Parts for Frigidaire FPGH3077RFC: 03 - Burner Parts

The Valve is an OEM part for Frigidaire gas ranges. It is the mechanism located behind each burner that regulates the flow of natural gas into the burner venturi tubes. 

Causes of a bad gas valve can include wear from repeatedly opening and closing over extended use. Internal components may degrade or fail to properly seal.

 Symptoms of a bad gas valve include:

• Inconsistent burner flame levels  
• Difficulty adjusting flame heights 
• Burners failing to ignite or stay lit as expected
• Gas leaks detected around valve areas

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This water inlet valve controls water flow to the refrigerator's dispenser and ice maker so you get a steady supply when needed and stop unwanted leaks. Replaces a worn or faulty valve to restore proper fill and dispensing. What it does

• Opens and closes to allow water into the ice maker and dispenser when requested
• Stops water flow to prevent overfilling or continuous running
• Commonly replaced when dispenser or ice maker won't fill, has weak flow, or leaks
• Works with the refrigerator's water line and solenoid actuators to meter supply

• One water inlet valve (single unit as shown)

• Disconnect power and shut off the household water supply before starting
• Drain lines and remove front or rear access panels to reach the valve
• Inspect and replace any damaged water lines or fittings; tighten connections and check for leaks after installation

The Burner Valve is an OEM component specifically designed for Frigidaire ranges. It controls gas flow to individual burners, providing a selection of different heat levels when operating the cooktop.

Causes of a bad burner valve can include wear over extended usage periods, damage from water, or gas blockage impeding operation. 

Symptoms of a bad burner valve include:

• Inability to light specific burners or adjust the flame height
• Uneven or intermittent burner performance  
• Gas leaks at burner valve connections
• Recurring error codes due to valve malfunctions

Replacing with this OEM valve restores full functionality to the range cooktop. Compatible with existing gas lines, it supports safe and reliable cooking performance.

This OEM Frigidaire replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models. Replace before issues worsen.
 

This water inlet valve controls water flow to the refrigerator's dispenser and ice system so you get a steady supply when needed and stop unwanted leaks. It replaces a worn or failing valve to restore proper water delivery. What it does:

• Opens and closes to allow water into the ice maker and dispenser
• Stops water flow when dispenser/ice fill is inactive
• Commonly replaced when water won't dispense or ice maker won't fill
• Needed if the valve is leaking or causing water drips

• Disconnect power and shut off the water supply before replacing the valve
• Handle with care and inspect inlet/outlet fittings and gaskets for proper sealing
• Reconnect water and power, then check for leaks and proper water flow after installation
• Follow manufacturer instructions

The Ignitor Screw is an OEM component for Frigidaire ranges and ovens. It secures the igniter, a critical heating element that sparks to ignite the gas burner. 

Causes of a bad ignitor screw can include damage or stripping of the screw head from repeated removal/installation of the igniter component over time.

Symptoms of a bad ignitor screw include: 

• The igniter shaking loose and becoming disconnected
• Inability to properly tighten the igniter securely in position
• Lost or stripped screw

This genuine Frigidaire replacement screw restores secure mounting of the igniter. Proper fastening is necessary for consistent and reliable ignition of cooking appliances.

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

This surface burner element replaces a damaged or non-working electric cooktop heating element to restore normal cooking heat and even heating across cookware. It fits compatible Frigidaire electric ranges and stoves. What it does:

• Heats cookware by converting electrical power into cooking heat for stovetop use.
• Replaces an element that fails to heat, gets intermittently hot, or shows visible burns or breaks.
• Restores even cooking when the original burner is warped, cracked, or has poor contact.
• Works with existing terminal block and cooktop connections when the mount and wiring are intact.

• One surface burner element (single replacement).

• Disconnect power to the range at the circuit breaker before starting any work.
• Allow the cooktop and element to cool completely; element terminals can be sharp—wear gloves.
• Remove the old element by pulling straight out from the terminal block and align the replacement for a snug, secure fit.

This is a surface burner head for a gas range/cooktop. It distributes gas from the orifice to the burner ports, helping deliver an even flame and reliable ignition when the original head is clogged, damaged, or corroded.

• Channels gas through precision ports to create a stable, even cooking flame
• Works with the burner cap and igniter for quick, consistent lighting
• Typical symptoms: burner won't light or takes multiple clicks, uneven/yellow flames, weak flame, or popping/flare-ups
• Physical issues may include blocked ports, heavy corrosion, or a warped/stripped casting

• Disconnect power and shut off gas; let the cooktop cool completely
• Lift off the burner cap; remove mounting screw(s) if present and lift off the old head
• Clean mating surfaces/orifice area; set the new head squarely and secure with existing hardware
• Restore gas and power; verify proper ignition and flame pattern

This replacement surface burner head restores a steady, even flame on your gas cooktop. It mixes gas and air and distributes the flame evenly to help ensure reliable ignition and consistent cooking performance.

• Mounts over the orifice and channels gas/air through flame ports for even heating
• Helps resolve weak, uneven, or yellow flames and delayed ignition
• Can address clicking without lighting or burners that won't stay lit
• Durable cast construction designed for repeated heating cycles

• Disconnect power and shut off gas; allow the appliance to cool completely
• Remove grates and access the burner per your model; transfer any mounting hardware from the old part if needed
• Seat the new burner head squarely over the orifice and ensure proper alignment
• Restore gas and power; test for proper ignition and flame. If any gas connections were disturbed, check for leaks with soapy water.

This burner replaces a worn or damaged unit on your range to restore reliable, even heat. Swap it in to correct poor performance caused by cracks, corrosion, or blockages so cooking results return to normal.

• Provides the heat source for a cooking zone on the range
• Common fix for damage, warping, or clogged ports/passages
• Symptoms include won't light/heat, weak or uneven heating, or irregular/yellow flame on gas models
• Visible rust, cracks, or deformation indicate replacement is needed

• Disconnect power; for gas models, also shut off the gas supply. Allow the appliance to cool completely
• Remove grate/cap or unplug element as applicable; take out screws/retainers to lift off the old burner
• Transfer reusable items from the original part (such as cap, electrode/igniter, and screws) if required by your model
• Align correctly and tighten fasteners evenly; restore utilities and test for proper operation

This burner restores proper flame distribution and ignition performance in your gas cooking appliance, helping you achieve steady, even heat for reliable boiling, simmering, and searing. What it does:

• Directs gas from the orifice through burner ports for an even flame pattern
• Works with the igniter/electrode to light the burner
• Helps reduce symptoms like uneven or weak flame, delayed ignition, or flame that lifts or makes popping noises
• Can address issues where the burner won't light or only lights partially due to damage or blockage

• 1 burner

• Disconnect power and shut off gas before servicing
• Access the burner per your model's service instructions; transfer any required hardware from the old part
• Ensure proper alignment with the igniter and orifice; tighten fasteners securely
• Restore gas and power, then inspect flame; check for leaks if any gas fittings were disturbed

This ignitor orifice assembly directs gas to the oven igniter so the burner lights reliably. It replaces a worn or clogged orifice assembly to restore consistent ignition and help the oven heat as expected. What it does:

• Delivers gas to the igniter so the burner can ignite
• Helps maintain a steady flame for normal oven heating
• Common fix for ovens that fail to light, only light intermittently, or take long to ignite
• Works as the gas-orifice/ignitor interface in the oven's ignition system

• One ignitor orifice assembly

• Turn off the gas supply and disconnect power before servicing
• Follow OEM instructions; use proper fittings and pipe-sealant rated for gas connections
• Inspect connections for leaks after installation and test functionality

This ignitor orifice assembly delivers and directs gas to the oven ignitor so burners light reliably. It restores proper gas flow at the ignitor for consistent ignition and safer oven operation in gas ranges and wall ovens. What it does:

• Directs gas from the valve to the oven ignitor so the burner can ignite
• Helps eliminate no-heat or weak-flame symptoms when the ignitor area is the issue
• Supports stable, consistent ignition timing and flame establishment
• Replaces a damaged, clogged, or corroded orifice/ignitor connection

• One ignitor orifice assembly

• Turn off gas supply and electrical power before beginning work
• Handle carefully; avoid bending the orifice and keep ignition surfaces clean
• Basic hand tools are typically required
• After installation, check for gas leaks and test oven ignition in a well-ventilated area

This ignitor orifice assembly supplies the gas and spark alignment needed to light an oven or range burner, restoring reliable ignition for safe, consistent cooking performance. What it does:

• Delivers the correct orifice positioning and ignitor alignment so the burner lights when the oven calls for heat.
• Helps eliminate delayed ignition, clicking without flame, or weak/uneven burner lighting when failure is caused by the orifice/ignitor assembly.
• Works as the mechanical/electrical interface between the gas supply and the ignitor for safe ignition.
• Compatible with common oven/range ignition systems that use a separate orifice and hot-surface/spark ignitor assembly.

• Shut off power and gas supply before beginning service; confirm both are off.
• Handle the ignitor carefully (it is fragile); avoid touching the ceramic or heated surfaces with bare hands.
• Use proper tools and follow the appliance manufacturer's service manual for alignment and torque specifications.
• After installation, restore gas and power and perform a leak check and test cycle to confirm correct ignition and safe operation.

This ignitor orifice assembly delivers the metering and mounting needed for reliable gas ignition in compatible ovens and ranges. It replaces a worn or damaged orifice assembly to restore consistent burner lighting and safe operation. What it does:

• Directs and meters gas to the ignitor so the burner can light reliably
• Replaces a cracked, clogged, or corroded orifice that causes ignition failure
• Helps stop intermittent ignition and reduces delayed or no-light conditions
• Works with the oven/range ignition system to support consistent flame start-up

• Turn off gas supply and electrical power to the appliance before starting work
• Installation involves accessing the burner/ignitor area—follow the appliance service manual
• Tighten fittings to manufacturer torque specs and check all connections for leaks with a leak test solution

This ignitor orifice assembly secures the oven igniter and directs gas to the oven burner for consistent ignition. It's a direct-replacement part used to restore proper spark/ignition performance on compatible gas ovens. What it does:

• Holds and positions the oven igniter and orifice for reliable flame initiation
• Directs gas flow to the burner so the igniter can light the oven
• Commonly replaces worn, clogged, or damaged assemblies that cause ignition delays or no-heat conditions
• Helps restore safe, consistent oven ignition when the igniter itself is functioning

• Disconnect power and shut off the gas supply before beginning any service
• Handle components carefully; avoid bending or damaging the orifice or ignitor mounting

The Regulator is an OEM replacement part for Frigidaire gas ranges and cooktops. It is a valve component that regulates gas flow from the supply line into the appliance burners. Carefully controlling fuel input maintains proper and safe burner flame sizes.

Symptoms of a bad regulator include:

• Burners producing uneven or excessively high flames
• Inability to reduce burner flames properly  
• Gas leaks at the regulator connections

Causes of failure involve wear of internal sealing parts over extended use. Corrosion or debris clogging gas passages can also disrupt flow regulation.

This OEM Frigidaire replacement regulator ensures optimal and reliable burner performance. Compatible with some Amana, Electrolux, and KitchenAid models as well, regular replacements prevent dangerous gas line issues from developing. 

The Valve is an OEM replacement part for Frigidaire ranges. Located along the gas line leading to the oven burners, it regulates gas flow and controls burner ignitions. Proper valve function is critical for safe and efficient cooking performance.

Causes of a bad valve can include wear from prolonged use, corrosion or clogging of small internal passages over many years. Damage may also occur if exposed to extreme heat or sudden temperature changes.

Symptoms include: 

• Inconsistent or intermittent burner ignition  
• Flames that fluctuate in size or temperature
• Gas leaks around connections that develop
• Failure of the oven or burners to ignite properly

Compatible models include Electrolux, Gibson, and select Kenmore ranges. 

This replacement surface burner restores stovetop heating for electric ranges, providing a direct, reliable heat source for pots and pans. Designed to match the original element shape and fit for a straightforward swap. What it does:

• Heats cookware on the cooktop so you can boil, simmer, and sauté
• Replaces a cracked, warped, or non-heating burner element
• Addresses symptoms such as little or no heat, intermittent heating, or uneven hot spots
• Works with the existing burner receptacle and cooktop cutout when the correct element is used

• One round surface burner element

• Disconnect power to the range before servicing to avoid electrical shock
• Remove the cooktop or lift the burner assembly per your model's service instructions
• Align and seat the element into the socket, then secure any mounting clips or screws as originally installed

The Broil Igniter is an OEM part for Frigidaire gas ranges. It is the component responsible for igniting the broil burner located at the top of the oven cavity.

Without a functioning igniter, the broiler cannot be used to cook or brown food directly under the heating element. Over extended use at high broiler temperatures, igniters can degrade and crack rendering them unable to create the required electric spark.

Causes for replacement include standard wear over time or impact damage occurring during cleaning that compromises the integrity of the igniter.

Symptoms of a bad broil igniter are:

• Inability to light or reignite the broiler burners
• Error codes or messages related to ignition issues
• Broiler component that looks dark, worn, or broken

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The Ignitor is an OEM replacement part for Frigidaire gas ranges. Located near the burner heads, this component is responsible for generating the electric spark required to light stove top burners.

Symptoms of a faulty ignitor include:

• Burners that will not light or only light intermittently
• Clicking noises but no flame ignition
• Diminished or no spark from the ignitor itself

Causes of ignitor failure can be an accumulation of deposits over many heating cycles. Physical damage from pots/pans is also possible. As electrical parts, ignitors have a limited lifespan depending on range usage.

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The Screw is an OEM part for Frigidaire ranges and cooktops. This part secures the burner head in place, ensuring proper alignment and functioning of the burner.

Causes of a bad burner head screw can include loosening due to repeated heating and cooling cycles, damage from impact or mishandling, or simply wear and tear over time.

Symptoms of a loose or missing burner head screw include:

• Uneven or irregular flame pattern on the burner
• Burner head not sitting flush or properly aligned
• Burner head wobbling or moving during use
• Potential gas leaks if the burner head is not securely fastened

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This valve mounting screw secures refrigerator water/ice valve assemblies and their mounting brackets, helping keep the valve stable and properly aligned. A simple replacement to address loose or vibrating valve hardware. What it does:

• Secures the valve mounting bracket to the appliance cabinet or valve body
• Fits standard 1/4-20 threaded valve mounting points
• Restores secure mounting when original screw is loose, missing, or stripped
• Helps reduce vibration-related noise and the risk of valve movement that can lead to leaks

• Disconnect power and shut off the water supply before servicing
• Start the screw by hand to avoid cross-threading, then tighten until snug
• Do not over-tighten; replace if threads are stripped or damaged

This LP conversion kit lets a compatible gas range or oven be converted from natural gas to liquid propane, restoring proper burner performance and safe operation when using LP fuel. What it does:

• Replaces factory natural-gas orifices and components so burners run correctly on liquid propane
• Helps correct yellow or lifting flames, weak or uneven burners, or hard lighting caused by using the wrong fuel orifices
• Ensures fuel delivery is sized for higher-pressure propane versus natural gas
• Supports safe switching between fuel types when used per the manufacturer's instructions

• LP conversion kit components

• Installation must follow the OEM instructions exactly; keep original parts and documentation
• Shut off the gas supply before beginning work and test all fittings for leaks after installation
• Do not operate the appliance until conversion is complete and burner flames are verified safe

This wiring harness routes power and control signals between appliance components to restore electrical connectivity and reliable operation. It replaces a damaged or faulty connector assembly to help address intermittent power or control issues. What it does:

• Connects control board, switches, and motors with factory-style terminals for secure signal and power transfer
• Restores lost or intermittent electrical connections that can cause controls, displays, or motors to fail
• Prevents arcing and shorts by replacing frayed, burned, or corroded wiring and connectors
• Maintains correct wire routing and connector fit to preserve original appliance operation

• Always disconnect power at the breaker or unplug the appliance before starting work
• Compare the new harness to the old one to ensure connector types and lengths match before installing
• Route and secure wiring as originally installed; avoid pinching or contact with hot surfaces

This is a replacement mounting screw used to secure appliance panels and components. It restores proper fastening to reduce vibration and keep parts aligned for safe, reliable operation. What it does:

• Secures panels, brackets, and trim to prevent rattling or loosening
• Restores proper fit where a damaged or missing screw caused gaps or movement
• Helps maintain component alignment for smooth operation
• Simple hardware replacement that supports overall appliance stability

• Disconnect power and gas before servicing the appliance
• Use the correct screwdriver or driver bit to avoid stripping the head
• Tighten until snug; do not overtighten to prevent thread or part damage
• Keep small parts away from children and dispose of old fasteners responsibly

The Screw is an OEM part for Frigidaire ranges and ovens. This part is designed to securely fasten various parts of the appliance, ensuring stability and durability. 

Over time, screws can become loose due to the expansion and contraction of materials with temperature changes. Regular use and the occasional necessary removal for repairs or cleaning can also wear down the threads, making them less effective.  

Symptoms of a bad Screw (Chrome) include:

• Loose or wobbly components that should be securely fastened.
• Difficulty in securing parts due to stripped or damaged screw threads.
• Visible corrosion or deterioration of the screw.

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

Size: 8-18 x 0.5 inch. Color: Chrome.

The Screw is an OEM part for Frigidaire ranges and ovens. This part is designed to securely fasten various parts of the appliance, ensuring stability and durability. 

Over time, screws can become loose due to the expansion and contraction of materials with temperature changes. Regular use and the occasional necessary removal for repairs or cleaning can also wear down the threads, making them less effective.  

Symptoms of a bad Screw (Chrome) include:

• Loose or wobbly components that should be securely fastened.
• Difficulty in securing parts due to stripped or damaged screw threads.
• Visible corrosion or deterioration of the screw.

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

Size: 8-18 x 0.5 inch. Color: Chrome.

The Screw is an OEM part for Frigidaire ranges and ovens. This part is designed to securely fasten various parts of the appliance, ensuring stability and durability. 

Over time, screws can become loose due to the expansion and contraction of materials with temperature changes. Regular use and the occasional necessary removal for repairs or cleaning can also wear down the threads, making them less effective.  

Symptoms of a bad Screw (Chrome) include:

• Loose or wobbly components that should be securely fastened.
• Difficulty in securing parts due to stripped or damaged screw threads.
• Visible corrosion or deterioration of the screw.

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

Size: 8-18 x 0.5 inch. Color: Chrome.