Parts for Weedeater EBV210 TYPE 2: Blower Parts

This is a screw designed to be used in many types of lawn and garden equipment. The screw can be used in several locations but is most commonly located in a place where it can secure the trigger housing or the two sides of a handle. Screws can be used on their own or with a nut using a pre-drilled hole. If a nut is going to be used, it should have the same threading and finish as the screw.A screw can be damaged or broken and will need to be replaced. High temperatures, corrosion, and stress can cause the screw to break. Due to its small size, a screw may also be easily lost during other repairs. A visual inspection will provide information about whether the screw is broken, stripped, or lost. If any of these things are true, the screw should be removed using a screwdriver. A bolt remover can be used to replace the screw if it has become stripped.This screw is a genuine OEM replacement component that is directly sourced from the manufacturer. It is sold as a single screw. The screw is designed to be used with string trimmers, pole pruners, and leaf blowers manufactured by Paramount, Weed Eater, Craftsman, Poulan Pro, and Poulan.

This authentic OEM replacement wire harness is an assembly of various wires needed to operate a leaf blower engine. Leaf blowers have many parts that send an electrical current to create the desired effect—for example, the throttle. This current travels through a wire and switch to generate a response. If the wires become damaged, they will no longer transfer a signal. This harness is a replacement set containing a switch, cables, and terminals. One of the most common causes of damaged wiring is overheating. If the electrical current traveling through the wires suddenly fluxes, the wires can be fried, causing the leaf blower to stop functioning. When this happens, the wires will have to be replaced before the blower can be used again. This is a straightforward repair and will only require a screwdriver. Be sure to follow the user's manual and make note of where each wire goes. This is a high-quality replacement part sourced from the original manufacturer and is designed to be used with Weed Eater, Paramount, Poulan Pro, Husqvarna, and Craftsman leaf blowers. It ships separately of any additional hardware.

This replacement part is a motor assembly. This part is commonly found in leaf blowers and is a complete motor, which allows the equipment to run.A new motor assembly might be needed if the current one is no longer working as during prior uses. If the motor is no longer operating correctly, it might be time to replace this part. If the equipment is no longer working or has trouble starting, it can be due to a faulty motor. Work gloves are always recommended when replacing this part to ensure safety.This is a genuine OEM replacement part manufactured by Husqvarna. This part is sold individually.

This OEM replacement part is an inlet restrictor tube for leaf blowers. The inlet restrictor fits into the air inlet and is used to improve blower function. If the leaf blower is no longer functioning like it used to and is struggling to maintain its power, it might be time for a new inlet restricor tube. While this might seem like a difficult repair, replacing this part is actually a very simple process.To replace the inlet restrictor tube, make sure the engine is cool and the on off switch is in the off position. Remove the main tube from the leaf blower. Then locate the inlet restrictor tube at the base of the leaf blower. Using a flathead screwdriver, pry off the old inlet restricor tube and set it to the side. Slide the new tube into place and reinstall the main tube. This genuine OEM part is compatible with Husqvarna leaf blowers.

This vacuum bag is a genuine OEM replacement for select leaf blower/vacuum models. The bag attaches to the shaft and catches clippings, leaves, and other debris when the machine is used in vacuum mode. This canvas bag is made of durable material, but it can wear down with regular use and exposure to the elements. If the bag tears or wears thin and can no longer hold clippings, it will need to be replaced. In some cases, the carrying strap or zipper on the bag may break, which will also necessitate a replacement. This genuine OEM part can provide the exact fit for compatible blowers. This OEM bag replacement is manufactured to strict standards and will work with various machines from Craftsman, Weed Eater, Poulan, and Jonsered. This bag is made of heavy-duty fabric and requires no tools for installation. The velcro strap to secure the bag is not included with this listing, so if a replacement strap is needed it will have to be purchased separately. This bag is sold as an individual unit.