Parts for Ge ZGP486LDR2SS: 06 - Body Parts

This kit includes the orifices and carrier assembly needed to convert a range from liquid propane (LP) to natural gas operation. It ensures the burners receive the correct gas flow rate for safe and efficient combustion on natural gas. Use this kit when switching your fuel source, or replace it if you notice uneven flames, yellow burner tips, or improper ignition after a gas line change.

Stainless steel cleaner for gas ranges and cooktops. Restores shine and removes fingerprints, smudges, and streaks from exterior surfaces.

Lubricant cleaner for range and oven control shafts, burner valves, and rack paddles. Dissolves residue and restores smooth operation when parts feel stiff.

This bake supply tube assembly routes gas to the oven's bake burner so the oven can produce heat for baking. It replaces a damaged or leaking tube to restore proper burner operation and safe performance. What it does:

• Delivers gas from the manifold to the oven's bake burner for ignition and steady flame
• Restores normal baking heat when the supply tube is cracked, clogged, or disconnected
• Helps eliminate weak or no-bake heat caused by interrupted gas flow
• Designed to align with the oven's burner and sealing surfaces for proper combustion

• For gas appliances: turn off gas supply and electricity before servicing; follow manufacturer instructions
• Install only when cool; inspect and replace any damaged gaskets or fittings
• Use proper fittings and tighten to OEM torque; check all connections for leaks after installation with an approved method

This wire bushing protects appliance wiring where wires pass through metal or plastic panels, helping prevent chafing and shorts. It restores a safe insulating barrier to wiring harnesses and terminals. What it does:

• Cushions and isolates wires where they pass through openings to prevent abrasion and wire damage
• Helps stop rubbing that can wear insulation and cause arcing or shorts
• Reduces risk of intermittent power, blown fuses, or burning smells from damaged wiring
• Restores proper routing and strain relief for affected harnesses

• Remove power to the appliance before accessing wiring; disconnect power at the breaker or unplug.
• Inspect surrounding wire insulation and harness for damage; replace any wires that show charring or exposed conductors.
• Push the bushing into the opening until seated, then route the wire through the bushing to ensure a snug fit.

Range display lights flickering or completely dark? This LED power supply module converts voltage to power your control panel lighting. Moderate DIY repair.

This relay board assembly routes power to the appliance's compressor and fans so cooling cycles and motor functions run correctly. Replacing a failed relay board restores proper power switching without replacing major components. What it does

• Switches power to compressor and condenser/evaporator fans through relay contacts
• Enables start/run sequences for motors and compressors
• Common symptom: appliance not cooling or cooling inconsistently
• Common symptom: loud clicking, repeated start attempts, or compressor/fans not running
• Works as the electrical switching module tied to the main control/relay system

• Disconnect power before servicing to avoid shock or damage
• Handle the board by edges and avoid ESD-sensitive contact with components
• Verify connector fit and orientation before powering up

Replacement power cord for gas ranges. Installs at the rear connection to supply mains electricity. Order when your original cord is frayed, cut, damaged, or worn.

Size: 8-18 x 1/2 inch.

Panel mounting screw secures trim, bezels, and internal components on ranges and cooktops. Replace when stripped, corroded, or missing to restore fit.

Front frame gasket for gas ranges. Replace when worn, cracked, or causing heat loss around oven door. Verify compatibility with your model number.

Replace your gas range door frame gasket to restore proper sealing and heat retention. Prevents heat loss and improves oven efficiency. Verify fit with your model.

Secures the toe kick panel to your range base. Replace if the toe kick is loose, rattling, or won't stay in place. Verify fit with your model number.

Leveling leg kit for ranges and wall ovens. Includes adjustable feet to stabilize and level your appliance. Replace cracked, bent, or missing legs.

Secures freestanding ranges to the floor or wall to prevent tipping. Replace if bracket is missing, bent, or damaged during appliance installation.

Secures your range to the floor or wall to prevent tipping when the oven door is open. Replace if bracket is bent, broken, or missing during installation.

Fix uneven oven heating or poor air circulation with this tangential blower fan. Essential for proper convection airflow in gas ranges. DIY install.

Fix uneven oven temperatures or overheating electronics with this 45mm tangential blower motor. Restores directed airflow in your gas range cavity.

This side support panel replaces a damaged or missing support on the appliance's side, helping secure and align the cabinet and trim so the unit sits solidly and looks finished after installation or service. What it does:

• Provides structural support for the side of the appliance cabinet and adjacent trim
• Helps maintain correct spacing and alignment next to countertops or panels
• Replaces a bent, warped, or corroded panel
• Reduces rattles or rubbing caused by a loose side assembly

• One side support panel

• Disconnect power; turn off gas supply before servicing
• Carefully pull the unit forward for side access; support it to prevent tipping
• Remove fasteners, transfer any clips/brackets from the old panel, and reinstall with existing hardware
• Wear cut-resistant gloves and verify clearances and level before final tightening

This small metal nipple secures or connects appliance components, restoring proper alignment and a stable mechanical or fluid connection. It's a simple replacement that helps appliances function reliably. What it does:

• Provides a secure mounting point or connection between parts
• Restores proper alignment for linked components
• Replaces worn or damaged fittings that can cause rattling or instability
• Helps maintain a leak-free or stable mechanical joint when used as intended

• Disconnect power and/or gas and follow all safety procedures before starting work
• Install in the original orientation; hand-start fasteners to avoid cross-threading, then tighten to secure
• If the nipple interfaces with a fluid or gas line, inspect seals and replace gaskets or O-rings as needed and check for leaks after reassembly

This threaded connector secures or joins short sections of tubing or hose on select appliances, restoring a tight, reliable connection. Use when the original nipple is corroded, stripped, or leaking. What it does:

• Provides a secure, threaded connection between tubing, hose, or fittings
• Maintains a sealed joint to help prevent leaks at the connection point
• Replaces damaged or worn nipples that can cause loose fittings or loss of flow
• Commonly used where a short, durable threaded coupling is required

• One nipple

• Disconnect power and shut off water or gas supply before servicing
• Inspect mating threads and replace any damaged seals or washers
• Hand-start threads to avoid cross-threading, then tighten with the appropriate wrench
• After installation, restore supply and check carefully for leaks during a test run

Controls gas flow to your range oven burner. Replace this regulator if it's cracked, corroded, or leaking to restore proper gas pressure control.

Positions your range handle at the correct distance from the door. Replace if worn, missing, or cracked to restore proper alignment and prevent rattling.

Fix a gas range that won't heat with this safety valve assembly. Controls gas flow to oven and burners, restoring safe operation when the valve opens.

The Wall Oven Capacitor Motor is an OEM part for GE wall ovens. Located inside the oven cavity, this motor is responsible for turning the convection fan which circulates hot air for even baking and roasting. 

Symptoms of a bad capacitor motor include:

• Inability to select convection bake or roast features 
• Uneven cooking results 
• Lack of air circulation inside the oven
• Strange noises coming from the fan/motor area
• The convection fan not turning on 

Causes of failure can be wear over time, damage from debris inside the oven, or occasional voltage fluctuations which can degrade motor components.

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

Mounting bracket that secures the capacitor to your range frame. Replace if bent, broken, or missing to properly support and position the capacitor.

This tee connector joins and directs the refrigerator water supply to multiple lines, restoring proper water flow for the ice maker and dispenser. It's a simple replacement that helps stop leaks and re-establish reliable water delivery. What it does:

• Connects a main water line to two branch lines so water reaches the ice maker and dispenser
• Replaces a damaged or leaking tee to stop visible drips or pooling near the inlet
• Restores normal water flow when a cracked or blocked connector restricts supply
• Works with the refrigerator's inlet plumbing to maintain proper service of ice/water features

• One tee connector

• Shut off the refrigerator's water supply before replacing this part
• Disconnect power or unplug the appliance if replacing near electrical components
• Use appropriate tubing fittings and check for tight, leak-free connections after installation

Replacement screw for refrigerators. Secures handles, panels, and internal components. Order if yours is missing, stripped, or lost during repairs.

Fix burners that won't ignite or turn off when your gas range control knobs aren't responding. This reed switch board detects knob positions.