Parts for Ge JB755FJ8DS: Body Parts

Mounting bracket that secures the capacitor to your range frame. Replace if bent, broken, or missing to properly support and position the capacitor.

Rangetop enclosure for electric ranges. Installs on the main cooking surface to contain and support the heating elements. Replace if cracked or damaged.

Replace your electric range's lower drawer assembly if bent, jammed, cracked, or missing. Restores smooth glide operation and proper alignment.

Replace a cracked, dented, or missing side panel on your electric range. This structural cover panel installs on the exterior side of your appliance.

Rear insulation panel that installs behind the oven cavity to contain heat and protect surrounding components. Replace if cracked, damaged, or missing.

Replace a missing, bent, or corroded oven rack in your electric range. This rack slides on side rails to support bakeware and cookware at the correct level.

Aligns and stabilizes your range's lower storage or warming drawer for smooth sliding and flush closure. Replace if cracked, worn, or missing to restore fit.

Oven slow to heat or not heating at all? This hidden bake element delivers consistent bottom heat for proper baking. Moderate DIY, about 1 hour.

Broiler not working or burned out? This broil element radiates intense heat from above to sear and brown foods. Straightforward DIY replacement.

Fix F2 error codes and inaccurate oven temperatures by replacing a faulty temperature sensor. Simple 15-minute DIY repair with basic tools.

Halogen oven light assembly illuminates your electric range interior so you can monitor cooking without opening the door. Replace when dim or burned out.

Black front trim frame for electric range. Covers gaps and restores finished edge around door or control panel. Replaces cracked, scratched, or missing trim.

Secures your range to the floor or wall to prevent forward tipping. Replace if bracket is bent, broken, or missing during appliance relocation.

Range won't power on or has a loose power connection? This terminal block mount secures the electrical connection. Straightforward install in under an hour.

Secures your range door hinge to the cabinet frame for proper pivot and seal. Replace if door sags, won't close flush, or hinge is loose. Confirm fit with your model number.

The Rear Door Support is an OEM replacement part for GE ranges. Located at the base of the range, this bracket provides weight-bearing support for the lower oven drawer. It facilitates smooth extension and retraction of the drawer.

Causes of faulty support can include cracks or fractures developing over extended use, worn joints unable to sustain drawer weight, or misalignment from repeated opening/closing stress.

Symptoms of a bad support include:

• Loose or sagging lower oven drawer
• Grinding or binding noises when operating the drawer
• Difficulty fully extending or retracting the drawer
• The drawer not sitting securely in a closed position

This OEM GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore ranges.

Reflector pan sits under the bake element in your electric range oven cavity. Replace if cracked, warped, or rusted to restore proper heat direction.

The Wall Oven Capacitor Motor is an OEM part for GE wall ovens. Located inside the oven cavity, this motor is responsible for turning the convection fan which circulates hot air for even baking and roasting. 

Symptoms of a bad capacitor motor include:

• Inability to select convection bake or roast features 
• Uneven cooking results 
• Lack of air circulation inside the oven
• Strange noises coming from the fan/motor area
• The convection fan not turning on 

Causes of failure can be wear over time, damage from debris inside the oven, or occasional voltage fluctuations which can degrade motor components.

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

This temperature sensor harness connects the refrigerator/freezer thermistor to the main control board, restoring reliable temperature sensing and control. It helps the appliance maintain consistent cooling by ensuring the temperature sensor communicates correctly. What it does:

• Carries the thermistor signal from the evaporator/well sensor to the control board
• Replaces frayed, damaged, or corroded wiring that can cause temperature errors
• Helps resolve symptoms like erratic temperatures, incorrect cooling cycles, or temperature error codes
• Maintains proper connector fit and routing to prevent intermittent sensor readings

• One temperature sensor harness

• Disconnect power before installing to avoid shock or short circuits
• Access may require removing interior panels or the control housing; keep fasteners organized
• Match connector orientation and route harness away from sharp edges and moving components

Hex washer head screw secures panels, brackets, and small assemblies inside refrigerators and ranges. Replace stripped, missing, or damaged screws.

Secures components to your appliance chassis for a rattle-free fit. Replace missing, stripped, or corroded screws to keep panels and brackets aligned.

Replacement mounting screw for cooktops and ranges. Secures cooktop components to the frame. Replace if screw is stripped, missing, or damaged.