Parts for Bosch WTA3510UC/13: Base Assy Parts

A sealing kit designed to replace worn seals in the dishwasher pump area to stop leaks and restore a watertight pump assembly. Ideal when seals fail and allow water to escape around the pump. What it does:

• Replaces worn or damaged pump seals to help stop leaks beneath the machine
• Restores the pump assembly's watertight seal for proper water circulation and drainage
• Helps prevent water damage to the cabinet and flooring caused by seal failure
• Commonly used when you find water under the dishwasher, visible leaks near the pump, or damp cabinet flooring

• One sealing kit

• Disconnect power and shut off the water supply before starting any repair
• Access usually requires removing the lower access panel and may require partial pump disassembly
• Keep track of small seals and O-rings during removal; inspect related parts for wear

This Vent Adapter is an OEM part for Bosch Dryers. It plays a role in connecting the dryer exhaust to the vent hose, ensuring efficient airflow and proper ventilation. Over time, wear and tear or improper installation can lead to issues with this component.

What Causes a Bad Vent Adapter: 
Continuous use or improper fitting can cause the vent adapter to degrade or become loose. Exposure to heat and moisture from the dryer can also contribute to its deterioration.

Symptoms of a Bad Vent Adapter:

• Poor dryer performance
• Difficulty in connecting the vent hose
• Air leaks around the vent connection

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

This genuine OEM replacement part is a pulley assembly for dryers. Sometimes called an idler arm, the pulley assembly keeps the dryer drive belt under tension as the belt wraps around the dryer drum. If the dryer is no longer spinning properly and is making a lot of noise, the pulley assembly may need to be replaced. Luckily this repair is a relatively simple process.To remove the old dryer pulley assembly, start by making sure the dryer is unplugged. Remove the lint screen from the top of the dryer. Remove the two Phillips screws by the lint screen opening. Depress the clips that hold the top cover down. Lift the top cover and keep it in an upright position. Disconnect the wire harness to the switch that separates the connector. Remove the screws on the front panel. Lift the panel forward and set it to the side. Next, lift the drum and locate the pulley assembly under the drum. Lift the belt off the motor pulley to remove the assembly. Set the new pulley assembly in the same position as the old one and make sure everything is aligned. Rotate the drum to make sure it rotates smoothly. reinstall the panels.This replacement part is sold individually and is compatible with Bosch, Gaggenau, and Thermador dryers.

This part is a drive pulley with bearings, also known as a dryer roller. The purpose of this component is to allow the dryer to tumble properly by providing support to the drum cylinder. The drive pulley provides the tension needed.When the drive pulley begins to go bad, the unit may begin making loud noises while running. This could include squeaking, thumping, or squealing noises. Be sure to unplug the dryer before attempting to work on this part.This part is sold individually and comes straight from the manufacturer. This particular drive pulley with bearings is compatible with dryer units that are manufactured by Bosch. This could include brands such as Thermador and Gaggenau in addition to Bosch.

This end cap for a pulley assembly secures and supports the appliance drive pulley so the belt and drum run smoothly. Replacing a worn end cap restores proper pulley alignment and reduces noise from the drive area. What it does

• Holds the pulley in proper position on the shaft to maintain belt alignment
• Helps prevent excess pulley wobble that can cause noise or rubbing
• Supports smooth rotation of the pulley to reduce belt wear and slipping
• Addresses symptoms such as squealing, grinding, or loose-feeling drive components

• Disconnect power (and gas if applicable) before starting any repair
• Inspect surrounding pulley, bearings, and belt for wear and replace if needed
• Use correct tools and follow OEM service instructions for safe removal and installation

The Blower Belt is an OEM part for Bosch dryers. This belt efficiently transmits rotation from the motor to the blower fan, circulating heated air through the dryer drum.

Causes of a bad blower belt can include drying and cracking from heat exposure over many cycles.

Symptoms of a bad blower belt include:

• The blower fan not spinning or rotating slower than usual
• Longer dry times or an inability to fully dry clothes
• An intermittent squealing or squeaking noise from the belt

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

A small metal clip that secures the dryer to the top of the washer when stacking, keeping the pair stable during operation. Use this replacement clip if the original is bent, missing, or fails to hold the units together. What it does:

• Locks the dryer cabinet to the washer top to help prevent shifting or sliding during use
• Restores the mechanical fastening point used in factory stacking setups
• Common symptom: dryer feels loose or moves when the pair operate together
• Common symptom: visible bent, cracked, or missing clip at the stack connection

• Turn off and unplug both appliances before attempting installation
• Lift and support the dryer securely during alignment; use a second person or proper lifting equipment
• Slide or snap clip into the factory stacking locations per the appliance's service instructions