Parts for Thermador POD30201: Bottom Door Parts

This replacement inner door panel restores the dishwasher door's internal liner and support structure for a clean, functional interior. It's the direct-fit inner door component used when the door liner is damaged or dented. What it does

• Replaces a cracked, dented, or corroded inner door liner to restore door integrity
• Helps the door close and seal properly by providing correct internal support
• Prevents interior moisture intrusion and protects insulation and wiring from exposure
• Restores interior appearance where the liner is scratched, bent, or otherwise damaged

• Disconnect power and water supply before beginning any repair
• Removal typically requires opening the outer door panel and removing retaining screws/fasteners; handle edges carefully
• Keep track of clips, screws, and insulation; reassemble in the original order

The Oven Door Seal is an OEM part for Bosch ovens and ranges. This door seal fits snugly around the outer edge of the oven door to provide an effective air seal when closed.

Causes of a bad door seal can include damage from normal wear and tear over time, compression from repeated opening and closing of the door, or heat exposure leading to cracking or warping.

Symptoms of a bad door seal include:

• Inefficient or slow heating
• Inability to maintain set oven temperature
• Increased energy costs
• Smoke escaping around door edges when baking

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

This replacement glass panel restores the smooth, protective surface on the appliance when the original panel is cracked or broken. It helps maintain a clean appearance while shielding the components mounted behind the glass. What it does:

• Forms the visible glass surface on the appliance
• Protects internal components from spills and debris
• Restores a clean, finished look after breakage or heavy scratching
• Common fix for cracked, chipped, shattered, or missing glass

• 1 glass panel

• Disconnect power (and gas, if applicable) and allow the unit to cool completely
• Wear cut-resistant gloves; handle glass carefully
• Transfer any brackets, trim, or seals from the original panel as instructed
• Do not overtighten fasteners; verify proper alignment before restoring power

This trim plate is a decorative front trim piece that restores the finished appearance of your appliance and covers the seam between control panels or door edges. It helps keep edges sealed and improves overall aesthetics. What it does:

• Provides a finished, factory look by covering exposed gaps or seams
• Protects underlying edges from dust, dirt and light impacts
• Helps maintain alignment and appearance around the control/door area
• Commonly replaced when the original trim is scratched, dented or warped

• Disconnect power to the appliance before starting any work.
• Installation typically requires removing adjacent trim or screws; keep fasteners for reuse.
• Handle painted or chrome finishes carefully to avoid scratches; use gloves if available.

This replacement glass panel restores the visible door surface on compatible BOSCH appliances, helping repair cracks, chips, or scratches and returning the door to proper cosmetic condition. Use to replace broken or damaged door glass. What it does:

• Serves as the exterior/interior glass surface of the appliance door
• Replaces cracked, chipped, scratched, or otherwise damaged door glass
• Restores the door's appearance and supports proper door assembly fit
• Helps prevent direct exposure of internal components that damaged glass might allow

• Turn off power to the appliance and disconnect power before beginning service
• Handle the glass carefully; wear cut-resistant gloves and eye protection
• Door disassembly is commonly required — follow the manufacturer's service manual
• Do not use if shipping damage is evident; contact seller before installation

This shaped handle cap covers the end of a dishwasher door handle to restore a finished look and protect the handle connection. It keeps the door appearance consistent and hides the fastener area for a clean, finished fit. What it does:

• Replaces a damaged, cracked or missing handle end cap to restore appearance
• Covers and protects the handle mounting point from dirt and wear
• Prevents sharp edges or exposed fasteners on the door handle
• Matches the original profile so the handle closes and looks correct

• High-level replacement; may require removal of the door trim or handle screws—refer to your model's service instructions
• Disconnect power and water to the appliance before starting work to avoid injury
• Handle with care to avoid scratching painted surfaces; use appropriate trim tools if needed
• If fasteners are damaged, inspect and replace them with OEM-recommended hardware

This shaped handle cap covers and finishes the end of a compatible appliance handle, restoring a clean appearance and helping protect the handle edge from wear. Fits as a direct replacement for a worn, cracked, or missing end cap. What it does:

• Covers the exposed end of the handle for a finished, factory look
• Protects the handle end from chips, scratches, and snagging
• Helps keep the handle grip comfortable and secure
• Restores cosmetic appearance after impact or wear

• Installer tip: this cap typically snaps or slides into place; remove any broken pieces before installing
• Use a plastic trim tool or gloved hand to avoid scratching surrounding surfaces
• Do not force excessively; if the cap does not seat easily, inspect the handle for damage or mounting clips

This replacement door handle restores a secure grip for opening and closing your appliance door. It replaces a damaged, cracked, or loose handle to make the door easy and safe to use again. What it does:

• Provides a sturdy grip for opening and closing the appliance door
• Replaces handles that are cracked, broken, loose, or missing
• Helps restore proper door operation and user safety
• Matches the original mounting points for a direct-fit replacement

• Designed for direct replacement; verify alignment with existing mounting holes before installing
• Use appropriate hand tools; do not overtighten fasteners to avoid cracking the handle
• Disconnect power to the appliance if installation requires removing access panels or working near electrical components