Parts for Ge GVS04BDWFSS: Beverage Center Parts

This is the upper hinge assembly that attaches the top of the refrigerator door to the cabinet frame, allowing the door to pivot open and closed. It bears the weight of the door and keeps it properly aligned. Replace this hinge if the door is sagging, not closing properly, or if the hinge is visibly bent or corroded.

Replace the upper hinge cover on your wine or beverage cooler. This cosmetic trim piece conceals the top door hinge and may need replacement if cracked or missing.

This is a black rubber door gasket that seals the gap between the refrigerator door and the cabinet when the door is closed. It uses a magnetic strip to maintain a tight seal and keep cold air inside. Replace this gasket if you notice condensation forming around the door edges, the refrigerator is running constantly, or the seal is torn, cracked, or no longer holding the door shut.

Replace your refrigerator's damaged or broken door. This complete door assembly installs on the front of the unit. Needed when the original is cracked or worn.

Replace your refrigerator's cracked, broken, or worn door handle. This exterior handle mounts to the door for secure opening and closing access.

Replacement mounting screw for refrigerator interior components and panels. Needed when original hardware is stripped, lost, or damaged during repairs.

Wine cooler not cooling properly or displaying incorrect temperatures? This temperature probe wire monitors internal temps for accurate climate control.

This genuine replacement screw secures appliance panels and trim so parts stay aligned and rattle-free. It's a simple, low-cost fix that restores proper fit and prevents movement or vibration of covers and components. What it does:

• Fastens panels, trim, brackets, or components to maintain alignment and stability
• Stops rattling, vibration noise, and loose or sagging trims
• Helps ensure proper sealing and clearance where screws retain covers or housings
• Works wherever the OEM screw specification matches the original mounting point

• One replacement screw

• Use the matching screwdriver or bit to avoid stripping the head
• Turn slowly and stop when snug—do not overtighten to prevent thread or part damage
• Disconnect power or follow appliance-specific safety procedures before accessing internal parts
• Keep removed hardware organized so original placement can be restored

Fix your wine cooler that won't cool, has display issues, or temperature control problems. This control board manages all electronic functions. Moderate DIY.

This lamp socket connects the oven or appliance light bulb to the wiring harness so the interior light powers on safely and reliably. It replaces a cracked, loose, or burned socket to restore proper bulb contact and illumination. What it does:

• Holds the appliance light bulb and provides the electrical connection to power the lamp
• Restores steady bulb contact when the light flickers or works intermittently
• Replaces sockets that are cracked, melted, or have burned contacts
• Helps prevent arcing or poor connection that can cause bulb failure

• Disconnect power to the appliance before servicing to avoid shock
• Handle bulbs and glass components carefully; let recently used bulbs cool before removal
• Inspect wiring and connectors for damage; replace or repair wiring if needed
• Use appropriate replacement bulb type and wattage as specified by the appliance manufacturer

Replace your cracked or broken refrigerator glass shelf. Includes molded front stop to prevent items from sliding and contain spills. Direct-fit design.

Interior upper shelf for refrigerators. Organizes food and maximizes space. Replace if cracked, broken, or missing to keep contents level and accessible.

Replace your refrigerator's bottom door hinge if cracked, worn, or causing door misalignment. Mounts at the base of the door for secure closure.

A single replacement screw used to secure appliance panels, trim, or internal components. Restores proper fastening so doors, panels and mounts stay tight and aligned for safe, quiet operation. What it does

• Fastens trim, panels or brackets to the appliance chassis
• Replaces missing or stripped screws that cause loose parts or rattling
• Helps maintain proper alignment of doors and assemblies
• Prevents further wear or damage from unsecured components

• One screw

• Use the correct screwdriver to avoid stripping the head
• Do not overtighten; tighten until snug to avoid damaging threads or plastic
• Disconnect power or follow appliance safety procedures when working near electrical components

This PTC cover is the protective shroud that fits over a PTC thermistor/starting device to help keep the sensor assembly secure and shielded from debris and contact. It preserves reliable operation by protecting the component. What it does:

• Protects the PTC thermistor/assembly from physical damage and debris
• Helps retain proper sensor position and alignment for consistent operation
• Reduces risk of accidental contact with the thermistor or wiring
• Can prevent intermittent operation caused by a loose or damaged cover

• Disconnect power to the appliance before beginning any repair
• Access may require removing outer panels or an access cover; follow OEM service manual steps
• Handle the PTC thermistor and wiring carefully to avoid damage
• If mounting hardware is damaged or missing, replace with OEM-specified fasteners

Fix a compact refrigerator that won't cool or makes clicking sounds with this PTC relay. Common fix for compressor start issues. Basic repair in 15-30 minutes.

If your compact refrigerator won't start or stops running after a few seconds, the compressor overload protector may have failed. Moderate DIY repair.

This is a replacement mounting screw used to secure components inside compatible GE appliances. It restores proper fastening where the original screw is missing, stripped, or damaged so parts stay aligned and operate safely. What it does:

• Fastens trim panels, brackets, or internal components to appliance cabinet and chassis
• Replaces missing or damaged screws that can cause rattling, misalignment, or loose parts
• Helps maintain proper component alignment for reliable operation
• Simple hardware repair to restore original fit where the factory screw is lost or worn

• Verify screw size and thread match the original before installation
• Use correct driver to avoid stripping the head; tighten until snug but do not overtighten
• Disconnect power to the appliance before working near electrical components

This wire box houses and protects the appliance's power and wiring connections, keeping splices and the power cord terminal secure and insulated to reduce risk of shorts and electrical damage. What it does:

• Provides a protected enclosure for the main power connection and internal wiring splices
• Keeps wires organized and insulated to prevent contact with chassis or moving parts
• Helps prevent electrical arcing, sparking, and moisture exposure at the terminal area
• Restores a secure, strain-relieved connection when a damaged or missing box causes intermittent power or exposed wiring

• Disconnect power at the breaker or unplug the appliance before starting work
• Use proper strain relief for the power cord and secure the box to the cabinet per OEM instructions

This sealed component removes moisture and contaminants from the R600 refrigerant system, typically located in the sealed system behind the refrigerator. Replace if the refrigerator isn't cooling properly, runs constantly, or if a technician identifies refrigerant system contamination.

This display panel replaces the front console surface that houses the oven/range control and user interface, restoring visible readouts and button access for reliable programming and status feedback. It provides a clean, responsive face for the appliance controls. What it does:

• Replaces a cracked, faded, or non-responsive console surface so indicators and buttons are readable
• Restores visual status information such as temperature, timer, and clock displays
• Helps resolve issues where the face is damaged, buttons stick, or the display lens is obscured
• Works with the existing control electronics and keypad assembly to return normal user interaction

• Disconnect power to the appliance before attempting service to avoid shock
• May require removal of the control console and careful disconnecting of connectors or trim
• Handle the panel gently to avoid scratching the display lens or bending tabs

Replaces the exterior nameplate on your refrigerator door. Restores factory appearance when original badge is faded, cracked, broken, or missing.

Fix cooling issues in your refrigerator with this process valve. Regulates refrigerant flow for proper temperature control. Red cap design for R600 systems.