Parts for Bosch HMV5052U/01: Base Assembly Parts

Mounting screw for microwave installation and assembly. Replaces lost, stripped, or corroded screws used to secure panels, brackets, or hardware.

Replacement mounting screw for microwave panels and brackets. Secures components, eliminates rattling from loose panels, and restores proper fit.

A replacement circulation pump motor that restores water movement in the dishwasher's wash system for proper cleaning and rinsing. Installs in the pump assembly to replace a worn or failed motor and stop noisy or non-operating pumps. What it does:

• Drives the dishwasher's water circulation/pump assembly so wash arms receive proper water flow.
• Common symptom: little or no water spray during the wash cycle or poor cleaning performance.
• Common symptom: loud grinding, humming, or the pump not starting when the cycle runs.
• Works as the rotating motor portion of the pump; requires correct pump housing and seals for a leak-free installation.

• One motor

• Disconnect power and turn off water supply before beginning repair.
• Inspect pump housing, gaskets, and impeller during replacement; replace worn seals to prevent leaks.
• Handle the motor and electrical connections carefully; ensure connectors are fully seated and secured.
• After installation, restore power and run a short cycle to check for proper operation and leaks.

Replace your microwave's control panel if the surface is cracked, worn, or damaged. This panel mounts on the front and houses the button interface.

Holds the bulb and provides electrical connection for interior lighting. Replace if cracked, heat-damaged, or loose causing lights to fail. Confirm fit.

This replacement lamp restores proper lighting in your appliance, making it easier to see contents and monitor cycles. Install it when the original bulb burns out or flickers to bring clear, reliable illumination back.

• Provides illumination when the appliance's light circuit or door switch activates
• Common symptoms: no light, intermittent or flickering light, or a visibly failed bulb
• Heat, age, vibration, or moisture can cause the lamp to fail
• A new lamp typically resolves lighting issues if the socket and switch are sound

• Disconnect power at the breaker or unplug before servicing
• Allow the area to cool fully before opening the light cover
• Handle the glass with clean gloves or a cloth to avoid skin oils
• Install the exact replacement specified for your model; do not exceed the manufacturer's rating

Microwave not cooling or making loud noises? This fan motor circulates air to prevent overheating. Moderate DIY repair taking 30-45 minutes.

This replacement screw secures appliance panels and components at their mounting points. Swap in a new screw to restore a tight, rattle-free fit when the original fastener is missing, stripped, or corroded.

• Fastens the designated panel, bracket, or component in place
• Replaces a missing, stripped, or rusted screw
• Helps address loose panels, gaps, rattling, or misalignment at the mounting point
• Maintains proper assembly integrity after service or vibration

• Disconnect power; shut off water supply if working near plumbing
• Match to the removed fastener and replace one at a time to preserve alignment
• Start threads by hand to avoid cross-threading; use the correct driver bit
• Tighten snugly and avoid overtightening, especially into plastic or thin sheet metal

This grease filter traps airborne grease and cooking particles before they reach the ventilation blower and ductwork, helping maintain airflow and keep kitchen surfaces cleaner. Replace a saturated or damaged filter to restore effective venting.

• Captures grease and particulates from cooking vapors to protect the fan and internal components
• Helps maintain proper airflow and reduce lingering smoke or odors
• A clogged or damaged filter can cause weak venting, increased fan noise, visible grease buildup, or a filter-clean reminder to stay on
• Replace when mesh is torn, frame is bent, or the filter no longer stays secured

• Disconnect power to the ventilation unit before servicing
• Allow the hood to cool; support the filter while releasing the latch or tabs
• Note orientation; insert the new filter and latch securely
• Reset the filter reminder per the user manual after replacement

This replacement cover is a protective housing piece that shields internal components and helps keep the appliance operating safely and cleanly. It restores a finished appearance and prevents debris contact with parts. What it does:

• Protects internal components from dust, moisture, and physical contact
• Restores proper enclosure fit and appearance after cracks or missing pieces
• Helps reduce rattles or vibration caused by loose/missing covers
• Fits as the OEM replacement for the original cover

• Disconnect power (and water supply if applicable) before beginning any service
• Handle the cover gently to avoid cracking; use basic hand tools to remove/install clips or screws
• Align mounting tabs before snapping or fastening; do not force into position