Parts for Ge GFWR4805F3RR: Base Pan & Riser Assembly Parts

The Affresh Washer Cleaner 3 Pack is an OEM cleaning accessory designed specifically for washing machines. This multipack contains 3 packets of a proven formula that helps eliminate odors from the washer tub, door, gasket, and drain areas. Regular cleaning is important to remove dirt, soap scum, mildew, and other residue that can build up over time and lead to odors. The Affresh tablets contain oxygen-powered enzymes and fresh scent boosters that are released during the cleaning cycle to safely and effectively eliminate musty smells.

This multipack of Green 4.2-ounce tablets ensures you have enough doses for consistent cleaning to keep your washer smelling fresh. As the #1 recommended washer cleaner brand, Affresh is also compatible for use in Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.

This riser side bracket assembly replaces a damaged or worn support bracket that holds the appliance riser/console in place. Restores proper alignment and stable support for the top/riser area to reduce wobble or gaps. What it does:

• Provides structural support for the riser/console and adjacent panels
• Helps keep the top panel and control console aligned and secure
• Can stop movement, rattling or misalignment caused by a broken bracket
• Matches OEM fit and mounting points for direct replacement

• Disconnect power to the appliance before starting any repair.
• Remove necessary panels or trim to access the riser bracket; keep track of fasteners.
• Align bracket to existing mounting points and secure with the original screws or clips unless replacement fasteners are provided.

This silicon controlled rectifier (SCR) switches and regulates power in compatible appliance control circuits, helping the unit deliver correct power to heating elements or motors. It's a direct replacement component when the original SCR fails. What it does

• Acts as a solid-state switch that controls current flow to heating elements, motors or other high-current circuits.
• Fails open or shorted when worn; common symptom is loss of heating, intermittent power to the controlled component, or no operation on affected circuits.
• Provides fast, repeatable switching compared with electromechanical relays.
• Designed for stud-mount installation with insulated/marked terminals for correct wiring.

• One silicon controlled rectifier (SCR) as listed.

• Disconnect all power before accessing or replacing the SCR to avoid shock or equipment damage.
• Note terminal orientation and wiring before removal; replace with the same terminal/stud configuration.
• Avoid electrostatic discharge to the replacement part; handle by the body and avoid touching terminals.

This hex washer head screw secures panels and internal components in your appliance. It replaces worn or missing hardware to keep assemblies tight and help reduce vibration-related looseness, noise, and misalignment. What it does:

• Fastens appliance panels, brackets, or trim with a hex washer head for a broad bearing surface
• Helps maintain proper alignment and a secure hold under vibration
• Replaces a damaged, stripped, or lost screw
• Symptoms include rattling panels, increased vibration/noise, or loose hardware

• 1 hex washer head screw

• Disconnect power; for washers, also turn off water supply before servicing
• Use the correct nut driver or socket; start threads by hand to avoid cross-threading
• Tighten snugly—do not overtighten, especially into plastic or thin sheet metal
• Replace hardware in sets when needed to maintain even clamping force

The Damper Assembly is an OEM part for GE washing machines. It is designed to control the movement of the washer drum, providing stability and reducing vibrations during the spin cycle. It measures approximately 9 inches long and over 1 inch wide.

Causes of a bad damper assembly can include wear and tear from regular use, damage from unbalanced loads, or material fatigue.

Symptoms of a bad damper assembly include:

• Excessive shaking or vibrating during the wash cycle
• Loud banging noises during spinning
• The washer moving or shifting during operation
• Poor balance or wobbling of the drum

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Affresh Washer Cleaner 3 Pack is an OEM cleaning accessory designed specifically for washing machines. This multipack contains 3 packets of a proven formula that helps eliminate odors from the washer tub, door, gasket, and drain areas. Regular cleaning is important to remove dirt, soap scum, mildew, and other residue that can build up over time and lead to odors. The Affresh tablets contain oxygen-powered enzymes and fresh scent boosters that are released during the cleaning cycle to safely and effectively eliminate musty smells.

This multipack of Green 4.2-ounce tablets ensures you have enough doses for consistent cleaning to keep your washer smelling fresh. As the #1 recommended washer cleaner brand, Affresh is also compatible for use in Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.

The Pin Damper is an OEM component specifically designed for GE washing machines. Located within the transmission housing, it provides a cushioning effect between the drive motor and gearing assemblies. 

Causes of a bad pin damper involve cracked rubber, sheared pins, or lack of lubrication from extended operational use over time.

Symptoms of a bad pin damper include:

• Grinding or vibration felt from transmission housing  
• Excessive noise emitted during gear-shifting changes
• Premature wear observed on drive shaft bushings/bearings

This OEM GE replacement pin damper helps reduce noise, protects components from impact shocks, and promotes smooth operation. Compatible with some Hotpoint, RCA, and Kenmore models as well, installation maintains optimized drivetrain performance. 

This mount damper is the refrigerator air-damper support that helps direct and regulate cold air between compartments for more even temperatures. Fits replacement needs for dampers that are cracked, loose, or not seating correctly. What it does:

• Holds and supports the air damper assembly so the damper can open and close properly
• Guides cold air from the freezer into the fresh-food compartment to help maintain set temperatures
• Can cause uneven cooling, warm fresh-food section, or poor airflow when damaged or broken
• May reduce rattling or vibration if the original mount is worn or loose

• One mount damper (single replacement piece)

• Disconnect power to the appliance before beginning any repair
• Remove shelves, crispers, or trim panels as needed to access the damper area
• Handle plastic components carefully to avoid cracking during removal or install

A replacement 10-16 shoulder screw (Type A) used to secure appliance components where a shoulder/clearance is required. Restores proper alignment and fastening for panels, brackets, or assemblies that use a shoulder-style fastener. What it does:

• Provides a fixed shoulder to control depth and spacing between parts
• Secures panels, brackets, or moving parts while allowing an exact clearance
• Helps prevent over-driving and protects mating parts from damage
• Commonly used where precise alignment or rotation clearance is needed

• Inspect the mating hole and threads for damage before installing
• Use the correct driver and torque—do not over-tighten to avoid stripping
• Replace with the same screw type and size to maintain proper fit and clearance
• Disconnect power and follow all safety precautions when accessing internal components

This leveling leg assembly supports and stabilizes your washer by allowing you to adjust its height for a level installation. Keeping the appliance level helps reduce vibration, noise, and movement during operation.

• Adjusts the washer's stance to ensure it sits level on the floor
• Helps prevent excessive vibration, walking, and rattling noises
• Supports proper spin performance by improving machine stability
• Common fix when a foot is worn, damaged, or will not hold adjustment

• Unplug the washer and turn off water supply before servicing
• Tip the appliance carefully to access the leveling point
• Thread the new leg into the base and adjust until level; lock if applicable
• Verify all legs contact the floor firmly and recheck level after test run

This guide pin bushing cushions and aligns a rotating guide pin, helping the appliance drum or assembly run smoothly and quietly. Replaces worn bushings to reduce noise and prevent pin-to-housing wear. What it does

• Provides a low-friction bearing surface for a guide pin or shaft.
• Keeps the pin centered to prevent wobble and misalignment during operation.
• Reduces noise and metal-on-metal wear caused by a worn or damaged bushing.
• Helps maintain proper movement of the drum/assembly for consistent performance.

• One guide pin bushing.

• Disconnect power before beginning any repair to avoid shock or injury.
• Access may require removing panels, the drum or related assemblies; follow service manual steps.
• Inspect surrounding parts (pin, housing, clips) and replace any damaged components.
• Use appropriate tools and avoid forcing the bushing into place; follow the OEM service instructions for torque/spec guidance.

The Affresh Washer Cleaner 3 Pack is an OEM cleaning accessory designed specifically for washing machines. This multipack contains 3 packets of a proven formula that helps eliminate odors from the washer tub, door, gasket, and drain areas. Regular cleaning is important to remove dirt, soap scum, mildew, and other residue that can build up over time and lead to odors. The Affresh tablets contain oxygen-powered enzymes and fresh scent boosters that are released during the cleaning cycle to safely and effectively eliminate musty smells.

This multipack of Green 4.2-ounce tablets ensures you have enough doses for consistent cleaning to keep your washer smelling fresh. As the #1 recommended washer cleaner brand, Affresh is also compatible for use in Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.