Parts for Ge ZET837BB2BB: 02 - Body Parts

A replacement left cover that restores the exterior finish and protects internal components on the appliance. Fits where the factory left side panel was damaged, cracked, dented, or removed for service. What it does

• Covers and protects wiring, controls and internal parts on the appliance's left side
• Restores the appliance's appearance after impact or wear
• Helps stop drafts, rattles, and exposure caused by a missing or damaged panel
• Maintains proper clearance and helps keep debris out of internal compartments

• One left cover

• Disconnect power (unplug or switch off breaker) before starting repair
• Remove adjacent trim or access panels as needed to reach mounting screws
• Handle edges carefully to avoid cuts; use gloves if possible
• Tighten fasteners securely but avoid overtightening which can deform the panel

The Broiler Pan Kit is an OEM part for GE ranges. It serves as a secure platform for positioning meats, vegetables, and various foods directly beneath the broiler element, ensuring safe and efficient cooking. The pan is about 17 inches wide by 13 inches deep.

Over time, wear and tear can affect broiler pans, causing issues such as flaking or stripping of the non-stick coating and the development of small ridges or holes that permit grease to drip down.

Symptoms of bad broiler pans include:

• Grease fires caused by dripping grease contacting the heating element
• A burnt or smoky flavor transferring to foods
• Difficulty removing baked-on grease and food deposits
• Pans that are misshapen or developing small cracks

This OEM GE replacement part is also compatible with select Hotpoint, RCA, and some Kenmore ranges

This is a replacement trim piece that fits around the oven bake element to restore a finished appearance and help secure the element assembly. It replaces a damaged, bent or missing trim so the element mounts cleanly and safely. What it does

• Provides a finished trim around the bake element opening to restore oven appearance
• Helps hold the bake element in its proper position and alignment
• Covers gaps or sharp metal edges left by a damaged or missing trim
• Common symptom: visible damage, missing trim, rough or sharp edges around the element area

• One replacement bake element trim

• Disconnect power to the range before any service to avoid electrical shock
• Access typically requires lowering or removing the oven door and pulling the oven cavity forward; keep track of fasteners
• Handle metal trim carefully to avoid cuts; use gloves as needed
• If the bake element is loose or damaged, inspect the element and mounting hardware and replace separately if required

This hinge assembly supports and pivots the appliance door so it opens smoothly and closes flush. Replacing a worn hinge restores alignment and reliable latching to help prevent sagging, rubbing, or an uneven door gap.

• Provides the pivot point and support for the door
• Maintains proper alignment so the door closes and latches correctly
• Helps prevent door sagging, rubbing, or uneven gaps
• Common symptoms include a loose or misaligned door, difficulty closing, or squeaking/grinding at the hinge
• Replace if the hinge is bent, cracked, or binding

• Disconnect power at the breaker before servicing; wear cut-resistant gloves
• Support the door during removal and installation to avoid strain on the hinge
• Note hinge orientation and transfer original fasteners as needed
• After installation, verify the door closes evenly and latches without rubbing

This ring-style convection heating element mounts around the fan at the back of the oven and supplies heat for convection cooking. Replacing a failed element helps bring back even air heating and consistent convection bake performance.

• Provides the heat source for convection bake/roast by warming air circulated by the fan
• Helps maintain set temperature and more even results in convection mode
• Common failure signs: no heat in convection while the fan runs, slow or incomplete preheating, uneven baking, visible breaks/blisters, or an open circuit on a continuity test
• Designed to cycle under control of the oven's sensor and electronic controls

• Disconnect power at the breaker or unplug the appliance before servicing
• Access may be from the rear of the appliance or by removing the interior panel over the convection fan, depending on the model
• Label and support the two element leads to keep them from retracting into the cavity; ensure terminals are fully seated
• Reuse existing mounting hardware; avoid bending the new element and verify it doesn't contact the oven cavity

This seal for the front frame creates a tight barrier between the oven door and frame to help retain heat and reduce smoke or odor escape. It restores a proper door seal to improve cooking performance and safety. What it does:

• Replaces worn, torn, or deformed front-frame gasket that allows heat or smoke to leak from the oven cavity
• Helps maintain consistent oven temperatures for more even cooking and baking
• Reduces heat transfer to surrounding cabinetry and surface areas
• Stops drafts, burning odors, or visible gaps around the door edge

• One seal for the front frame

• Disconnect power and let the appliance fully cool before attempting service
• Inspect orientation and seating before final installation; some models require door removal for access
• Use proper tools and gloves to avoid cuts; ensure seal is fully seated and continuous around the frame