Parts for Tappan TPF303BWE: 07 - Body Parts

This factory screw secures panels, brackets, and other components in your cooking appliance. Replace a missing, stripped, or corroded fastener to restore a tight, rattle-free fit and keep parts properly aligned during use.

• Fastens components to maintain proper alignment and stability
• Helps prevent vibration, rattling, and loose parts during operation
• Replace if threads are stripped, the head is damaged, or the screw is missing
• Commonly used to mount internal or exterior parts in ranges and wall ovens

• Disconnect power and allow the appliance to cool; shut off gas supply if applicable
• Use the correct driver bit to avoid stripping the screw head
• Install in the original location and do not overtighten
• If the receiving threads are damaged, repair or replace the mating part before installation

The Leveling Leg Assembly is an OEM part for Frigidaire ranges. This part provides stability by allowing users to adjust the height of the range, ensuring it is level and balanced on the floor.  

Causes of a bad leveling leg assembly can include wear from frequent adjustments, damage due to heavy loads, or breakage from accidental impacts.  

Symptoms of a bad leveling leg assembly include:

• The range being uneven or wobbling
• Difficulty in leveling the range using the legs
• Noise or movement when the range is in use
• Doors not aligning properly

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The Oven Rack is an OEM part for Frigidaire ovens, designed to provide a stable and durable surface for baking and roasting inside the appliance. This rack is essential for facilitating proper air circulation around food, ensuring even cooking and optimal baking results. The rack measures about 23 inches wide by 16 inches deep.

The primary reasons for replacing an Oven Rack usually involve normal wear and tear from regular use, including the effects of high heat, spills, and the burden of heavy pots and pans.  

Symptoms of a needing replacement Oven Rack include:

• Warping or bending from heat exposure or the weight of heavy cookware, which can affect cooking results
• Rust or corrosion that might not only compromise the integrity of the rack but also pose a risk of contaminating food
• Difficulty in sliding the rack in and out smoothly, which could indicate a misshapen rack or damage to its guides

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

Replacement refrigerator door hinge that supports proper door alignment and smooth opening and closing. Restores secure door operation to prevent sagging, binding or air leaks when a hinge is worn or damaged.

• Supports and pivots the refrigerator door for stable, reliable opening and closing.
• Maintains door alignment to reduce gaps that can cause cold air loss and temperature issues.
• Designed to match factory fit and function for the door hinge mechanism.

• Disconnect power and remove food from the door before starting to reduce risk of injury or damage.
• Support the door while removing and installing the hinge to prevent it from falling or bending.
• Retain original mounting hardware; use the correct screws and torque values per the service manual.

This replacement clip secures components within your appliance. Replacing a broken, bent, or missing clip restores a firm hold on panels or assemblies to prevent shifting and reduce vibration noise.

• Holds specified parts or panels in place where a clip is called out in the assembly
• Helps maintain proper alignment and minimizes rattles/vibration
• Direct replacement for a damaged or missing clip
• Common symptoms: loose or misaligned parts, rattling during operation, clip visibly broken or missing

• Disconnect power before service; also shut off gas/water supplies
• Note the original clip orientation and placement; take a photo for reference
• Use needle-nose pliers for removal/installation; avoid overbending or deforming the clip
• Inspect mating parts for wear or damage and ensure the clip seats fully

This channel burner support is a stamped support bracket designed to hold and align the range burner channel and related components so burners sit correctly. It helps restore proper fit and stable burner operation. What it does:

• Secures the burner channel and keeps burners aligned for consistent heating
• Prevents wobbling or misalignment of the burner assembly during use
• Helps maintain correct spacing between burner components and gas valve/manifold
• Commonly replaced when the original support is bent, cracked, or damaged

• One channel burner support bracket

• Designed to mount with existing fasteners; inspect screws or clips and replace if worn
• Turn off power and gas supply (for gas ranges) before servicing; follow appliance safety procedures
• Handle sharp edges carefully; wear gloves to avoid cuts

This flue directs exhaust and heat away from the oven cavity to the range vent path, helping maintain proper ventilation and combustion airflow. It replaces damaged or corroded flue components to restore safe venting and oven performance. What it does:

• Channels heat, smoke and combustion exhaust from the oven cavity toward the vent path
• Helps prevent heat buildup behind the oven control area and adjacent panels
• Can reduce visible soot, odors or poor venting caused by a cracked or bent flue
• Supports proper burner combustion airflow in gas models when correctly installed

• One replacement flue

• Disconnect the appliance from power (and gas supply on gas models) before starting work
• Access typically requires removing the oven back panel or drop-in cooktop; keep track of mounting screws and gaskets
• Wear gloves to protect from sharp sheet-metal edges and use caution aligning the flue to vent openings
• After installation, restore power/gas and verify normal oven operation and proper venting; check for signs of leaks or loose fasteners

This is the right side cover. For left side use 316233500.

This is the left side cover. For right side use 316233400.

Note: ONE screw only, order as needed.

This oven back insulation panel fits behind the oven cavity to help contain heat and protect rear components. It replaces missing or damaged insulation to help restore normal oven heating behavior and reduce heat transfer to surrounding areas. What it does:

• Limits heat loss from the rear of the oven cavity to help maintain cooking temperature
• Helps reduce excessive heat transfer to rear components and cabinetry
• Use when insulation is torn, compressed, burned, or when the oven takes noticeably longer to preheat
• Helps prevent heat-related damage to wiring, electronics, and nearby parts

• Disconnect power to the appliance before starting any repair
• Access may require pulling the range/oven away from the wall and removing a rear access panel
• Wear gloves and a dust mask when handling old insulation; avoid compressing or tearing the replacement
• Follow OEM instructions for securing insulation with the original clips/adhesive or fasteners

The Anti-Tip Bracket Kit is an OEM part for Frigidaire ranges and ovens. This part secures the appliance to the floor or wall, preventing it from tipping over when the oven door is opened or when heavy cookware is placed on an open door or extended rack. The kit typically includes a metal bracket, screws, and installation instructions.

Over time, or during instances of moving or remodeling, the anti-tip bracket may become dislodged or may not be reinstalled correctly, which can compromise the safety of the appliance. 

Symptoms of a missing or improperly installed Anti-Tip Bracket include:

• The range or oven tilts forward when pressure is applied to an open door
• The appliance moves more easily than expected when nudged or cleaned
• Visible absence of a bracket at the lower back portion or floor area behind the appliance

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

Size: 8-18ab x 0.5 inch.

Color: Black

Size: 8-32t x 0.500 inch. Color: Black.

The Frigidaire Touch-Up Paint is white in color in a .6 fl oz bottle. For almond order 5303321320. For black order 5303321321.

The Touch Up Paint is an OEM part for Frigidaire appliances. Whether you're dealing with scratches, chips, or other minor cosmetic damage, this touch-up paint provides an easy and effective solution for maintaining the appearance of your appliance. It's designed to adhere well to metal surfaces, offering durability and resistance to further wear and tear.

Over time, appliances can accumulate minor surface damage from regular use, cleaning, and accidental impacts. Using the Touch Up Paint not only improves the aesthetic appeal of your appliance but also helps protect exposed areas from rust and corrosion, which can extend the life of the appliance.

Symptoms of needing Touch Up Paint include:

• Visible scratches or chips on the appliance's surface.
• Areas of rust or corrosion that need to be covered after treating the rust.
• The desire to maintain or improve the appliance's appearance for aesthetic reasons or to maintain its value.