Parts for Ge GFD65ESPN1SN: Blower & Motor Parts

The Motor Drive is an OEM part for GE dryers. It contains the electronic speed control board which regulates the power delivered to the dryer motor and drum. This precise control is crucial for properly tumbling and circulating heated air through clothes loads during dry cycles. 

Causes of a bad motor drive can include normal wear and tear over extended use, water or moisture damage corroding electronic components, or failure of individual parts such as capacitors or microchips.

Symptoms include:

• The dryer drum failing to rotate or tumble clothes
• Abnormal sounds, smells or heat coming from the motor 
• Cycles failing to initiate, complete, or progress properly
• Fault codes displayed or electrical issues

This OEM GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models. Proper operation of the motor drive helps ensure safe, dependable performance from your dryer.

The BLOWER WHEEL is an OEM part for GE electric dryers. It is housed within the blower motor housing and works to push air through the dryer ducting. During cycles, the rotating blower wheel creates crucial airflow that carries heated air through clothes to dry them efficiently.

Causes of a bad blower wheel can include cracked or broken wheel blades from normal wear and tear over time. Accumulations of lint on the wheel can also reduce airflow and efficiency.

Symptoms of a bad blower wheel include: 

• Insufficient or no air being pushed through the dryer ducting
• Abnormally long drying times and wet clothes after cycles  
• Excessive noise coming from the blower motor area
• Safety features possibly tripping due to motor overheating

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models. Maintain optimal airflow by replacing your blower wheel with this genuine OEM component.

A Belleville nut is a conical spring-style washer that provides axial tension and helps maintain a secure fastening under vibration and thermal cycling. It prevents fasteners from loosening so components stay mounted and aligned. What it does:

• Acts as a spring washer to keep bolts and studs under constant tension
• Helps prevent fasteners from backing out due to vibration or thermal changes
• Restores proper clamp force when a standard flat washer no longer holds
• Commonly used where a compact, high-load spring washer is required

• One Belleville nut

• Disconnect power to the appliance before servicing and follow all safety precautions
• Install on the correct fastener and seat the cone so it provides axial spring force
• Do not reuse if visibly deformed, corroded, or cracked
• Avoid over-tightening; snug to manufacturer torque specification when available

This resilient mount clip cushions and isolates appliance components to reduce vibration and noise while keeping parts aligned during operation. It's a direct-fit mounting clip used where a rubberized isolator is required. What it does:

• Absorbs and dampens vibration between chassis and attached components to help reduce noise
• Holds motor, blower or assembly securely in place to prevent misalignment and wear
• Helps keep attached parts from transferring shock to the cabinet during operation
• Commonly replaced when you notice increased vibration, rattling or loose-mounted components

• Unplug the appliance and disconnect power before any repair
• Support the component being removed to prevent it from falling or shifting
• Use basic hand tools; avoid over-tightening fasteners that can compress the isolator
• Inspect surrounding mounts and hardware and replace if worn or damaged

The Idler Spring is an OEM part for GE electric dryers. It is located within the drum assembly and provides the necessary rotational force during tumbling cycles.  

As a moving component, normal wear from repeated use can degrade the idler spring over time. Cracks, breaks, or loss of tension are potential causes of failure. 

Symptoms of a faulty idler spring include:

• Vibration noises emerging during cycles  
• Ineffective or reduced drum spinning for drying clothes
• Potential damage to other components from lack of support

Causes typically include normal wear and tear. Repeated heavy loads may accelerate component deterioration as well.

This genuine GE replacement spring restores proper tensioning to tumbling cycles. Compatible with some Hotpoint, RCA, and select Kenmore dryer models too, it improves stability and lengthens equipment life. Replacing a worn spring prevents ongoing operational issues.

The Drive Belt is an OEM replacement part for GE dryers. It is responsible for transferring rotational power from the dryer's motor to the drum, allowing it to spin during the drying cycle.

Symptoms of a faulty dryer drive belt include:

• Drum not spinning
• Unusual noises coming from the dryer
• Inability to start the drying cycle

A bad dryer drive belt can be caused by wear and tear over time or damage due to excessive tension, improper installation, or overloading the dryer. If you notice that the drum is not spinning or if you hear unusual noises during operation, it may be time to replace the old or damaged drive belt with this genuine OEM part.

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Idler Arm is an OEM component specifically designed for GE dryers. It is a vital part that helps transfer power from the motor to the tumbling action of the dryer drum. The idler arm assembly allows the belt to provide smooth, consistent power to operate the drum efficiently during each cycle.  

Symptoms of a bad idler arm assembly include:

• Squealing or grinding noises coming from the dryer motor or drum area
• The dryer drum not rotating or spinning slowly
• Loose, cracked, or worn idler pulley
• A worn or slipping dryer belt 

Causes of failure can be normal wear and tear over extended use. Excess vibration from an unbalanced load or a dropped object inside the dryer could also potentially damage the idler arm.

This part is compatible with Hotpoint, RCA, and Kenmore dryer models.

This motor gasket is a molded sealing pad that cushions and seals the motor assembly to the appliance chassis, helping reduce vibration and protect the motor from debris and moisture. Replacing a worn gasket restores proper motor alignment and quieter operation. What it does:

• Cushions and isolates the motor to reduce vibration and noise during operation
• Seals the motor mounting area to help prevent dust, lint, and moisture intrusion
• Helps maintain correct motor alignment to avoid rubbing or premature wear
• Commonly replaced when torn, flattened, or degraded and causing excess vibration or noise

• One motor gasket

• Disconnect power (unplug or shut off breaker) before starting any repair
• Requires partial appliance disassembly to access the motor; follow OEM service instructions
• Inspect surrounding mounting hardware and motor for damage while replacing the gasket
• Do not use adhesives or improvised fasteners unless OEM instructions specify

This fan seal cushions and centers the fan on the motor shaft to reduce wobble and protect the motor and fan assembly from wear. It helps maintain smooth fan operation and can reduce vibration and noise when worn parts are replaced. What it does:

• Centers the fan on the motor shaft to prevent rubbing and uneven wear.
• Cushions the fan to reduce vibration and noise associated with a loose or damaged seal.
• Protects the motor shaft and fan bore from metal-on-metal contact.
• Common symptom: visible wear, fan wobble, scraping noise, or increased vibration.

• Designed for use on specified GE appliance fan/motor assemblies.
• Turn off and disconnect power to the appliance before attempting service.
• Inspect the fan and motor shaft for damage; replace worn components as needed for proper fit.
• If removal requires disassembly of panels or brackets, keep fasteners organized and follow OEM service steps.

The Thermostat is an OEM part for GE dryers. It monitors air temperatures inside the dryer drum during cycles to ensure they remain within a designated safe range. As a safety component, the thermostat automatically cuts power if temperatures get too high, protecting dryer components from damage.

Causes of a bad thermostat can include normal wear and tear over time from repeated heat cycles. Mineral buildup interference or electrical faults may also cause premature malfunction.

Symptoms of a faulty thermostat include:  

• Inability to properly heat or maintain consistent air temperatures
• Unexpected fluctuations outside of set temperature points   
• Issues fully completing designated drying cycles  
• Potential overheating errors or safety trips

This genuine OEM GE replacement thermostat restores accurate temperature monitoring and controls. Compatible with some Hotpoint, RCA, and Kenmore models as well, it improves performance reliability and safety once installed.

This outlet thermistor monitors exhaust air temperature in the dryer's outlet duct and reports it to the control. Replacing a faulty sensor helps restore accurate heat regulation, preventing over- or under-drying for consistent drying performance. What it does:

• Measures outlet/exhaust air temperature and sends a resistance signal to the control board
• Helps the control cycle the heater or burner on/off to maintain proper drying temps
• Failure symptoms can include long dry times, no heat, overheating/shutting off, or inconsistent temperatures
• May illuminate a sensor-related error on models with diagnostics

• 1 outlet thermistor

• Disconnect power; shut off gas supply for gas models before servicing
• Access the exhaust/outlet duct or blower housing (location varies by model); the thermistor mounts on this duct
• Note wire locations, remove the fastener/clip, transfer any bracket if present, and install the new sensor with its tip in the airflow; secure connections
• Reassemble and run a test cycle to proper heat cycling

Size: 8 - 18 ab.