Parts for Ge GFWS3705F0RR: Base Pan Parts

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.

The Damper Assembly is an OEM part for GE washing machines. It is designed to control the movement of the washer drum, providing stability and reducing vibrations during the spin cycle. It measures approximately 9 inches long and over 1 inch wide.

Causes of a bad damper assembly can include wear and tear from regular use, damage from unbalanced loads, or material fatigue.

Symptoms of a bad damper assembly include:

• Excessive shaking or vibrating during the wash cycle
• Loud banging noises during spinning
• The washer moving or shifting during operation
• Poor balance or wobbling of the drum

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Pin Damper is an OEM component specifically designed for GE washing machines. Located within the transmission housing, it provides a cushioning effect between the drive motor and gearing assemblies. 

Causes of a bad pin damper involve cracked rubber, sheared pins, or lack of lubrication from extended operational use over time.

Symptoms of a bad pin damper include:

• Grinding or vibration felt from transmission housing  
• Excessive noise emitted during gear-shifting changes
• Premature wear observed on drive shaft bushings/bearings

This OEM GE replacement pin damper helps reduce noise, protects components from impact shocks, and promotes smooth operation. Compatible with some Hotpoint, RCA, and Kenmore models as well, installation maintains optimized drivetrain performance. 

This 10-32 hex washer screw secures panels and components in appliances, providing a reliable fastener that helps keep parts aligned and vibration-free during operation. Designed for a snug fit in threaded appliance mounting holes. What it does:

• Fastens control panels, brackets, and assemblies to appliance frames
• Holds components tight to prevent rattling or movement during use
• Replaces stripped, missing, or corroded mounting screws
• Works where a 10-32 threaded connection and washer-style head are required

• One 10-32 hex washer screw

• Use the correctly sized 10-32 driver or nut driver to avoid stripping the head
• Do not overtighten; snug until secure to prevent thread damage
• Replace with the exact screw type to maintain proper fit and grounding where applicable
• Disconnect power to the appliance before removing panels or working near electrical components

This mount damper is the refrigerator air-damper support that helps direct and regulate cold air between compartments for more even temperatures. Fits replacement needs for dampers that are cracked, loose, or not seating correctly. What it does:

• Holds and supports the air damper assembly so the damper can open and close properly
• Guides cold air from the freezer into the fresh-food compartment to help maintain set temperatures
• Can cause uneven cooling, warm fresh-food section, or poor airflow when damaged or broken
• May reduce rattling or vibration if the original mount is worn or loose

• One mount damper (single replacement piece)

• Disconnect power to the appliance before beginning any repair
• Remove shelves, crispers, or trim panels as needed to access the damper area
• Handle plastic components carefully to avoid cracking during removal or install

This leveling leg assembly supports and stabilizes your washer by allowing you to adjust its height for a level installation. Keeping the appliance level helps reduce vibration, noise, and movement during operation.

• Adjusts the washer's stance to ensure it sits level on the floor
• Helps prevent excessive vibration, walking, and rattling noises
• Supports proper spin performance by improving machine stability
• Common fix when a foot is worn, damaged, or will not hold adjustment

• Unplug the washer and turn off water supply before servicing
• Tip the appliance carefully to access the leveling point
• Thread the new leg into the base and adjust until level; lock if applicable
• Verify all legs contact the floor firmly and recheck level after test run

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.