoms: won't start, unresponsive controls, stops mid-cycle, won't advance, blinking lights/error codes

• Disconnect power before service; use ESD protection when handling the board
• Document wire locations; move connectors one at a time and ensure locking tabs are fully seated
• Transfer any model-specific jumpers or mounting hardware from the original board if applicable
• After installation, restore power and run the unit's diagnostic/reset procedure per the service manual if needed

This electronic control board is the dishwasher's central controller. It manages cycle timing and powers key loads so the machine fills, washes, drains, and dries correctly, restoring reliable operation when the original board fails.

• Coordinates water fill, wash circulation, drain, and heating functions according to the selected cycle
• Monitors door switch, sensors, and keypad inputs to advance through cycles
• Sends power/control signals to pumps, valve, and heater
• Common failure symptoms: won't start, unresponsive controls, stops mid-cycle, won't advance, blinking lights/error codes

• Disconnect power before service; use ESD protection when handling the board
• Document wire locations; move connectors one at a time and ensure locking tabs are fully seated
• Transfer any model-specific jumpers or mounting hardware from the original board if applicable
• After installation, restore power and run the unit's diagnostic/reset procedure per the service manual if needed

This factory screw secures appliance components to their mounting points. Replace missing, worn, or stripped hardware to restore a tight fit, proper alignment, and quieter operation across the affected assembly.

• Fastens panels, brackets, covers, or internal parts to the chassis or frame
• Helps maintain alignment and support, reducing rattle, vibration, or looseness
• Replaces missing or damaged screws that have backed out, broken, or stripped
• Restores secure mounting after service when original hardware is lost

• Disconnect power; shut off water or gas supplies before servicing
• Use the correct driver; start threads by hand to avoid cross-threading
• Match length and thread to the original location; do not substitute with longer hardware
• Tighten snugly; do not overtighten into plastic or thin metal

This mounting bracket secures appliance components and panels to keep assemblies aligned and stable, helping prevent rattles and loose parts. It's a simple replacement that restores proper fit and support where the original bracket has failed. What it does:

• Provides rigid support for internal components or exterior panels to maintain alignment
• Stops vibration and rattling caused by a broken or bent bracket
• Restores secure attachment points for screws and fasteners
• Helps prevent additional wear from loose parts moving during operation

• Always unplug the appliance or disconnect power before starting any repair
• Remove necessary access panels to reach the damaged bracket; keep track of fasteners
• Reuse original screws if undamaged; replace stripped or corroded fasteners
• If alignment issues persist after installation, recheck fit and mounting points for damage