Parts for Ge ZGP484LGR2SS: 06 - Body Parts

This lubricant/cleaner is used during service of cooking appliances to dissolve residue and provide light lubrication on small moving parts. It helps restore smoother operation of control shafts and valves when burner knobs feel stiff or sticky. What it does:

• Cleans deposits and old grease from control shafts and valve components
• Provides light lubrication to reduce friction and sticking
• Helps address symptoms such as hard-to-turn burner knobs or rough valve rotation
• Supports preventative maintenance during range/cooktop service

• Lubricant/cleaner

• Disconnect power and shut off gas; allow the appliance to cool before servicing
• Work in a well-ventilated area and keep away from open flames or ignition sources
• Apply sparingly per service instructions; avoid contact with igniters, electrical components, and flame ports
• Replace any worn or leaking valve—do not rely on lubricant/cleaner to correct a leak

This wire bushing protects appliance wiring where wires pass through metal or plastic panels, helping prevent chafing and shorts. It restores a safe insulating barrier to wiring harnesses and terminals. What it does:

• Cushions and isolates wires where they pass through openings to prevent abrasion and wire damage
• Helps stop rubbing that can wear insulation and cause arcing or shorts
• Reduces risk of intermittent power, blown fuses, or burning smells from damaged wiring
• Restores proper routing and strain relief for affected harnesses

• Remove power to the appliance before accessing wiring; disconnect power at the breaker or unplug.
• Inspect surrounding wire insulation and harness for damage; replace any wires that show charring or exposed conductors.
• Push the bushing into the opening until seated, then route the wire through the bushing to ensure a snug fit.

This LED power supply powers and regulates the refrigerator's LED lighting, restoring reliable interior illumination. It replaces a failed driver to stop flicker and prevent LEDs from remaining dark or dim. What it does:

• Converts appliance line voltage to the proper low-voltage DC for LED strips
• Keeps LED lights stable and prevents flickering or intermittent operation
• Restores full brightness when a failed driver causes dim or no interior lighting
• Protects LEDs from irregular voltage that can shorten lamp life

• Disconnect power to the appliance before starting any work to avoid shock.
• Handle the board and connectors carefully to avoid static or physical damage.
• Basic hand tools and access to the light housing/panel are usually required.

This bake supply tube assembly routes gas to the oven's bake burner so the oven can produce heat for baking. It replaces a damaged or leaking tube to restore proper burner operation and safe performance. What it does:

• Delivers gas from the manifold to the oven's bake burner for ignition and steady flame
• Restores normal baking heat when the supply tube is cracked, clogged, or disconnected
• Helps eliminate weak or no-bake heat caused by interrupted gas flow
• Designed to align with the oven's burner and sealing surfaces for proper combustion

• For gas appliances: turn off gas supply and electricity before servicing; follow manufacturer instructions
• Install only when cool; inspect and replace any damaged gaskets or fittings
• Use proper fittings and tighten to OEM torque; check all connections for leaks after installation with an approved method

This relay board assembly routes power to the appliance's compressor and fans so cooling cycles and motor functions run correctly. Replacing a failed relay board restores proper power switching without replacing major components. What it does

• Switches power to compressor and condenser/evaporator fans through relay contacts
• Enables start/run sequences for motors and compressors
• Common symptom: appliance not cooling or cooling inconsistently
• Common symptom: loud clicking, repeated start attempts, or compressor/fans not running
• Works as the electrical switching module tied to the main control/relay system

• Disconnect power before servicing to avoid shock or damage
• Handle the board by edges and avoid ESD-sensitive contact with components
• Verify connector fit and orientation before powering up

This replacement line cord provides the appliance's main power connection, restoring a safe, reliable electrical feed when the original cord is damaged or worn. Use it to replace frayed, cut, or non-functioning power leads. What it does:

• Carries household mains power to the appliance for normal operation
• Replaces damaged or frayed cords that can cause intermittent power or visible wear
• Helps eliminate loose connections, burning smell, or sparking at the cord entry
• Restores a secure grounded connection when used with the correct grounding configuration

• Disconnect power at the breaker or unplug the appliance before starting
• Verify cord type and grounding configuration match the appliance wiring and local code
• Inspect terminal connections for corrosion and tighten to manufacturer torque specs

This genuine replacement screw secures panels, trim and small components on compatible appliances to restore proper fit and prevent rattling or gaps. Use it when a missing or damaged fastener causes loose or misaligned parts. What it does:

• Fastens panels, bezels, trim pieces and small assemblies to the appliance frame
• Restores secure fit to eliminate rattling, vibration noise or loose trim
• Replaces stripped, rusted or missing screws that prevent proper alignment

• Disconnect power to the appliance before servicing to avoid electrical hazard
• Use the correct screwdriver or driver bit to prevent stripping the head
• Tighten securely but avoid over-torquing; excessive force can strip threads or crack plastics
• Keep removed fasteners organized to ensure correct reassembly

This anti-tip bracket secures a freestanding range or oven to the floor or wall to help prevent tipping during normal use, improving safety and stability. Simple, durable bracket designed to restore the factory anchoring point. What it does:

• Anchors the rear/base of a freestanding range to help prevent the unit from tipping forward
• Reduces rocking or shifting when opening heavy oven doors or sliding cookware
• Restores the proper mounting point after damage or missing hardware
• Helps address symptoms like a range that tilts or moves when pressure is applied

• One anti-tip bracket

• Follow the appliance OEM installation instructions; bracket mounts to floor or wall framing—locate a stud or secure to recommended substrate
• Turn off and disconnect power (and gas if applicable) and remove access panels as required before beginning work
• Use proper fasteners for your floor/wall material; do not rely on adhesive or weak anchors

This anti-tip brace secures the range to the floor or wall to help prevent the appliance from tipping forward when a heavy load is on an open oven door or when pressure is applied to the top edge. It restores a key safety restraint and helps stabilize the appliance. What it does

• Anchors the range to reduce forward tipping when the oven door is open or heavy items are placed on the door
• Helps prevent accidents and appliance movement during normal use
• Works with the range's built-in leveling and mounting points to provide a secure attachment
• Commonly replaced after a move, installation, or if the original bracket is damaged or missing

• One anti-tip brace

• Follow the appliance installation manual for correct placement and mounting location
• Unplug the appliance (or shut off power) and remove access panels as needed before installing
• Use appropriate fasteners for your floor/wall material; secure to framing or floor as specified

A 45 mm tangential blower that restores directed airflow in heating and cooling cavities to help maintain even temperatures and protect internal components. Fits factory blower mounts and connects to existing wiring harnesses. What it does:

• Moves air along the oven/cabinet cavity to promote even heat distribution and help vent hot spots
• Cools nearby electronics and components to reduce overheating risk
• Replaces worn or noisy blowers to restore proper airflow and reduce unusual motor noise
• Helps maintain designed airflow for venting and exhaust paths

• Disconnect power at the breaker before starting any repair
• Handle with care; blower edges and surrounding sheet metal may be sharp
• Verify blower orientation and wiring match the original before securing
• Basic hand tools typically needed; follow for panel removal and reassembly

This side support panel replaces a damaged or missing support on the appliance's side, helping secure and align the cabinet and trim so the unit sits solidly and looks finished after installation or service. What it does:

• Provides structural support for the side of the appliance cabinet and adjacent trim
• Helps maintain correct spacing and alignment next to countertops or panels
• Replaces a bent, warped, or corroded panel
• Reduces rattles or rubbing caused by a loose side assembly

• One side support panel

• Disconnect power; turn off gas supply before servicing
• Carefully pull the unit forward for side access; support it to prevent tipping
• Remove fasteners, transfer any clips/brackets from the old panel, and reinstall with existing hardware
• Wear cut-resistant gloves and verify clearances and level before final tightening

This small metal nipple secures or connects appliance components, restoring proper alignment and a stable mechanical or fluid connection. It's a simple replacement that helps appliances function reliably. What it does:

• Provides a secure mounting point or connection between parts
• Restores proper alignment for linked components
• Replaces worn or damaged fittings that can cause rattling or instability
• Helps maintain a leak-free or stable mechanical joint when used as intended

• Disconnect power and/or gas and follow all safety procedures before starting work
• Install in the original orientation; hand-start fasteners to avoid cross-threading, then tighten to secure
• If the nipple interfaces with a fluid or gas line, inspect seals and replace gaskets or O-rings as needed and check for leaks after reassembly

This threaded connector secures or joins short sections of tubing or hose on select appliances, restoring a tight, reliable connection. Use when the original nipple is corroded, stripped, or leaking. What it does:

• Provides a secure, threaded connection between tubing, hose, or fittings
• Maintains a sealed joint to help prevent leaks at the connection point
• Replaces damaged or worn nipples that can cause loose fittings or loss of flow
• Commonly used where a short, durable threaded coupling is required

• One nipple

• Disconnect power and shut off water or gas supply before servicing
• Inspect mating threads and replace any damaged seals or washers
• Hand-start threads to avoid cross-threading, then tighten with the appropriate wrench
• After installation, restore supply and check carefully for leaks during a test run

This oven gas pressure regulator controls and stabilizes gas flow to the oven burner so the appliance heats reliably and maintains consistent cooking temperatures. Replaces a worn or failed regulator to restore normal burner operation. What it does:

• Regulates gas pressure delivered to the oven burner for steady flame and temperature control.
• Helps prevent low or uneven heat that can cause undercooked food or extended cook times.
• Works as part of the oven's gas supply system and interacts with the thermostat and safety valves.

• Turn off gas supply and electrical power before servicing; test for leaks after installation.
• Replacement may require basic appliance service skills and the correct fittings.
• Do not modify the part; use only as specified by the manufacturer.

This handle spacer positions the appliance handle at the correct distance from the door or panel for smooth operation. Replacing a worn or missing spacer restores proper standoff, alignment, and feel, and helps prevent rubbing, rattling, or looseness.

• Maintains proper spacing between the handle base and mounting surface
• Helps keep the handle aligned and secure
• Reduces rubbing or contact with the door/panel
• Common fix for a wobbly, misaligned, or scraping handle

• Unplug power and allow hot surfaces to cool before servicing
• Support the door/handle while removing mounting screws to prevent strain
• Note the spacer's position and orientation; reinstall the new spacer in the same location
• Tighten screws snugly; do not overtighten to avoid damage

The Wall Oven Capacitor Motor is an OEM part for GE wall ovens. Located inside the oven cavity, this motor is responsible for turning the convection fan which circulates hot air for even baking and roasting. 

Symptoms of a bad capacitor motor include:

• Inability to select convection bake or roast features 
• Uneven cooking results 
• Lack of air circulation inside the oven
• Strange noises coming from the fan/motor area
• The convection fan not turning on 

Causes of failure can be wear over time, damage from debris inside the oven, or occasional voltage fluctuations which can degrade motor components.

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

This tee connector joins and directs the refrigerator water supply to multiple lines, restoring proper water flow for the ice maker and dispenser. It's a simple replacement that helps stop leaks and re-establish reliable water delivery. What it does:

• Connects a main water line to two branch lines so water reaches the ice maker and dispenser
• Replaces a damaged or leaking tee to stop visible drips or pooling near the inlet
• Restores normal water flow when a cracked or blocked connector restricts supply
• Works with the refrigerator's inlet plumbing to maintain proper service of ice/water features

• One tee connector

• Shut off the refrigerator's water supply before replacing this part
• Disconnect power or unplug the appliance if replacing near electrical components
• Use appropriate tubing fittings and check for tight, leak-free connections after installation

The Screw is an OEM replacement part for GE refrigerators. Countless screws are used throughout the refrigerator to securely hold parts in place.

Symptoms of a bad or missing screw can include:

• Rattling or vibration noises coming from inside the appliance 
• Doors or other parts that are no longer properly aligned
• Increased frost or cold air leaks due to compromised seals

Causes may include normal wear and tear over time, accidental damage or loss of a screw during repairs, or improper assembly leaving crucial screws omitted. 

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore refrigerators.

The Reed Switch Pcb is an OEM part for GE gas ranges. This component plays a crucial role in the burner control system by detecting the on/off position of the control knobs. 

Causes of a bad reed switch pcb include circuitry failure, component degradation over time, damage from falls or impacts, or issues with the wiring connections. 

Symptoms of a bad reed switch pcb include:

• Burners not igniting when turned on  
• Ignition sparks but burners fail to light
• Unresponsive or intermittent control knob functionality
• Inability to turn burners off

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.