Parts for Kitchenaid KP2671: 03 - Base & Pedestal Unit, Literature Parts

Replacement rubber foot for stand mixers. Secures to the base to prevent movement and slipping during operation. Replace if cracked, worn, or missing.

Decorative panel for stand mixer in Imperial black finish. Replaces cracked, chipped, or discolored panels on the mixer housing exterior.

White decorative column cover for stand mixers. Replaces cracked, chipped, or discolored housing on the mixer body. Restores cosmetic appearance.

This door trim restores the appliance's exterior appearance by replacing a damaged or missing Caviar-finish trim piece. It returns a clean, finished look and helps cover fasteners and edges for a seamless door surface. What it does

• Replaces worn, scratched, or gouged trim to improve cosmetic appearance
• Covers mounting holes and seams for a finished look
• Helps maintain proper door alignment where trim interfaces with adjacent parts
• Common symptom: visible chips, scratches, or missing trim exposing fasteners

• One door trim piece in Caviar finish

• Disconnect power to the appliance before beginning service
• Use basic hand tools; remove surrounding trim or fasteners as required for access
• Handle carefully to avoid scratching the new finish during installation
• Follow model-specific instructions for correct alignment and fastening

A white replacement bowl support that centers and stabilizes the appliance bowl or glass tray to reduce wobble and noise, helping restore smooth rotation and reliable operation. What it does:

• Centers and supports the bowl or glass tray to prevent off-center rotation and rubbing.
• Keeps the tray steady to reduce vibration and noisy operation.
• Helps the tray rotate smoothly for even heating or proper function.
• Common symptoms it can address: wobbling or off-center bowl/tray, noisy rotation, scraping or unstable tray movement.

• Disconnect power to the appliance before starting any work.
• Remove the bowl or glass tray and lift out the old support; inspect the drive hub or shaft for damage.
• Align the support over the hub/shaft and press into place until fully seated; do not force broken or warped plastic.

If your mixer bowl won't stay in place or wobbles during mixing, this retainer clip secures it properly. Simple DIY fix takes just minutes to install.

Plastic lift arm that raises and lowers the mixing bowl on stand mixers. Replace if cracked, broken, or worn from frequent use and age.

Fixes misalignment and noisy operation caused by a cracked or worn support bowl. Restores proper centering of internal components. Direct replacement.

Small flat washer for KitchenAid stand mixers. Installs between mechanical components to ensure proper spacing. Replace if worn, cracked, or missing.

This replacement spring restores proper tension and return action within the original mechanism of your appliance. Replacing a fatigued or broken spring helps moving parts operate smoothly and return to position for consistent, reliable performance.

• Supplies controlled tension within the assembly
• Returns levers or linkages to their neutral position after use
• Helps maintain proper alignment and engagement of moving parts
• Common signs of failure: weak/loose feel, parts not returning, intermittent operation, rattling or squeaking

• Disconnect power before service; also shut off gas/water
• Note original routing and attachment points; take a reference photo before removal
• Use needle-nose pliers or a spring tool; avoid overstretching the new spring
• Verify smooth manual movement before reassembly and testing

If your stand mixer bowl lift won't stay up or slips out of position, this spring roll pin secures the lift arm linkage. Requires pin punch to install.

Need an extra mixing bowl for batch cooking or quick ingredient swaps? This stand mixer bowl locks securely in place. Easy 5-minute swap—no tools needed.

Upgrade or replace your mixer's paddle with this coated flat beater in Silent Silver. It restores smooth, even mixing performance for everyday recipes and is designed in the narrow profile specified for select stand mixers.

• Blends ingredients thoroughly for batters, doughs, and mashed mixtures
• Direct replacement for a beater that is bent, chipped, peeling, or missing
• Narrow profile mates correctly with the intended mixer hub style

• Unplug the mixer before attaching or removing the beater
• Tilt the head up or lower the bowl; align the beater slot with the shaft pin, push up, and twist to lock
• Clean and dry per the manufacturer's care instructions before first use

Restore proper kneading performance with this stand mixer dough hook. Replaces a worn or missing hook so your mixer can fold and stretch dough evenly for breads, pizza, and other yeast-based recipes. What it does:

• Attaches to the mixer's beater shaft to knead and mix yeast doughs
• Folds and stretches dough for even ingredient incorporation and structure development
• Helps prevent overmixing with the correct tool for heavy doughs
• Replace if the hook is bent, cracked, or no longer locks securely
• Common symptoms include uneven kneading, dough not coming together, or the attachment wobbling

• 1 dough hook

• Unplug the mixer before installing attachments
• Align the hook on the beater shaft; push up and twist to lock (typical on most models)
• Clean and care for the attachment according to your model's instructions

Replace your bent, worn, or broken wire whip attachment for KitchenAid stand mixers. Essential accessory for whipping cream and egg whites. 5-quart capacity.

Pouring shield attaches to 5-6 quart lift bowl stand mixer to prevent ingredients from flying out while mixing. Replace if lost or damaged. Verify fit.

Pouring shield attaches to 5-6 quart lift bowl stand mixer to prevent ingredients from flying out while mixing. Replace if lost or damaged. Verify fit.

Fix a mixer that won't engage or slips during operation. This cam restores proper mechanical linkage timing. Straightforward DIY replacement part.

Replacement mounting screw for stand mixer panels, brackets, and trim. Secures internal components to keep parts aligned. Replace if missing, stripped, or rusted.

Mounting screw secures internal brackets and panels in mixers. Replace if missing, stripped, or damaged to prevent loose components and rattling.

Fix mixer parts that shift or make noise with this retaining ring. Snaps into groove to secure components on shaft. Takes under 20 minutes to install.

If your mixer's bowl lift handle is cracked or missing, this rotating handle restores convenient bowl access. Simple installation—no tools needed.