Parts for Dcs BFG-30BS-L-70847: Burner Parts

A replacement D-shaped burner cap that restores even flame coverage and protects the burner head on compatible gas cooktops. Use this cap to improve ignition reliability and maintain correct heat distribution for safer cooking. What it does:

• Covers the burner head to direct flame and promote even heating across cookware
• Helps prevent uneven ignition, sputtering flames, or weak burners caused by damaged or missing caps
• Protects the burner head from spills, debris, and wear that can interfere with performance
• Matches the OEM geometry for proper alignment and flame pattern when seated correctly

• One D-shaped burner cap

• Turn off the cooktop gas supply and ensure the surface is cool before removing or replacing the cap
• Lift the old cap straight up; place the new cap onto the burner post, ensuring it sits flat and centered
• Clean burner head and ports of debris before installing the new cap to ensure proper flame

This ignitor kit replaces the burner spark electrode and its retainers, restoring dependable ignition. It produces a focused spark at the burner so the gas lights quickly and consistently. What it does:

• Generates the high-voltage spark needed to ignite gas at the burner
• Retaining spring and clip hold the electrode in the correct position for reliable ignition
• Helps address: burner won't light, intermittent or weak spark at a burner, or a cracked/chipped electrode insulator

• 1 ignitor (spark electrode), 1 retaining spring, 1 clip

• Disconnect electrical power and shut off gas; allow the appliance to cool before servicing
• Remove burner components to access the electrode; release the clip/spring and withdraw the old ignitor
• Transfer the spark lead to the new electrode; handle the ceramic insulator carefully to avoid damage
• Seat the electrode and secure with the spring and clip; align the tip per service guidelines and test for spark before reassembly

The JET HOLDER D, DMS #47 is an OEM part for Fisher & Paykel gas ranges and cooktops. It securely holds the jet orifice that meters gas flow to one of the rear burners.

Causes generally involve wear and environmental degradation over extended use. Mineral buildup or cracks in the plastic material interfere with precise flow control.

Symptoms of a problematic jet holder can include:

• Unstable or irregularly sized rear burner flames
• Burner response abnormal when adjusting heat settings
• Inability to achieve expected flame sizes on one rear burner
• Potential gas leaks at the jet holder connection point

The Nut M22 Jet Holder is an OEM part for Fisher & Paykel gas ranges and cooktops. This jet holder supports the burner caps and jets that emit gas to the flames. It helps properly distribute gas to each burner element, ensuring an even burn.

Causes of a bad jet holder can include warping or cracks from high heat that disrupt gas flow. Mineral buildup within the holder's jet openings is also common over many years of use.

Symptoms of a bad Nut M22 Jet Holder include:

• Uneven or abnormal flame patterns from burner elements
• Difficulty achieving or maintaining burner flame height
• Potential gas leaks at jet connections
• Dirty or sooty flame that creates excess residue
   

This replacement cooktop grate restores stable support for pots and pans on your range, helping cookware sit level and preventing wobble or uneven cooking. Designed to match OEM fit and finish for a direct swap. What it does:

• Provides a stable cooking surface so pots and pans sit securely over the burner
• Replaces chipped, cracked or misshapen grate that causes wobbling or instability
• Helps maintain proper burner flame distribution by keeping cookware centered
• Restores cooktop appearance when enamel or coating is damaged

• Allow the cooktop to fully cool and turn burners off before removing or installing the grate
• Lift out the old grate and set the new grate into the same position; no special tools typically required
• Inspect burner caps and cooktop surface for debris before reinstalling to ensure a level fit

This rubber bumper cushions and stabilizes appliance panels and doors to reduce noise, vibration, and wear. It helps prevent metal-on-metal contact and keeps moving parts from rattling for quieter, smoother operation. What it does:

• Absorbs shock and dampens vibration between parts
• Prevents panels, doors, or racks from banging or rubbing
• Protects finishes by creating a soft contact point
• Helps maintain proper alignment of movable components

• Disconnect power or gas supply to the appliance before servicing
• Remove the old bumper and clean the mounting surface before installing
• These bumpers are typically installed by pressing into a hole or seating against a surface; follow the OEM instructions for your model
• If adhesive is required, use only the manufacturer-recommended adhesive and allow proper cure time