Black Max Lawn Mower Parts

Engine won't start after sudden stop? A sheared flywheel key breaks the connection between crankshaft and flywheel. Simple DIY repair.

This push rod kit is a genuine MTD part, sold individually. This push rod kit can be used as a replacement part in a lawnmower. This kit comes with a variety of push rods in various shapes and sizes, perfect for the replacement or repair of a push rod within the internal machinery of the lawnmower. The push rods could be dented, punctured, scraped, cracked, warped, or eroded, and if this occurs to the point of reduced or no efficacy, the push rod kit should be ordered as a genuine OEM replacement part.This is a genuine OEM replacement directly from the manufacturer. It is sold individually. This push rod kit is compatible with the following outdoor appliance brands: MTD, Bolens, Yard-Man, Yard Machines, Troy-Bilt, Cub Cadet, and Husky.

Seals and insulates the carburetor from engine heat on lawn mowers and outdoor power equipment. Replace if cracked, worn, or causing air leaks.

Seals the dipstick tube to prevent oil leaks in lawn mowers and tillers. Replace if oil seeps around dipstick or O-ring is cracked. Verify fit with model.

Starter rope won't retract after pulling? This recoil pulley and spring assembly fixes rope retraction issues on mowers and small engines. Direct fit.

Fuel filters are created to strain out gas before it reaches the carburetor in lawnmowers and other gardening tools. Located in the fuel line or the fuel tank, it prevents unwanted debris from reaching the carburetor, which can cause engine damage. If the fuel filter is damaged or becomes clogged with material, it no longer offers the same protection to the carburetor. This can lead to difficulty starting the lawnmower and decreased performance. Correcting this issue early can prevent damage that might require a new lawnmower. Maintenance of the lawnmower by adding fuel stabilizer, changing the oil, and replacing the air filter will increase the life of lawn care equioment. Even if no issues are present, the fuel filter should be replaced after about 200 hours of use. Disconnecting the spark plug should be done prior to installing a new fuel filter. This fuel filter is a genuine OEM component directly from the manufacturer and comes as an individual part. It can be used with various Craftsman, Cub Cadet, Murray, Yard Machines, MTD, Huskee, Bolens, Yard-Man, and Mastercut lawnmowers, tillers, blowers, and wood chippers.

Won't start or pull cord snapped? This recoil starter assembly engages the flywheel to start your mower, tiller, or chipper. Moderate DIY repair.

This genuine OEM Part is a choke temperature control rod for lawnmowers. The choke temperature control is the metal piece that regulates the choke temperature allowing for it to function properly within a lawnmower. If the choke function is no longer working efficiently, it might be time to replace the choke temperature control. Luckily, replacing this part is a simple repair.Before beginning, make sure the engine is cool to avoid getting burned. Locate the old choke temperature control rod and remove the screws to the mounting assembly that hold the rod in place. Once removed, lift the old choke temperature control out and away from the mower and set it to the side. Replace with the new control rod and secure the mounting screws. Start up the mower to see if the choke function is working properly. If it does, the installation was a success. This replacement part is sold individually and is compatible with MTD brand lawnmowers.

This choke temperature control gasket is an authentic OEM replacement part sourced directly from the manufacturer for use small engines that utilize a choke. The temperature control gasket helps to create a seal inside the choke that prevents air from seeping in or out of the choke. If the gasket is worn or damaged, air and contaminants could infiltrate the choke and cause the choke to fail. The choke temperature control gasket should be inspected and replaced if it is damaged. The choke uses a mixture of fuel and air to start the engine combustion process. If the choke temperature control gasket is not fully functioning, too much air could get in, and the ratio would not be optimal for the ignition process. If the engine is rough starting or starts and dies quickly, the choke's gaskets should be inspected and replaced as needed. Wear gloves when working on the choke and ensure that the spark plug is removed to prevent accidents.This choke temperature control gasket is sold as an individual part. It is designed for use in small engines that utilize a choke manufactured by MTD, Yard Machines, Yard Man, Cub Cadet, Husky, Troy-Bilt.

Carburetor assembly for walk-behind mowers and wheeled trimmers. Replaces cracked, damaged, or worn carburetors that affect fuel mixing and delivery.

This part is a carburetor gasket. A carburetor mixes fuel and air before delivering it to the engine. The carburetor gasket creates a seal between the carburetor and cylinder that ensures that air is where it's supposed to be.The carburetor gasket may need to be replaced if the seal is broken and it is allowing air in. If there is a slight leak, the operator may notice engine roughness when it's at idle. A larger leak will cause the engine to vibrate, misfire, or hesitate under acceleration. Remember to wear gloves when operating or performing care and maintenance on any outdoor power equipment machines.This part is a genuine MTD part and is an OEM part sourced directly from the manufacturer. It it is sold individually. This carburetor gasket is compatible with engines, lawnmowers, log splitters, and trimmers manufactured by MTD, Yard Machines, Yard-Man, Cub Cadet, Husky, and Troy-Bilt.

Fix engine misfires, rough idling, or starting problems. This spark plug restores reliable ignition in small engines. Simple DIY replacement part.

Prevents dirt, dust, and debris from entering your engine. Replace when dirty or clogged to maintain performance. Confirm fit with your model number.