Parts for Frigidaire MRT26NNBW0: 04 - Cabinet Parts

This part has been discontinued and is no longer available.

This factory fastener secures appliance panels and components. Replace a missing, stripped, or corroded screw to restore a tight, rattle-free fit and keep brackets and covers properly aligned.

• Fastens panels, brackets, and internal parts as specified by the manufacturer
• Helps maintain alignment and reduces vibration/rattling
• Replace if the head is stripped, threads are damaged, or corrosion is present
• Symptoms include loose/missing hardware, gaps, or rattling during operation

• Disconnect power; shut off gas/water if applicable before servicing
• Use the correct driver/bit size to avoid stripping the head
• Start threads by hand to prevent cross-threading; do not overtighten
• Match screw length/thread to the location; replace in sets when required

This replacement screw secures refrigerator components such as brackets, trims, and covers. Replace missing or stripped hardware to keep parts tight and aligned, helping eliminate rattles and restoring a solid, reliable fit.

• Fastens interior or exterior components to the cabinet or doors
• Replaces missing, rusty, or stripped hardware
• Helps reduce vibration noises from loose parts
• Restores proper fit and alignment of panels, trims, or covers

• Disconnect power; turn off water supply if working near the dispenser or ice system
• Retain and reuse any original spacers or washers
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Replace one fastener at a time to maintain alignment

This replacement white grille plug restores a clean finished look by covering an unused opening in the appliance front grille. It helps keep out dust and small debris while maintaining the grille's appearance. What it does:

• Covers unused grille openings to restore the appliance's finished appearance
• Helps block dust, lint and small debris from entering behind the grille
• Prevents small objects from falling into internal openings
• Snaps into the grille opening to hold trim flush and secure

• High-level: Disconnect power or unplug the appliance before working near electrical components
• Most installs: Push the plug into the grille opening until it snaps or sits flush; no special tools typically required
• If retaining clips resist, gently pry the surrounding trim for access—avoid excessive force to prevent cracking
• Verify proper fit and that the plug sits flush with the grille after installation

A small replacement push-cap that restores the look and function of a control or panel button. Use this plug button when a worn, torn, or missing cap makes controls hard to press or exposes the switch. What it does

• Covers and protects the underlying switch or actuator from dirt and moisture
• Restores a tactile surface for reliable button presses
• Improves appearance when the original cap is cracked, torn, or missing
• Prevents accidental contact with the switch mechanism

• Disconnect power to the appliance before servicing to avoid shock or injury
• Remove the control panel or trim per your model's service instructions to access the button area
• Press the plug onto the switch stem until fully seated; do not force or pry with metal tools
• If the switch underneath is damaged, replace the switch assembly rather than relying on the cap alone

The Crisper Shelf Support is an OEM part for Frigidaire refrigerators. It is designed to hold the crisper shelf securely in place, providing stable support for the storage of fruits and vegetables.

Over time, the crisper shelf support can become worn or damaged due to regular use, heavy loads, or accidental impacts. If the support breaks or fails, it can lead to an unstable or sagging crisper shelf.

Symptoms of a bad crisper shelf support include:

• The crisper shelf not sitting level
• The shelf falling out of place or not staying securely in position
• Difficulty in inserting or removing the crisper drawer
• Visible cracks or damage to the support

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Frigidaire Touch-Up Paint is white in color in a .6 fl oz bottle. For almond order 5303321320. For black order 5303321321.

The Touch Up Paint is an OEM part for Frigidaire appliances. Whether you're dealing with scratches, chips, or other minor cosmetic damage, this touch-up paint provides an easy and effective solution for maintaining the appearance of your appliance. It's designed to adhere well to metal surfaces, offering durability and resistance to further wear and tear.

Over time, appliances can accumulate minor surface damage from regular use, cleaning, and accidental impacts. Using the Touch Up Paint not only improves the aesthetic appeal of your appliance but also helps protect exposed areas from rust and corrosion, which can extend the life of the appliance.

Symptoms of needing Touch Up Paint include:

• Visible scratches or chips on the appliance's surface.
• Areas of rust or corrosion that need to be covered after treating the rust.
• The desire to maintain or improve the appliance's appearance for aesthetic reasons or to maintain its value.