Parts for Electrolux FFGF3047LSJ: 04 - Body Parts

Side panel for gas ranges. Replaces cracked, dented, or damaged exterior panels. Restores the structural integrity and appearance of your range.

Control panel trim for electric and gas ranges. Replaces cracked, faded, or damaged panel trim. Installs on the front control area to restore appearance.

Exterior trim panel that houses and protects your range's control interface and display. Replace if cracked, broken, or worn to restore a clean appearance.

Maintop bracket secures the cooktop surface to the range frame. Replace if cracked, bent, or broken to restore proper alignment and support.

This factory screw secures panels, brackets, and other components in your cooking appliance. Replace a missing, stripped, or corroded fastener to restore a tight, rattle-free fit and keep parts properly aligned during use.

• Fastens components to maintain proper alignment and stability
• Helps prevent vibration, rattling, and loose parts during operation
• Replace if threads are stripped, the head is damaged, or the screw is missing
• Commonly used to mount internal or exterior parts in ranges and wall ovens

• Disconnect power and allow the appliance to cool; shut off gas supply if applicable
• Use the correct driver bit to avoid stripping the screw head
• Install in the original location and do not overtighten
• If the receiving threads are damaged, repair or replace the mating part before installation

Leveling leg assembly installs at the front corners of your range. Replace if broken, rusted, missing, or no longer adjusts to level your appliance.

Replace your cracked, warped, or hard-to-clean oven rack. This durable rack installs inside your range oven to support cookware during baking and roasting.

This drain pan collects and channels condensation away from the evaporator to prevent water buildup and leaks. It restores proper drainage and helps maintain refrigerator hygiene and consistent operation. What it does:

• Catches defrost and condensation water from the evaporator coil to prevent pooling inside the cabinet
• Directs water toward the drain tube or pump for proper removal
• Helps reduce unwanted odors and potential mold by containing moisture
• Supports the evaporator assembly and aligns with mounting points for a secure fit

• One drain/evaporator drip pan as shown

• Inspect surrounding seals and the drain tube for clogs before reinstalling the pan
• Use basic hand tools; keep electrical power disconnected when accessing internal compartments
• Handle carefully to avoid bending mounting tabs or damaging nearby components
• Replace any damaged fasteners or gaskets removed during service

This insert is a small trim piece designed to restore fit and finish on your appliance where factory trim has worn or been damaged. It improves appearance and helps protect edges from wear. What it does:

• Replaces a damaged or missing trim insert to restore original appearance
• Covers gaps and provides a finished edge on the appliance component
• Helps prevent dirt and moisture from reaching underlying parts
• Supports proper alignment of the surrounding trim or panel

• One insert trim piece as pictured

• High-level replacement; may require removal of surrounding trim or fasteners
• Use appropriate hand tools and keep small parts organized during reassembly
• Disconnect power to the appliance before starting work if removal involves electrical components

Oven light not working or saw a flash near the bulb? This light socket houses the oven bulb and is a straightforward DIY fix in under 30 minutes.

The Light Bulb (40W) is an OEM part for Frigidaire appliances. Specifically designed to fit and function with Frigidaire models, this 40-watt bulb illuminates the interior of your oven, making it easier to check on the progress of your baking or roasting without opening the oven door.

Over time, oven light bulbs can burn out or be damaged from high temperatures or accidental bumps during cleaning or cooking. A functioning light bulb is crucial for the optimal operation of your oven, enhancing visibility and improving your cooking experience.

Symptoms of a bad Light Bulb include:

• The oven interior remains dark when the light switch is engaged.
• Flickering light, indicating a loose connection or nearing the end of the bulb's lifespan.
• Completely non-functional light, which can hinder your ability to monitor cooking progress.

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

Secures cabinet panels to your range frame, maintaining proper alignment and structural stability. Replace if bracket is cracked, bent, or missing.

Mounting bracket for electric and gas ranges. Secures components in place. Replace if bent, cracked, or broken to restore proper fitment and stability.

Replace your gas range flue gasket to seal the flue opening and prevent heat loss. Install when worn, cracked, or damaged. Confirm fit with model number.

Flue for gas ranges. Vents hot air from the oven cavity to the cooktop surface. Replace if cracked, damaged, or missing to restore proper ventilation.

Fixes oven not reaching correct temperature or displaying error codes. This temperature sensor probe monitors and regulates oven heat. Easy DIY fix.

Secures the oven bottom panel in place. Replace if screw is stripped, missing, or no longer holds the panel securely. Sold individually.

Fiberglass insulation panel that installs behind the oven cavity. Replaces missing, damaged, or rodent-chewed insulation to restore heat containment.

This electrical receptacle is the small connector that secures a wiring plug to an appliance component, restoring a reliable electrical connection and preventing intermittent operation or arcing. What it does:

• Provides a secure plug-in connection between a wire harness and a component
• Restores power to a component when the original connector is cracked, melted, or corroded
• Helps prevent loose connections that can cause intermittent operation or sparks
• Fits the OEM-style wiring configuration for a direct replacement

• Disconnect power to the appliance before starting any repair
• Remove the damaged connector and match the replacement to the harness before installing
• Use basic hand tools; avoid forcing terminals to prevent damage

Metal shield that protects the oven ignitor assembly from spills, drips, and debris. Replace if cracked, bent, damaged, or missing to restore protection.

Anti-tip bracket kit secures your range to the floor or wall, preventing tipping when the oven door is opened or heavy cookware is placed on extended racks.

Replacement screw for electric and gas ranges. Used to secure various components and panels. Order a new screw if the original is stripped, missing, or damaged.

The Block is an OEM part for Frigidaire electric ranges. Located at the rear of the oven cavity, the block acts as the foundation that securely mounts and supports various range components, such as the bake and broil heating elements. Crafted with rugged insulation materials, the block withstands extreme temperatures produced during baking and broiling. 

Causes of a bad block can include cracks or fissures developed from repeated heating and cooling, melted or charred areas burned by cooking spills, or damaged mounting points no longer securely holding components in place.

Symptoms of a bad block include: 

• Elements that do not heat properly or uniformly
• Loose, rattling, or misaligned internal parts  
• Odors or sparks witnessed during oven use
• Inability of the oven to reach or maintain set temperatures

This Frigidaire OEM replacement restores a sturdy foundation for safe, dependable cooking performance. Compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This is a replacement mounting screw used to secure the dual safety valve assembly on compatible gas ranges and ovens. It restores proper fastening so the valve stays firmly in place during operation. What it does

• Secures the safety/dual gas valve to the appliance chassis or manifold
• Prevents valve movement that can interfere with burner operation or alignment
• Commonly replaced when original screw is missing, stripped, or damaged
• Matches OEM thread size and length for correct fit and retention

• One (1) screw, size 10-16 x 0.486

• Disconnect power and shut off gas supply before starting work; follow all safety procedures
• Thread carefully to avoid cross-threading; do not overtighten — snug to OEM torque specification
• Inspect surrounding mounting holes and hardware; replace any stripped or damaged parts for a secure fit

Support plate that mounts to the bottom of your range oven cavity. Replace if the original plate is cracked, warped, or damaged from heat exposure.

Replacement mounting screw for ovens and ranges. Secures panels, brackets, trim, and internal components. Replace missing or stripped screws to restore fit.

Mounting screw for securing range panels, brackets, and igniters. Replace if stripped, missing, or damaged to restore proper fastening and alignment.

The Range Harness is an OEM replacement part for Frigidaire gas ranges. It is an electrical wiring harness that connects power to the various control boards and heating components within the appliance. 

Symptoms of a bad range harness include: 

• Intermittent or complete loss of power to heating elements
• Failure of electronic displays and controls to operate properly  
• Buzzing or humming noises coming from inside the appliance
• Burning smells or signs of overheating in the wiring

Causes can be cracking, pinching or chafing of wiring over time due to normal use and repeated movement of the appliance. Accidental cutting or puncturing of cables during cleaning is also possible.

This OEM replacement harness is compatible with Electrolux, Gibson, Kelvinator, and some Kenmore models as well.

Chrome screw secures handles, door trim, and internal components in ranges and ovens. Replace if lost during cleaning, stripped, or missing after moves.

Chrome screw secures handles, door trim, and internal components in ranges and ovens. Replace if lost during cleaning, stripped, or missing after moves.

Anti-tip bracket kit secures your range to the floor or wall, preventing tipping when the oven door is opened or heavy cookware is placed on extended racks.

Anti-tip bracket kit secures your range to the floor or wall, preventing tipping when the oven door is opened or heavy cookware is placed on extended racks.