Parts for E522A-21768A: Cabinet Components Parts

The Support Bracket is an OEM component specifically designed for Fisher & Paykel refrigerators. This bracket securely mounts internal shelves, bins, and other removable parts within the refrigerator storage area.  

The bracket must withstand years of shifting shelf loads and accidental impacts without deforming. Over many uses, small defects can accumulate.

Causes of a defective support bracket include stress fractures or damage from misaligned or overloaded shelves putting uneven pressure on mounting points.

Symptoms of a bad support bracket include:

• Loose or sagging shelves that do not stay level  
• Detached shelves or bins that no longer stay mounted
• Broken plastic or bent mounting tabs

This OEM Fisher & Paykel part is also compatible with models from KitchenAid, ProLine, and some Crosley brands. Replacing a damaged bracket helps maintain proper shelving support for your refrigerator.
 

This PC fan assembly replaces the small cooling fan used to move air across the appliance's electronic control board, helping keep electronics cooler and reducing thermal stress for reliable operation. What it does

• Circulates air to cool the main control/PC board and nearby components
• Prevents overheating that can cause control errors or shutdowns
• Reduces fan noise or vibration when a failed fan is replaced
• Restores proper airflow if a burned, seized, or intermittent fan was the issue

• Disconnect power before accessing the control housing or PC board
• Handle the control board and connectors carefully to avoid damage from static or flexing
• Verify fan connector orientation and secure mounting; route wiring away from moving parts

This right-hand retainer slide assembly secures and guides a compatible drawer or panel so it opens and closes smoothly. It replaces worn or damaged slides to restore proper alignment and reliable movement. What it does:

• Holds the drawer/panel in place and keeps it aligned during operation
• Guides smooth in-and-out movement to prevent sticking or uneven travel
• Reduces wobble, rattling, or misalignment caused by a broken or worn slide
• Works as a direct replacement for the corresponding right-side slide assembly

• Disconnect power to the appliance before beginning any repair
• Basic hand tools are typically required; avoid force to prevent plastic damage
• Compare the new part to the original to confirm orientation and fit before installing

This Slide 305 RH assembly is the right-hand drawer slide that guides and supports a refrigerator/freezer drawer for smooth opening and secure alignment. It restores proper drawer movement and helps prevent sagging or binding. What it does:

• Guides the drawer along its track for smooth, even travel
• Supports drawer weight to prevent sagging or tilting
• Keeps the drawer aligned to ensure full opening and closing
• Helps stop sticking, binding, or noisy drawer operation

• Remove contents and fully open the drawer before starting; follow the appliance manufacturer's service instructions
• Use basic hand tools; keep fasteners and clips from the old slide to match orientation
• Check and install the matching left-hand slide if replacing both sides for proper alignment

Left-hand drawer slide assembly that supports and guides a refrigerator or freezer drawer for smooth movement and reliable alignment. Replaces a worn or damaged left-side slide to restore proper drawer glide and support. What it does:

• Guides and supports the left side of a pull-out drawer for smooth opening and closing
• Keeps the drawer aligned and prevents tipping or binding under load
• Restores proper operation when a drawer is hard to open, sticks, or falls out of track
• Works as the left-side mating component in the drawer slide system

• Remove drawer contents and fully support the drawer before removing the old slide
• Use basic hand tools; do not force parts—match mounting points and fasteners
• If wiring or components are adjacent, disconnect power to the appliance before starting

This left-hand hinge base bracket secures the appliance door to the cabinet hinge assembly, providing a stable pivot point for smooth opening and closing. Replaces a damaged or worn hinge base to restore proper door alignment and operation. What it does:

• Supports the door at the lower/upper hinge location so the door stays aligned and seals correctly
• Restores smooth door movement when a cracked or bent bracket causes sticking or binding
• Helps stop door sagging or uneven gaps that can let cold air escape
• Prevents metal-on-metal wear that can lead to noisy or unstable hinge operation

• One left-hand hinge base bracket

• Disconnect power (and water supply if appliance has a water line) before starting any repair
• Support the door securely before removing hinge fasteners to prevent injury or damage
• Use appropriate hand tools; avoid overtightening fasteners which can warp the bracket or hinge
• After installation, check door alignment and operation; adjust hinge position if needed for an even seal