Parts for Kenmore 911.3378891 (9113378891, 911 3378891): Burner Section Parts

This small replacement clip secures cabinet insulation in place to help maintain proper thermal performance and reduce vibration. A simple, original-equipment style retainer for restoring insulation fit and keeping internal components covered. What it does:

• Holds appliance insulation against the cabinet or inner panels
• Helps prevent insulation from sagging, shifting, or falling into vents or components
• Can reduce noise caused by loose insulation and help maintain temperature control
• Commonly needed when clips are broken, corroded, or missing

• One insulation retainer clip

• Disconnect power (and water if applicable) before accessing internal panels
• Remove access panels or liners to reach the insulation area; retain fasteners
• Push or snap the retainer into the designated hole/slot; some models may require light prying or a screwdriver for removal
• Wear gloves and eye protection to avoid cuts from sharp sheet metal and insulation fibers

This replacement mounting screw secures panels and trim pieces on compatible appliances to restore proper fit and reduce rattling. Use it to replace missing or damaged screws that keep covers and components fastened. What it does:

• Fastens panels, trim, and small components to the appliance frame
• Restores secure attachment to stop vibration, noise, or loose panels
• Replaces missing, stripped, or corroded screws that prevent proper closure
• Works wherever the original screw type was used for mounting or securing parts

• Disconnect power to the appliance before servicing to avoid shock
• Use the correct screwdriver or bit to avoid stripping the head
• Start threading by hand to ensure proper engagement before tightening
• Do not over-tighten; snug until secure to avoid damaging threads or panels

The Igniter Mounting Screw is an OEM replacement part for GE ovens and ranges. This screw secures the igniter to the burner assembly, ensuring it remains firmly in place for consistent and reliable ignition. Its precise fit and durable design help maintain the stability and functionality of the igniter.

Over time, mounting screws can become corroded, stripped, or lost during repairs or maintenance. A missing or damaged screw may result in a loose igniter, affecting the appliance's ability to ignite properly.

Symptoms of a bad or missing igniter mounting screw include:

• The igniter becoming loose or misaligned

• Difficulty securing the igniter during installation or repair
• The burner fails to ignite reliably or consistently
• Increased noise or movement of the igniter during operation

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

This replacement screw secures appliance components so panels, brackets, and assemblies stay tight and aligned. Replace stripped or missing hardware to eliminate rattles and keep your unit assembled safely and correctly.

• Fastens panels, brackets, or components to the appliance frame
• Restores a secure fit when the original screw is lost, stripped, or corroded
• Helps prevent vibration noise and movement during operation
• Supports proper alignment of trim and assemblies

• Disconnect power; for gas units, also shut off the gas supply
• Use the correct driver to avoid stripping the head; do not overtighten
• Inspect and address damaged mating threads, clips, or brackets before reinstalling
• Refer to your model's parts diagram to confirm location and quantity

This replacement screw secures panels and small components on your appliance to restore proper fit and help prevent rattling or loose parts. Use it wherever the original fastener has been lost or damaged. What it does:

• Secures trim, panels, or mounting brackets to keep components aligned
• Prevents vibration and rattling caused by loose fasteners
• Replaces missing or stripped screws that compromise panel fit
• Restores reliable fastening so doors and controls sit correctly

• Disconnect power before accessing internal panels or components
• Use the correct driver to avoid stripping the screw head
• Thread carefully and do not overtighten to prevent damage
• Keep small parts away from children and pets

Package of 12

This replacement back-right gas tube routes gas from the valve to the rear burner for proper combustion. It restores the correct gas flow path so the burner can light and maintain a steady flame when installed correctly. What it does:

• Directs gas from the valve to the back-right burner for ignition and operation
• Helps achieve a stable, even flame at the rear burner when functioning
• Replaces damaged, bent, or corroded tubing that can disrupt gas flow
• Can resolve symptoms like weak or no flame at the rear burner and uneven heating

• One back-right gas tube

• Turn off gas supply and power before attempting any service
• Inspect fittings and gaskets; replace any worn seals to prevent leaks
• Tighten connections to manufacturer torque specs and test for leaks with a soap solution or gas leak detector

This is a replacement mounting screw used to secure panels and components on compatible appliances. It restores proper fit and prevents rattling or loose parts for a safe, stable appliance. What it does:

• Secures panels, trim, brackets or small components in place
• Replaces missing or stripped fasteners that cause rattling or loose parts
• Helps maintain appliance alignment and safe operation when installed properly
• Small fastener for interior or exterior appliance assemblies

• Disconnect power (and gas if applicable) before servicing the appliance
• Use the correct screwdriver and hand-start threads to avoid cross-threading
• Do not overtighten; snug until secure to prevent stripping or damaging parts

The Pressure Regulator is an OEM part for GE ranges. This part controls and maintains the appropriate gas pressure flowing to the burners, ensuring consistent and safe operation of the stove.

Causes of a bad pressure regulator can include wear and tear over time, exposure to high temperatures, or contamination from dirt and debris. 

Symptoms of a bad pressure regulator include:

• Inconsistent or fluctuating burner flames
• Burners not igniting
• The smell of gas around the range
• Reduced cooking efficiency

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.