Parts for Hot Point RGA720EK2WH: 03 - Body Parts

This line cord supplies electrical power from the wall outlet to the appliance. Replacing a worn, cut, or heat-damaged cord restores safe, reliable power and can help resolve no-power or intermittent operation issues.

• Delivers AC power from the outlet to the unit's electrical system
• Helps correct no-power or intermittent power when the cord is moved
• Ideal replacement for cords with cuts, fraying, or burn/discoloration on the plug
• Supports proper grounding and safe operation when installed correctly

• Disconnect power before servicing; ensure the appliance is fully de-energized
• Match wire routing and connections to the product's wiring diagram; ensure a secure ground
• Use an appropriate strain relief if required by the product to prevent abrasion
• Route the cord away from sharp edges, moving parts, and hot surfaces

This genuine replacement screw secures panels, trim and small components on compatible appliances to restore proper fit and prevent rattling or gaps. Use it when a missing or damaged fastener causes loose or misaligned parts. What it does:

• Fastens panels, bezels, trim pieces and small assemblies to the appliance frame
• Restores secure fit to eliminate rattling, vibration noise or loose trim
• Replaces stripped, rusted or missing screws that prevent proper alignment

• Disconnect power to the appliance before servicing to avoid electrical hazard
• Use the correct screwdriver or driver bit to prevent stripping the head
• Tighten securely but avoid over-torquing; excessive force can strip threads or crack plastics
• Keep removed fasteners organized to ensure correct reassembly

This replacement screw secures appliance components so panels, brackets, and trim stay tight and aligned. Use it to replace a missing, stripped, or rusted fastener and restore a solid, rattle-free fit in the affected assembly.

• Fastens parts to the chassis/frame or mounting brackets
• Replaces lost, damaged, or corroded hardware
• Can help address loose or vibrating panels and minor misalignment
• Maintains a secure attachment during normal operation

• Disconnect power before servicing; for gas appliances, also shut off the gas supply
• Match the screw to the original location and reuse any clips or washers if present
• Start threading by hand to avoid cross-threading; tighten snugly without overtightening
• Repair/replace damaged receiving threads or clip for proper hold

This mounting screw secures appliance components to the chassis for a tight, rattle-free fit. Replacing a missing, stripped, or corroded fastener helps keep panels, brackets, or burner assemblies properly aligned and secure.

• Fastens designated parts to the appliance frame or mounting points
• Helps maintain proper alignment of panels, trim, brackets, or burner assemblies
• Restores hold when the original screw is worn, rusted, or lost
• Symptoms include loose or wobbly components, rattling/vibration, or visible gaps

• Disconnect power; allow all surfaces to cool. For gas units, also shut off the gas supply.
• Use the correct driver/bit; avoid cross-threading.
• If mating threads or clip/nut are damaged, repair or replace them before installing.
• Tighten until secure; do not overtighten to prevent stripping.

This cable clamp secures the appliance power cord where it enters the cabinet, protecting wiring from pull and chafe for safer, more reliable operation. Designed to hold the cord firmly in place and prevent accidental disconnection. What it does:

• Acts as a strain relief to prevent the power cord from pulling into or away from the appliance
• Protects wiring from abrasion and sharp edges at the entry point
• Helps maintain a secure electrical connection to reduce intermittent power issues
• Commonly used where the cord passes through a rear or bottom access panel

• Disconnect power before inspecting or replacing the clamp to avoid shock or injury
• Install at the cord entry so the clamp captures the cord jacket; tighten fastener securely but do not over-torque
• Verify the cord is correctly routed and not pinched when reassembling panels
• If any wiring or the cord jacket is damaged, replace the cord before restoring power

This oven floor deflector assembly restores proper airflow and heat protection in the lower oven cavity so food cooks evenly and internal components stay shielded from direct heat. It's a direct replacement for a damaged or warped deflector. What it does:

• Redirects and evens oven heat across the lower cavity to improve baking and roasting consistency.
• Shields internal insulation and components from hot bake/broil flames and debris.
• Replaces warped, dented, or missing deflector that can cause uneven cooking or rattling.
• Helps prevent direct flame contact with oven floor and lowers risk of food drippings burning on surfaces.

• One bottom oven and deflector assembly

• Disconnect power to the appliance and allow the oven to cool completely before starting.
• Basic hand tools are typically required; follow the appliance service manual for panel removal steps.
• Handle edges carefully—metal parts may be sharp.

Size: 8-18 x 1/2 inch.

Includes 12 speed nuts.

This capillary clip secures the oven thermostat's sensing bulb/capillary to the cavity wall so it stays correctly positioned for accurate temperature control. Replace a missing or damaged clip to prevent a sagging bulb and erratic oven performance.

• Holds the thermostat capillary tube/sensing bulb in place inside the oven
• Helps maintain consistent temperature regulation by keeping the bulb properly located
• Direct replacement for a broken, corroded, or missing clip
• Symptoms include a loose or dangling bulb, uneven baking, or temperature swings

• Disconnect power (and gas, if applicable) and allow the oven to cool completely
• Access the oven cavity; locate the thermostat sensing bulb and capillary along the wall or back panel
• Position the bulb/capillary and secure with the new clip; avoid kinking or crushing the tube
• Restore power, and test operation

Anti-tip kit.

This replacement leveling screw secures and adjusts an appliance's leg so the unit sits level and stable on the floor. Restores proper tilt for even door operation and stable performance. What it does:

• Replaces a worn or damaged leveling screw used to raise or lower an appliance leg
• Helps stop rocking, reduce vibration, and keep doors aligned
• Common fix when an appliance tilts forward/back or is uneven on the floor
• Works with the corresponding leveling leg/assembly to set final height

• Support the appliance before adjusting or removing leveling hardware to prevent tipping
• Use appropriate hand tools; tighten securely but avoid over-torquing
• No electrical disconnection is typically required, but unplug if working near electrical components
• If the leveling leg assembly is damaged, replace the entire leg/assembly per manufacturer instructions

This hinge deflector guides and protects the refrigerator door at the top hinge, helping the door open and close smoothly and preventing rubbing or catching. It restores correct door alignment and reduces wear on hinge components. What it does:

• Guides the door on the top hinge to maintain proper movement and alignment
• Helps prevent the door from rubbing, scraping, or catching on the cabinet
• Reduces wear and noise at the hinge area caused by misalignment
• Supports smooth opening and closing for a secure seal

• One hinge deflector

• Always unplug the appliance or switch off power before starting work
• Support the door before removing or loosening the top hinge to prevent injury or damage
• Remove the top hinge hardware, replace the deflector, then reassemble and tighten hardware securely
• Check door alignment and operation after installation; adjust hinge hardware as needed