Parts for Electrolux FFGS3025PSE: 04 - Body Parts

Control panel for electric and gas ranges. Installs on the front to house buttons and display. Replace if cracked, chipped, discolored, or damaged.

This shield is a molded protective cover that guards internal components from debris and helps direct airflow inside the appliance for reliable operation. It replaces a damaged or missing cover to restore component protection. What it does:

• Protects internal parts from dust, debris and incidental contact
• Helps maintain correct airflow routing around components
• Reduces risk of rattles or contact-related damage from loose parts
• Useful when the original shield is cracked, broken or missing

• Disconnect power and, if applicable, water before beginning any repair
• Remove access panels or components as needed to reach the mounting location
• Handle edges carefully; some shields may have sharp edges or tabs
• Reuse existing fasteners unless the OEM instructions specify replacements; follow manufacturer guidelines

Replacement control panel for your range. This front panel houses controls and display. Needed when the original panel is cracked, damaged, or worn.

Screw that adjusts and secures the leveling leg to your range base or bracket. Replace if stripped, bent, or missing to restore stable footing and level your appliance.

Broiler pan for electric and gas ranges. Installs in oven cavity for broiling. Replace if cracked, warped, rusted, or heavily stained beyond cleaning.

This broiler insert is the oven pan insert that sits under the broiler burner to catch drips and help direct heat for even browning. It restores a stable cooking surface and keeps the broiler area cleaner. What it does:

• Holds food and catches grease and drips during broiling to prevent mess and flare-ups
• Directs heat from the broiler for consistent browning and searing
• Replaces damaged, warped, or corroded inserts that cause uneven cooking
• Helps prevent food from falling into the burner area

• One broiler insert

• Disconnect power to the appliance and allow the oven to cool completely before servicing
• Remove oven racks and slide the old insert out; position the new insert so it seats securely in the broiler cavity
• Wear heat-resistant gloves when testing the broiler after installation and inspect for proper fit before use
• Do not modify the part; use only as designed for the oven broiler assembly

This is a flexible gray gasket that lines the perimeter of the oven door to create an airtight seal when the door is closed. It prevents heat from escaping the oven cavity, helping maintain consistent cooking temperatures. Replace this seal if you feel excessive heat radiating from around the oven door, notice uneven cooking, or see visible wear, cracks, or gaps in the existing gasket.

This is a door-activated switch that detects whether the oven door is open or closed. It controls functions such as the oven light or signals the control board about door position. Replace this switch if the oven light stays on or off regardless of door position, or if the oven does not operate correctly due to a faulty door signal.

The Range Lamp Assembly is an OEM part for Frigidaire stoves and ranges. It consists of the halogen light bulb, lens cover, and wiring harness necessary to illuminate the oven cavity. This lamp assembly provides light to the cooking and baking space, making it easier to view food and monitor cooking progress.  

Symptoms of a bad range lamp assembly include:

• The oven light not turning on at all  
• Dim, flickering, or intermittent light
• Burned out or blown light bulb
• Cracks or damage to the lens cover

Causes of failure can be a burned out light bulb, broken wiring, or damage from impact or heat over time. 

This OEM Frigidaire replacement part is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This is an interior cover panel for an oven or range. It shields internal components from heat, grease, and food debris during cooking. Replace this cover if it is cracked, warped, or damaged, which could expose internal parts or affect the oven's ability to maintain proper temperature.

Replace a cracked, broken, or missing oven door spacer that maintains proper alignment and gap between door components. Installs in door assembly.

This control panel is the exterior console assembly that houses the oven/range controls and user interface, restoring a clean, functional front for the appliance. It provides the mounting and button/label surface for the range's control electronics. What it does:

• Provides the visible control surface and mounting for push-buttons, switches, and display components
• Restores labeled buttons and control access if the original panel is cracked, faded, or warped
• Helps protect underlying electronic components from spills and debris when intact
• Commonly replaced when buttons stick, labels wear off, or panel is physically damaged

• One control panel (console) as pictured

• High-level replacement; remove power (unplug or trip breaker) before starting
• May require removal of range trim, bezels, and disconnecting control harnesses; keep fasteners organized
• Handle gently to avoid scratching painted/printed surfaces; verify alignment before tightening

Oven won't reach or hold set temperature? A faulty temperature sensor causes inaccurate heating. This monitor probe ensures consistent cooking results.

Replacement power cord for ovens and ranges. Installs at the rear panel to restore electrical connection. Needed when original cord is frayed or damaged.

Stamped protective mounting panel that shields internal components and wiring in your gas range. Replace if yours is cracked, bent, broken, or missing to secure parts.

Secures the oven bottom panel in place. Replace if screw is stripped, missing, or no longer holds the panel securely. Sold individually.

Replace a cracked, broken, or missing outer housing cover on your range. This trim piece protects internal components and restores the finished look.

Insulation panel that installs inside your range oven door to maintain heat efficiency. Replace if cracked, compressed, deteriorated, or missing.

Insulation panel for gas ranges. Installs inside the range cavity to provide sound dampening and thermal protection. Replace if torn, damaged, or missing.

Heat shield for ranges and wall ovens. Protects internal components from excessive heat. Replace if cracked, warped, or damaged to prevent overheating.

Receptacle for electric and gas ranges and wall ovens. Installs as a connector component. Replace if cracked, damaged, or missing to restore proper fit.

If your oven isn't heating evenly or the convection fan isn't working, this motor restores proper airflow. Moderate difficulty repair in 30-45 minutes.

This is a black filler panel designed to mount on the left side of the range. It covers the gap between the range and adjacent cabinetry for a finished, built-in appearance. Replace this panel if it is cracked, warped, discolored, or missing.

Fix loud rattling or grinding noise from your oven fan. This convection fan motor restores quiet operation and even heat distribution. DIY repair.

The Thermostat is an OEM component specifically designed for Frigidaire gas stoves. This thermostat controls burner temperatures by regulating gas flow. 

Causes of a bad thermostat include wear and tear over time, overheating, moisture damage, or power surges that can degrade electrical components.

Symptoms of a bad thermostat include:

• Inability to control burner temperatures accurately 
• Burners heating to excessively high or low levels
• Fluctuating burner output unrelated to dial settings
• Complete failure of one or more burners to light

Replace it today with this OEM Frigidaire part to maintain safe and reliable stove operation. This thermostat replacement is also compatible with Gibson and Kelvinator gas ranges, as well as select Kenmore models. 

Secures internal components to your range cabinet. Replace this bracket if the original is broken, bent, or missing to restore proper alignment.

Range anti-tip bracket kit prevents tipping hazards. Install during range setup or if missing. Includes brackets and mounting screws. Verify fit.

Structural frame component for electric and gas ranges. Replaces damaged, bent, or corroded frame that affects cabinet integrity or appliance stability.

Replacement mounting screw for range power and control boards. Secures electrical board connections. Needed when original screw is missing or damaged.

This is a metal mounting bracket used to secure an over-the-range microwave to the wall or cabinet during installation. It provides structural support and helps keep the microwave properly aligned and stable. Replace this bracket if it is bent, broken, or missing, which can cause the microwave to sit unevenly or become unsafe.

Mounting screw for electric and gas ranges. Secures internal components and panels. Replace if stripped, missing, or damaged during appliance maintenance.

Fix intermittent power or control issues in your gas range with this wiring harness. Restores electrical connectivity between components. DIY repair.

Replacement mounting screw for ovens and ranges. Secures panels, brackets, trim, and internal components. Replace missing or stripped screws to restore fit.

Replacement screw secures panels, trim, and internal components in your appliance. Needed when original fastener is missing, stripped, or damaged.

Illuminates your oven interior for visibility while cooking and cleaning. Replace when burned out to restore lighting. Verify fit with your model number.

Chrome screw secures handles, door trim, and internal components in ranges and ovens. Replace if lost during cleaning, stripped, or missing after moves.

Chrome screw secures handles, door trim, and internal components in ranges and ovens. Replace if lost during cleaning, stripped, or missing after moves.

Chrome screw secures handles, door trim, and internal components in ranges and ovens. Replace if lost during cleaning, stripped, or missing after moves.