Parts for Broan K210A48SS: Blower P8 Parts

Range hood adapter component for connecting duct sections or transitioning between sizes. Replaces cracked, damaged, or missing adapters in venting systems.

This is a vent damper designed for use with a range hood exhaust system. It mounts in the ductwork and uses a gravity or spring-loaded flap to allow air to flow out while preventing outside air, drafts, and pests from entering when the hood is off. Replace this part if you notice cold drafts coming through the hood vent, the damper flap is stuck, or the existing damper no longer seals properly.

Directs exhaust airflow and shields internal blower from grease buildup. Replace if venting is weak or noisy. Verify fit with your model number.

This retaining nut secures components on ventilation and range hood assemblies to restore proper fit and reduce movement. A small but essential fastener used where vibration or threaded connections need a reliable hold. What it does

• Secures fan, grille or mounting hardware to threaded studs or bolts
• Keeps assemblies tight to prevent rattling or loosening over time
• Helps maintain correct alignment of venting components
• Prevents parts from separating during normal operation

• One retaining nut

• Disconnect power to the appliance before servicing electrical or moving parts
• Match thread size and type before installation; start by hand to avoid cross-threading
• Use the correct wrench/socket and tighten snugly without over-torquing
• Replace damaged or stripped nuts to ensure secure fastening

Range hood fan won't start or runs weak? A faulty capacitor often causes these issues. This part stores electrical charge to power the motor efficiently.

Range hood not venting smoke or odors? This direct-drive blower motor restores proper airflow by powering the ventilation fan to clear cooking fumes.

Blower wheel for range hood ventilation systems. Mounts on the motor shaft to pull air through the filters. Replace if cracked, damaged, or missing.

Range hood not venting smoke or steam? A failed blower motor stops air circulation. This motor restores ventilation power in compatible vent hoods.

This flat washer provides a stable bearing surface for fastening hardware, helping distribute load and reduce wear on the mating parts. It's a small replacement that restores proper spacing and secure assembly where a washer is required. What it does:

• Sits under a nut or screw head to spread clamping force and protect the part surface
• Helps maintain correct spacing between components and prevents hardware from digging in
• Reduces loosening from vibration when used with the correct fastener
• Commonly used in appliance assemblies where a metal-to-metal bearing surface is needed

• Power off and unplug the appliance before accessing internal components
• Confirm this is the correct washer for your application by matching the part number on the old part
• Position the washer flat under the fastener head or nut; do not stack unless specified
• Tighten fasteners to a snug fit—avoid over-tightening, which can deform the washer or the assembly

Excessive rattling or vibration from your range hood? This rubber grommet cushions motor mounts to eliminate noise and metal contact. Simple DIY fix.

This replacement screw secures panels and components in range hoods and ventilation products, restoring a secure fit and reducing rattling or loose parts. Use it to replace missing or damaged fasteners for a snug, reliable hold. What it does:

• Secures access panels, trim, or mounting brackets to prevent movement and vibration
• Replaces missing or stripped screws that cause loose or rattling parts
• Restores proper alignment for covers and assemblies
• Compatible with the original fastening points for a direct fit when the correct screw is required

• Disconnect power to the appliance before performing any service
• Use the correct-size screwdriver or bit to avoid stripping the head
• Do not overtighten; snug until secure to prevent damage to parts or threads
• Keep removed hardware and note orientation for reassembly

Power cord for range hood and vent systems. Connects your ventilation unit to electrical outlet. Replace if cord is frayed, damaged, or missing.

Power cord for range hood vent systems. Replaces damaged, frayed, or missing electrical cords. Restores safe electrical connection to your unit.

This genuine replacement mounting screw secures range hood and ventilation components so panels and brackets stay fastened. Replacing a missing or worn screw restores proper alignment and reduces vibration or rattling. What it does:

• Secures panels, brackets, or small assemblies to the hood or vent body
• Keeps components aligned to prevent vibration and noise
• Helps maintain a tight electrical and mechanical connection where used
• Prevents parts from loosening or falling during operation

• Verify screw size and thread match the original before installation
• Hand-start threads and use the correct screwdriver to avoid stripping
• Tighten until snug; avoid over-tightening which can strip threads or crack plastic
• Disconnect power to the appliance if working near electrical components