Parts for Electrolux E36GC76PRS4: Burner Parts

The Switch Assembly is an OEM part for Frigidaire cooktops. It contains the burners’ control switches which allow for selecting different heat settings and operating individual cooking zones. As internal electronic components, these switches can experience wear over time from regular use.

Symptoms of a bad switch assembly include:

• Difficulty turning knobs or selecting desired heat levels  
• Knobs that stick or do not rotate smoothly
• Inoperable or unreliable burner control response
• Burners that will not ignite or heat as directed

Causes of switch failure generally relate to high heat, moisture exposure, and the sheer volume of cycles accumulating from years of cooking use. Over time, electronics may degrade or components like contact points could corrode.

This OEM Frigidaire replacement part is compatible with Electrolux, Gibson, Kelvinator, and Kenmore models. 

The Ignitor Screw is an OEM component for Frigidaire ranges and ovens. It secures the igniter, a critical heating element that sparks to ignite the gas burner. 

Causes of a bad ignitor screw can include damage or stripping of the screw head from repeated removal/installation of the igniter component over time.

Symptoms of a bad ignitor screw include: 

• The igniter shaking loose and becoming disconnected
• Inability to properly tighten the igniter securely in position
• Lost or stripped screw

This genuine Frigidaire replacement screw restores secure mounting of the igniter. Proper fastening is necessary for consistent and reliable ignition of cooking appliances.

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

Replacement mounting bracket that secures internal appliance components to the cabinet or frame, restoring proper alignment and support. Helps reduce rattling and prevents loose or sagging parts for safer, quieter operation. What it does:

• Secures components or assemblies to the appliance frame to maintain proper alignment.
• Reduces movement and vibration that commonly cause rattling or intermittent contact.
• Helps prevent sagging or misalignment of attached parts that can affect operation.
• Simple, passive part — no electrical function.

• Disconnect power (and water, if applicable) before starting any repair.
• Use appropriate hand tools; inspect mounting holes and fasteners for damage or corrosion.
• Replace only the damaged bracket; do not overtighten fasteners to avoid cracking.

This is a ceramic glow-bar igniter for gas ovens. It heats to ignite the gas for baking or broiling, restoring reliable oven lighting and even heating without repeated clicking or open flames.

• Heats up to light the gas burner in the oven cavity
• Common fix for oven not heating, long preheat times, or burner that lights then goes out
• Designed for ovens that use a glow-bar (hot surface) ignition system

• Disconnect power and shut off gas before servicing
• Handle the ceramic element carefully; avoid touching the carbide tip
• Test for proper ignition and observe a full heat cycle after installation

This glow-bar ignitor is the heat source that lights the oven or range burner so gas can ignite, restoring reliable burner ignition and oven heating when the original element fails. What it does:

• Heats to ignition temperature to allow the gas safety valve to open and the burner to light.
• Commonly replaces a cracked, broken, or non-glowing element that prevents the oven from heating.
• Can stop clicking, long-light delays, or uneven heating caused by a failing ignitor.
• Designed to match the original mounting and connector style for a direct replacement.

• One ignitor (glow-bar) — exact item shown.

• Disconnect power and shut off the gas supply before starting any repair.
• Handle the ceramic/glass element carefully—avoid dropping or touching the glowing surface with bare hands.
• If connectors are corroded, clean or replace them; do not force-fit the ignitor.

The Ignitor is an OEM part for Frigidaire cooktops. It provides the spark necessary to ignite the gas on your range's surface burners. It generates a spark to ignite the gas flowing to the burner, ensuring a consistent and safe flame.

A bad ignitor can be caused by wear and tear, damage, or electrical issues. Signs of a faulty ignitor include the burner not lighting or a weak or inconsistent spark.

Symptoms of a bad ignitor include:

• Burner not lighting or requiring multiple attempts to ignite
• Weak or inconsistent spark 
• Visible damage to the ignitor, such as cracks or breaks

This Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.
 

This is a surface burner head for a gas range/cooktop. It distributes gas from the orifice to the burner ports, helping deliver an even flame and reliable ignition when the original head is clogged, damaged, or corroded.

• Channels gas through precision ports to create a stable, even cooking flame
• Works with the burner cap and igniter for quick, consistent lighting
• Typical symptoms: burner won't light or takes multiple clicks, uneven/yellow flames, weak flame, or popping/flare-ups
• Physical issues may include blocked ports, heavy corrosion, or a warped/stripped casting

• Disconnect power and shut off gas; let the cooktop cool completely
• Lift off the burner cap; remove mounting screw(s) if present and lift off the old head
• Clean mating surfaces/orifice area; set the new head squarely and secure with existing hardware
• Restore gas and power; verify proper ignition and flame pattern

This replacement surface burner head restores a steady, even flame on your gas cooktop. It mixes gas and air and distributes the flame evenly to help ensure reliable ignition and consistent cooking performance.

• Mounts over the orifice and channels gas/air through flame ports for even heating
• Helps resolve weak, uneven, or yellow flames and delayed ignition
• Can address clicking without lighting or burners that won't stay lit
• Durable cast construction designed for repeated heating cycles

• Disconnect power and shut off gas; allow the appliance to cool completely
• Remove grates and access the burner per your model; transfer any mounting hardware from the old part if needed
• Seat the new burner head squarely over the orifice and ensure proper alignment
• Restore gas and power; test for proper ignition and flame. If any gas connections were disturbed, check for leaks with soapy water.

This burner restores proper flame distribution and ignition performance in your gas cooking appliance, helping you achieve steady, even heat for reliable boiling, simmering, and searing. What it does:

• Directs gas from the orifice through burner ports for an even flame pattern
• Works with the igniter/electrode to light the burner
• Helps reduce symptoms like uneven or weak flame, delayed ignition, or flame that lifts or makes popping noises
• Can address issues where the burner won't light or only lights partially due to damage or blockage

• 1 burner

• Disconnect power and shut off gas before servicing
• Access the burner per your model's service instructions; transfer any required hardware from the old part
• Ensure proper alignment with the igniter and orifice; tighten fasteners securely
• Restore gas and power, then inspect flame; check for leaks if any gas fittings were disturbed

This ignitor orifice assembly routes gas to the burner so the ignitor can light the flame, restoring reliable ignition and efficient burner operation. It's a direct-replacement style part used on compatible gas ranges and ovens. What it does

• Controls and meters gas flow to the burner orifice so the ignitor can ignite the burner
• Restores consistent ignition when a faulty orifice prevents the burner from lighting
• Can correct weak or intermittent flames caused by a damaged or clogged orifice
• Works as part of the burner/ignition system

• One ignitor orifice assembly

• Turn off the appliance power and shut off the gas supply before starting work
• Handle and seat the orifice assembly carefully; do not overtighten fittings
• Check for proper sealing and ignition after installation; if you detect a gas smell or suspect a leak, shut off gas immediately
• If you are not comfortable working on gas appliances, have the part installed by a licensed service professional

The Regulator is an OEM part for Frigidaire cooktops. It is responsible for regulating the flow and pressure of gas entering the appliance, ensuring safe and efficient operation.

A bad regulator can be caused by faulty internal components, wear and tear over time, or damage due to improper handling. Signs of a faulty regulator include uneven heating, weak flame, or gas leaks.

Symptoms of a bad regulator can include:

• Uneven heating of burners or oven 
• Weak or inconsistent flame 
• Gas leaks around the regulator 

This Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

These are replacement countertop mounting screws that secure the appliance to the countertop or cabinet, restoring a stable, flush fit and preventing movement or gaps. Sold as a 2-pack for quick, direct replacement. What it does

• Secures the appliance countertop or trim to the cabinet or counter to keep the unit from shifting.
• Helps eliminate rocking, gaps, or uneven alignment caused by missing or loose mounting screws.
• Restores proper fit and finish where original mounting hardware has been lost or damaged.
• Works with factory mounting points and standard driver heads for straightforward replacement.

• Two countertop mounting screws.

• Use the correct-size driver to avoid stripping the screw head.
• Tighten until snug; avoid over-tightening which can strip threads or damage the cabinet/countertop.
• Keep original brackets and hardware; replace only the missing or damaged screws as needed.