Parts for Bosch WTMC8530UC/06: Body / Door Parts

This back panel is the replacement rear cover that protects the appliance's internal components and wiring from debris and damage. It restores the unit's exterior protection and helps reduce noise from loose or exposed parts. What it does

• Covers and shields internal components, wiring and connections at the appliance rear
• Helps prevent debris, pet access and accidental contact with electrical parts
• Reduces rattling or vibration caused by a missing or damaged rear cover
• Maintains proper airflow routing and enclosure integrity for safe operation

• One back panel

• Disconnect power (unplug or shut off breaker) before starting any work
• Use appropriate tools to remove fasteners; keep original screws and mounting hardware if present
• Handle edges carefully — metal panels can be sharp
• Note or photograph locations for reassembly

The Screw is an OEM part for Bosch microwave ovens. It is a component that secures the outer casing and front paneling of the microwave. The screw is designed to withstand repeated heating and cooling cycles without loosening or degrading. 

Symptoms of bad screw include:

- The front panel or outer casing becoming loose, detached, or misaligned
- Gaps appearing in the seams or joints of the microwave structure
- The door not sealing properly leading to leaks

Over many uses of the microwave, screws can wear down or strip out from over-tightening during repairs or installations. It is important to replace worn screws to ensure the microwave maintains an intact structure.

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.
 

The Foot is an OEM component specifically designed for select Bosch vented dryers requiring balanced tumbling motions. As an anchor point, it supports revolving drum weights during operation.

Causes requiring replacement relate to cumulative use wearing down attached glides and compromising smooth rotations. Physical damage exposing reinforcement fibers risks accelerated failure. 

Symptoms signaling the need for a new foot involve:

• Shaking or off-balanced drum movements from failed supports
• Loosened fasteners enabling unintended dislodging or displacement
• Cracked housings no longer stabilize intended weight distributions

This OEM Bosch replacement foot is also compatible with Thermador, Gaggenau and select Kenmore dryers relying on anchored rotational components. Correct installation restores intended weight balancing.
 

This Cap is a small protective closure used to cover and protect exposed openings or fittings on compatible Bosch appliances, helping keep dirt and moisture out for reliable operation. What it does:

• Covers exposed openings, ports, or fasteners to prevent debris and moisture intrusion
• Helps maintain proper alignment and protection of small components
• Stops small leaks or drips when used as a sealing closure in low-pressure areas
• Useful when the original cap is cracked, missing, or worn

• One replacement cap

• Install by snapping or pressing into place; no special tools typically required
• If the cap is near electrical components, disconnect power before replacing
• Replace if cracked or deformed to restore proper protection

The Door Hinge is an OEM part for Bosch dryers. This hinge is designed to securely attach the dryer door to the frame, allowing it to open and close smoothly while maintaining a proper seal during operation.

Causes of a bad door hinge can include regular wear and tear, damage from excessive force when opening or closing the door, or corrosion from exposure to moisture and heat.  

Symptoms of a bad door hinge include:

• The dryer door not closing properly or staying open
• Difficulty opening or closing the dryer door
• A misaligned dryer door
• Unusual noises or resistance when moving the door

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.

Replacement mounting screw that secures panels, brackets and trim on compatible Bosch appliances. Restores proper fastening to reduce rattling, loose parts and alignment issues for safer, quieter operation. What it does:

• Secures panels, brackets, trim pieces and small appliance components.
• Replaces missing, stripped or corroded screws that allow parts to vibrate or become misaligned.
• Helps restore proper fit and reduces noise caused by loose or shifting components.
• Used wherever the original screw fastens service panels or mounting brackets.

• Disconnect power to the appliance before beginning any repair work.
• Use the correct driver bit to avoid stripping the screw head; apply firm, steady pressure.
• Do not overtighten—tighten until snug and parts are secure to avoid damaging threads or components.
• If original threads are damaged, inspect mating component and replace damaged parts or use appropriate thread repair methods.

This factory fastener secures appliance components and panels so they stay aligned and quiet. Replacing a missing, stripped, or corroded screw restores a tight fit and helps prevent vibration, rattling, and premature wear.

• Secures brackets, covers, panels, or internal parts per your model's design
• Helps maintain alignment and reduce vibration/noise during operation
• Replaces lost, stripped, rusted, or damaged hardware
• Common signs include loose or shifting panels, rattling sounds, or a missing screw found during service

• Disconnect power before servicing; shut off water or gas if applicable to your appliance
• Match the screw to the original location/length; replace one at a time to avoid mix-ups
• Start threads by hand to prevent cross-threading; tighten snugly without overtightening
• Use the correct driver for the head type on your model to avoid stripping

The Door Latch is an OEM part for Bosch dryers. It securely fastens the dryer door closed during operation to prevent heat loss and ensure optimal drying performance. 

Causes of a bad latch include wear and tear over time, damage due to repeated use, or failure of the latch mechanism. 

Symptoms of a bad door latch include:

• The door not fully closing or latching in the locked position
• The door popping or coming open during a cycle  
• Decreased drying efficiency due to air leaks
• Safety issues from an unsecured door

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.

This replacement trim strip restores the appliance's finished edge and helps cover gaps or fastener holes for a clean, factory appearance. It's a simple cosmetic part that brings worn or damaged trim back to neat condition. What it does:

• Covers exposed edges or fasteners to improve the appliance's appearance
• Restores missing or damaged trim that can catch dirt or moisture
• Helps maintain a finished look after repairs or panel replacement
• Fits where the original decorative/edge strip was installed

• One trim strip

• Basic installation; often snaps or screws into place—inspect mounting points before installing
• Turn off and unplug the appliance if working near electrical components
• Use appropriate trim fasteners; do not force the strip into place to avoid damaging panels

This replacement trim strip restores the finished edge and helps protect the appliance cabinet or panel from chips, gaps, and wear. It's a direct-fit cosmetic and protective strip used where the original edge or trim has failed. What it does:

• Covers and protects exposed panel edges to prevent chipping and hide damage
• Restores a clean, finished appearance after wear, cracking, or loss of the original strip
• Helps keep panels aligned and reduces gaps that trap dirt and moisture
• Safe symptom language: replace if strip is cracked, missing, loose, or cosmetically damaged

• High-level: remove any damaged strip and clean the mounting surface before installing the new strip
• Many strips snap or slide into place; light tools (flat screwdriver, trim tool) may be helpful
• Always disconnect power to appliances with electrical components before performing service
• If mounting hardware is present on the original, transfer it to the new strip if appropriate

The Screw is an OEM part for Bosch gas cooktops and ranges. It anchors the surface burner head assembly onto the cooktop surface.

Causes can be stripped threads or overall wear from repeated heating/cooling cycles. Exposure to cooking spills or impacts may also deteriorate the screw head over time.

Symptoms of a bad burner head screw include:

• A burner detaching from the cooktop surface entirely
• Excess movement or instability of burner heads when in use
• Gas leaks reported around the burner head connection points

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

This is a factory-style screw used to secure appliance panels and components for a reliable, low-profile hold. It replaces worn or missing fasteners to stop rattling and keep parts aligned during normal use. What it does:

• Secures trim, panels, brackets or small components in place
• Stops loose parts that can cause rattling or vibration noises
• Restores correct fit where a missing or damaged screw allows gaps
• Works as a direct replacement when the original fastener is lost or stripped

• One screw

• Disconnect power and water before servicing the appliance
• Start the screw by hand to avoid cross-threading; use the correct driver bit
• Tighten snugly but avoid over-torquing to prevent stripping or part damage
• Keep removed hardware organized to ensure correct reassembly