Bolens Trimmer

A recoil pull-start assembly is the engine's starting mechanism. The machine operator pulls on the rope, which activates the pulley system to start the machine's engine. This part is a recoil pull-start assembly kit contains a rope, a pulley, and an innerspring, which are all of the components of the pull start assembly. A pull-start assembly kit may be needed if the recoil or pulley system has broken due to use over time. The rope may become broken or frayed and the plastic on the pulley could crack. While the rope itself is available separately, it's a good idea just to replace the entire pull start assembly kit while in the process of replacing any of the components to ensure even wear. This genuine OEM MTD part is sourced directly from the manufacturer. It is sold individually. It is used on blowers, vacuums, and trimmers that are manufactured by Craftsman, Bolens, MTD, and Troy-Bilt.

This muffler assembly is a genuine MTD part, sold individually. A muffler assembly can be used as a replacement part in a string trimmer or a leaf blower. The purpose of this genuine OEM part for one of these outdoor appliances is to reduce noise made by the motor while the blower in use.The muffler assembly in a string trimmer or a leaf blower can become damaged throughout its typical lifespan, and if this damage necessitates a complete replacement of the part, the muffler assembly should be removed and replaced with this genuine OEM replacement part as soon as possible. This component is a genuine OEM replacement part sourced directly from the manufacturer. It is sold individually. This muffler assembly is compatible with the following outdoor appliance brands: MTD, Craftsman, Cub Cadet, Ryobi, Troy-Bilt, Yard Machines, Bolens, and Yard Man.

This drive shaft is a genuine MTD part. It is normal for the drive shaft to wear out over time and need to be replaced. It may completely break, but you should check it from time to time to make sure it is in good working order; otherwise, it may snap in the middle of using the trimmer, which can be a major inconvenience. In order to perform this repair safely, first, remove the wire and boot from the spark plug. Otherwise, the engine may accidentally start, creating a potentially dangerous situation. Mind the line cutter while working. This is not a difficult repair, but the air filter, throttle cable, ignition wires, and shaft housing may all need to be removed.This drive shaft is a genuine OEM part sourced directly from the manufacturer and is sold individually. It is compatible with several models of yard trimmers or edgers. These include models manufactured by Bolens, McCulloch, Yard Machines, and Yard-Man.

This part is a replacement recoil starter assembly. This is a genuine OEM part made by MTD and has been sourced directly from the manufacturer. This part's intended use is to replace a broken or defective recoil starter assembly in line trimmers.The recoil starter assembly is what spins the line trimmer flywheel in order to start up the engine. This part is critical and the line trimmer may not function if it is broken or malfunctioning. Thus, it should be replaced if there is an issue. It's important when working on or near to an engine to make sure the equipment is powered off and completely cooled down before starting any repairs. For more accurate information on how and where to install this recoil starter assembly, reference the appropriate owner's manual and specific equipment diagrams.This is an authentic OEM replacement part made of high-quality materials. This recoil starter assembly can be used with different models of line trimmers that have been manufactured by MTD, Craftsman, Troy-Bilt, and other brands. Part sold individually.

The main drive shaft that the gearbox is attached to is called the drive shaft housing assembly. It connects the power source from the device to the top of the tool. The motor or engine's power runs through the drive mechanism to power the head to rotate while working. The metal piece is used to turn the gearbox in various types of lawn equipment, including blowers and trimmers from several different manufacturers. Signs that a replacement part is necessary may include poor performance or excessive vibration while in operation. Over time, the drive shaft will wear out from normal use or it can become damaged.The replacement of a drive shaft housing assembly is simple with the proper screwdriver and pliers. Replacement involves unscrewing the drive shaft housing from the throttle assembly. Remove the two screws holding the shaft in place. Screw in the new replacement part.The drive shaft housing assembly is supplied directly from the manufacturer and is a genuine OEM part. It is sold separately and individually. The replacement part can be used in MTD, Troy-Bilt, Bolens, and Yard Machines brand equipment. It is compatible with both blowers and trimmers. The piece is made from high-quality, durable materials.

This screw and nuts set is a genuine MTD part, sold individually. This screw and nuts set can be used as a replacement part in a string trimmer. This set provides a variety of screws and nuts which serve as fastening components within the string trimmer.The screw and nuts set in a string trimmer might have to be ordered as a complete replacement part if one or more screws or nuts in the string trimmer has been lost, misplaced, or damaged. If this occurs, the screw and nuts set should be ordered as a genuine OEM replacement part.Sourced directly from the manufacturer, this component is a genuine replacement part that is sold individually. This screw and nuts set is compatible with the following outdoor appliance brands: MTD, Craftsman, Cub Cadet, Troy-Bilt, Murray, Yard Machines, Bolens, and Yard Man.

This is a gear box assembly that is a part of many types of gasoline-powered string trimmers. The gear box assembly is attached to the lower boom assembly. The purpose of the component is to spin and drive the trimmer head to cut through weeds and grass. The gear box assembly is attached to the string trimmer by two screws. This assembly comes with a trimmer head.If the gear box assembly has been damaged and needs to be replaced, a screwdriver will be needed. Place the string trimmer on a level surface and disconnect the spark plug wire for safety. Use a screwdriver to remove the screws from the old gear box assembly so it can be taken off. Use new screws to install the replacement component. Retighten the screws before use.This is an authentic OEM replacement component that is sourced directly from the manufacturer. It is sold as an individual part. The gear box assembly is designed to be used with string trimmers manufactured by MTD, Bolens, and Yard Machines.

This o-ring is a genuine OEM part sourced from the manufacturer for use in many parts of engines in lawn and garden equipment. The o-ring is a type of gasket but is not flat like a gasket. It is circular and made of rubber. It is seated in a groove on the engine part and is compressed against another part to create a seal. This seal keeps air and fluids from entering or exiting the sealed part. Like gaskets, o-rings must be periodically inspected and replaced to ensure proper engine performance.Visual inspection of o-rings will reveal nicks, indentions, cuts, or tears on the surface of the o-ring. If the rubber has warped due to excessive heat, it will not fit properly and will need to be replaced. The replacement may not require tools, depending on the location of the rubber gasket. Remove the bad o-ring and wipe both sides of the area to remove the old grease. Apply fresh grease to the o-ring before installing it to ensure a tight seal. Press the new o-ring firmly in the groove before attaching the connecting part. If the ring does not seat well or has to be stretched to fit, discard and start with a new o-ring.The o-ring is sold individually. It is designed for trimmers and tillers. It is compatible with Craftsman, MTD, Bolens, Troy-Bilt, and Cub Cadet.

The design and purpose of the O-ring is relatively self-explanatory. It is an “O” shaped ring used as a gasket in lawn and garden equipment. It is designed to sit within a groove and be compressed during assembly. It creates a perfect seal that blocks the path of liquids or gases from escaping or flowing into regions of the machine where they are not supposed to be.The O-ring may be damaged if an outdoor piece of equipment is struggling to start or run. After checking the air filter cover, removing the carburetor, and cleaning it thoroughly, the next step is to replace the O-rings, carburetor gasket, and air filter, followed by the spark plug. Regular maintenance of the carburetor and routine evaluation of the suitability of the O-ring is essential to proper mechanical maintenance.This O-ring is a genuine OEM part sourced directly from the manufacturer, and it is sold individually. The manufacturer of this product is MTD. Examples of compatible products and machines includes trimmers, tillers, weed wackers, brush cutters, and leaf blowers or leaf vacuums. It is compatible for products made by the following brands: MTD, Cub Cadet, Craftsman, and Troy-Bilt.

This replacement part is a boom assembly. It is a genuine replacement part made by MTD. This specific part is typically found in line cutters and edgers. The part is able to connect the top of the appliance to the bottom where the blades are located. This is so the user is able to operate the machine from the standing position and control the user settings as needed.A new boom assembly might be needed if the user notices that the current one is damaged in any way including being dented or cracked. It is important that this part is in working condition or the user might not be able to perform the necessary duties. This part is sold individually and is sourced directly from the manufacturer to ensure proper fit. This boom assembly is a genuine OEM replacement part.

This blade guard assembly is an OEM replacement part sourced directly from the manufacturer for use on trimmers to protect the user from the trimmer line as it spins. The blade guard is a plastic part that rocks and flying debris can damage. It can also be damaged by the elements, such as intense summer heat that causes it to crack. If the blade guard is damaged or missing, the trimmer should not be used until it is replaced. Before removing the blade guard and installing a new one, make sure the spark plug is out of the trimmer to prevent accidental powering. Remove the screws from the old blade guard and set them aside. Line the screw holes up on the new blade guard with the screw holes on the trimmer. Insert the screws from the old trimmer and tighten. Reinstall the spark plug. Test the blade guard to make sure it works. This blade guard is a black, molded plastic part that is sold individually. This blade guard is designed for use on trimmers manufactured by Craftsman and MTD.

This part is a replacement short block. This is a genuine OEM part made by MTD and has been sourced directly from the manufacturer. If the current short block is broken or malfunctioning, this part can be used as a replacement. It is intended for use with a variety of line trimmer models. The short block houses important components of the equipment's engine such as the pistons and the engine block. Thus, if this part is malfunctioning, it may prevent the line trimmer from being usable and should be replaced. When working on or near an engine, always ensure that the equipment is powered off and completely cooled down before attempting to undergo any repairs. For more accurate information on how and where to install this short block, the appropriate owner's manual and equipment diagrams should be referred to. This short block is suitable for use on a variety of line trimmer models manufactured by MTD, Craftsman, Cub Cadet, Troy-Bilt, and other brands. It is a genuine OEM part and thus is made of high-quality, durable materials. Part sold individually.