Parts for Ge GVS04BDWESS: Beverage Center Parts

This black refrigerator door gasket creates a tight seal around the door edge to help maintain consistent internal temperature and reduce energy loss. It replaces worn or damaged seals to help prevent frost buildup and food spoilage. What it does:

• Seals the door to keep cold air in and warm air out, preserving cooling performance
• Helps reduce frost and condensation inside the fresh-food compartment
• Limits compressor run time and energy waste caused by a leaking seal
• Common symptom: visible gaps, torn or flattened gasket material allowing cold air leakage

• Remove old gasket and clean the gasket channel before installing the new seal
• Work the gasket into the channel evenly, starting at corners and smoothing as you go
• Check for continuous contact around the door; slightly warm the gasket (hair dryer on low) if needed for final seating
• Follow refrigerator safety steps: unplug or disconnect power if required by your model before disassembly

This genuine replacement screw secures appliance panels and trim so parts stay aligned and rattle-free. It's a simple, low-cost fix that restores proper fit and prevents movement or vibration of covers and components. What it does:

• Fastens panels, trim, brackets, or components to maintain alignment and stability
• Stops rattling, vibration noise, and loose or sagging trims
• Helps ensure proper sealing and clearance where screws retain covers or housings
• Works wherever the OEM screw specification matches the original mounting point

• One replacement screw

• Use the matching screwdriver or bit to avoid stripping the head
• Turn slowly and stop when snug—do not overtighten to prevent thread or part damage
• Disconnect power or follow appliance-specific safety procedures before accessing internal parts
• Keep removed hardware organized so original placement can be restored

This interior oven lamp restores cavity lighting so you can check food without opening the door. It replaces a burned or flickering oven light to improve visibility while cooking. What it does:

• Illuminates the oven cavity so you can monitor cooking progress without opening the door
• Replaces a bulb that is burned out, dim, or flickering
• Helps prevent unnecessary oven door openings that can affect cooking results
• Matches the OEM form and fit for compatible GE ovens

• One oven lamp

• Disconnect power to the appliance before replacing the lamp to avoid electrical shock
• Allow the oven to cool completely before handling the lamp or reaching into the cavity
• Use care when removing/installing the lamp—handle by the base or use a cloth to avoid oils on the glass
• Only use the lamp wattage/type specified by your appliance manufacturer

This replacement glass shelf includes a molded front stop to keep items from sliding forward and help contain spills. It restores usable, level storage inside the refrigerator and is a direct-fit shelf replacement. What it does:

• Provides a sturdy, level surface for food and containers
• Molded front stop prevents items from sliding or tipping when the door opens
• Replaces broken, chipped or cracked glass shelf surfaces
• Helps reduce spills and keeps stored items organized
• Slides into existing shelf rails for a secure fit

• Remove food and containers before installing; handle glass with care and use gloves if damaged
• Slide shelf into the existing shelf rails until fully seated with the stop facing the front
• No wiring or tools typically required; if shelf doesn't seat smoothly, check rails for obstructions
• If the shelf is cracked or shattered, dispose of broken glass safely

This upper shelf is a direct-fit interior shelf designed to organize food and maximize usable space inside the refrigerator. It replaces a damaged or missing upper shelf so contents sit level and stay accessible. What it does:

• Supports food containers, produce bins, and other stored items on the refrigerator's upper section
• Restores a stable, level surface when an existing shelf is cracked, warped, or broken
• Helps maintain organized storage to prevent items from tipping or spilling
• Fits into the factory shelf supports for a secure hold when installed properly

• Remove food and any loose items from the refrigerator before replacing the shelf
• Slide the shelf into the factory tracks or supports until it seats firmly; do not force or bend
• Handle carefully to avoid dropping or chipping the shelf and to protect glass or plastic surfaces

This adjustable foot is a replacement leveling leg that supports the appliance and lets you raise, lower, and stabilize the cabinet for a proper fit. Simple, durable support that restores even weight distribution and alignment. What it does:

• Provides height adjustment to level the appliance on uneven floors
• Stabilizes the cabinet to reduce rocking or tipping
• Helps doors close and seal properly when unit is brought back to level
• Prevents floor damage by providing a replaceable contact point

• One adjustable foot/leveling leg

• Use with appliance empty or supported; follow manufacturer guidance for safely supporting the unit
• Raise or lower foot by turning to adjust height; check level and repeat as needed
• Wear gloves and eye protection when working under the appliance

A single replacement screw used to secure appliance panels, trim, or internal components. Restores proper fastening so doors, panels and mounts stay tight and aligned for safe, quiet operation. What it does

• Fastens trim, panels or brackets to the appliance chassis
• Replaces missing or stripped screws that cause loose parts or rattling
• Helps maintain proper alignment of doors and assemblies
• Prevents further wear or damage from unsecured components

• One screw

• Use the correct screwdriver to avoid stripping the head
• Do not overtighten; tighten until snug to avoid damaging threads or plastic
• Disconnect power or follow appliance safety procedures when working near electrical components

This bushing is a small replacement sleeve that supports and stabilizes a rotating or sliding shaft, helping restore smooth operation and reduce wear where a shaft passes through a housing. It prevents metal-on-metal contact and extends component life. What it does:

• Centers and cushions a shaft or pivot to prevent wobble and uneven wear
• Reduces noise and binding from worn or damaged bearing surfaces
• Protects housing and shaft from abrasion and scoring
• Helps restore proper alignment of moving components

• One replacement bushing

• Disconnect power to the appliance before beginning any repair
• Access may require removing panels, trim, or the component assembly; retain fasteners for reassembly
• Inspect mating shaft and housing for damage; replace if excessively worn
• Seat the bushing fully and test the mechanism for smooth operation before final reassembly

This is a replacement mounting screw used to secure components inside compatible GE appliances. It restores proper fastening where the original screw is missing, stripped, or damaged so parts stay aligned and operate safely. What it does:

• Fastens trim panels, brackets, or internal components to appliance cabinet and chassis
• Replaces missing or damaged screws that can cause rattling, misalignment, or loose parts
• Helps maintain proper component alignment for reliable operation
• Simple hardware repair to restore original fit where the factory screw is lost or worn

• Verify screw size and thread match the original before installation
• Use correct driver to avoid stripping the head; tighten until snug but do not overtighten
• Disconnect power to the appliance before working near electrical components

This wire box houses and protects the appliance's power and wiring connections, keeping splices and the power cord terminal secure and insulated to reduce risk of shorts and electrical damage. What it does:

• Provides a protected enclosure for the main power connection and internal wiring splices
• Keeps wires organized and insulated to prevent contact with chassis or moving parts
• Helps prevent electrical arcing, sparking, and moisture exposure at the terminal area
• Restores a secure, strain-relieved connection when a damaged or missing box causes intermittent power or exposed wiring

• Disconnect power at the breaker or unplug the appliance before starting work
• Use proper strain relief for the power cord and secure the box to the cabinet per OEM instructions

This grounding wire is an exact-replacement electrical ground connection used to restore a safe, reliable chassis/ground path on appliances. It helps reduce shock risk and ensures proper grounding for electrical components. What it does:

• Provides a dedicated ground path between appliance chassis and circuit ground
• Restores proper grounding after damage, corrosion, or during part replacement
• Helps stop intermittent electrical faults caused by a missing or loose ground
• Supports safe operation of switches, controls, and motors by maintaining chassis potential

• One grounding wire assembly

• Disconnect power before inspecting or replacing any electrical wiring
• Confirm mounting points and terminal orientation match the original before fastening
• Use appropriate hand tools; secure terminals and strain reliefs to avoid wire chafing
• Replace damaged components and verify ground continuity with a multimeter

This display panel replaces the front console surface that houses the oven/range control and user interface, restoring visible readouts and button access for reliable programming and status feedback. It provides a clean, responsive face for the appliance controls. What it does:

• Replaces a cracked, faded, or non-responsive console surface so indicators and buttons are readable
• Restores visual status information such as temperature, timer, and clock displays
• Helps resolve issues where the face is damaged, buttons stick, or the display lens is obscured
• Works with the existing control electronics and keypad assembly to return normal user interaction

• Disconnect power to the appliance before attempting service to avoid shock
• May require removal of the control console and careful disconnecting of connectors or trim
• Handle the panel gently to avoid scratching the display lens or bending tabs

Badge assembly that restores the exterior nameplate on compatible refrigerators, returning factory appearance and clear appliance identification. Ideal for replacing faded, cracked or missing emblems for a like-new finish. What it does:

• Restores the appliance's exterior identification and cosmetic finish where the original emblem is faded, cracked, or missing.
• Covers the mounting area and provides the finished look customers expect from the door surface.
• Matches factory styling so the appliance maintains a consistent, OEM appearance.
• Useful whenever visible badge damage detracts from the refrigerator's appearance.

• High-level surface-mount part—inspect the door surface and remove any old adhesive or residue before installing.
• Alignment is important; position carefully and press firmly to engage any snap-in tabs or adhesive backing.
• No electrical disconnection is typically required for exterior cosmetic badges, but avoid prying behind panels that expose wiring or components.