Parts for Ge AJCH10DCBW1: 01 - Cabinet & Components Parts

Replacement drip pan for air conditioners. Installs beneath the evaporator coil to collect condensation. Needed when original pan is cracked or corroded.

Replace the special mounting nut for your room air conditioner. Secures components and panels. Order a new nut if the original is stripped or missing.

Replacement condenser shroud for air conditioners. Protects coils and directs airflow. Order a new shroud if yours is cracked, broken, or missing.

Secures and shields the condenser assembly in room air conditioners. Replace if your original plate is cracked, damaged, or missing to restore stability.

Replace a failing indoor fan motor causing weak airflow or no cooling. This motor typically takes 1-2 hours to install with basic hand tools.

Rubber cushion that mounts between the air conditioner motor and chassis to reduce vibration. Replace if cracked, hardened, or missing.

Replace a stripped, corroded, or missing special nut in your air conditioner. Secures internal components and panels for proper assembly and stability.

Weak airflow or no cooling from your air conditioner? This blower wheel circulates air over the evaporator coils. Moderate DIY repair in 30-45 minutes.

Replaces a cracked, worn, or damaged front panel bezel on your air conditioner. Restores appearance and provides secure mounting for controls.

Replacement horizontal louver for air conditioners. Directs airflow up and down. Needed when original louver is cracked, broken, or missing.

Replacement notch spring for air conditioners. Secures internal components. Order if original spring is broken, missing, or has lost tension.

This replacement brace is a structural support component that restores alignment and rigidity to the appliance cabinet or assembly, helping reduce vibration and prevent gaps or rubbing where panels meet. What it does:

• Reinforces the appliance frame to maintain proper alignment of panels and doors
• Helps stop vibrations, rattling, or shifting caused by a loose or broken support
• Restores correct spacing so adjacent parts can operate without rubbing or binding
• Used whenever a damaged brace causes wobble, misalignment, or visible gaps

• High-level replacement: remove access panels and fasteners to reach the damaged brace; replace with matching hardware
• Keep power disconnected and water supply turned off (when applicable) before starting repair
• Retain original screws/fasteners; verify fit and orientation before final tightening

Special mounting screw for air conditioner assembly. Replace if screw is stripped, missing, or damaged during maintenance or installation work.

Replace your air conditioner filter to maintain clean air circulation and efficient cooling. Change when dirty or damaged. Confirm fit with your model number.

This EVA pipe cushion is a foam sleeve that cushions and insulates a refrigerator's refrigerant tubing to reduce vibration and prevent metal-on-metal contact. It protects lines and helps cut down on noise and wear. What it does:

• Cushions refrigerant/evaporator tubing to stop rubbing and chafing
• Dampens vibration that can cause noise from the line set
• Provides basic insulation to reduce minor heat transfer at contact points
• Helps prevent damage from tube contact with cabinet or mounts

• One EVA foam pipe cushion

• Disconnect power to the appliance before servicing
• Slide or wrap the foam sleeve around the tubing at the contact point; trim to fit if needed
• Ensure the sleeve does not cover sensors, valves, or service access points
• Replace any damaged or brittle cushions to maintain protection

Louver base support plate for air conditioners. Mounts behind the directional louvers to provide structural support. Replace if cracked or broken.

Molded air vent louver grille for air conditioners. Restores proper airflow routing and finished appearance. Replaces cracked, broken, or missing vent.

Special screw for air conditioner assembly. Replaces lost, stripped, or damaged screws during installation or repair. Secures components properly.

Replace a cracked or broken cabinet support plate on your air conditioner. Mounts inside the unit to provide structural support for secure installation.

Replacement mounting bracket for air conditioner cabinets. Secures unit to window frame or wall. Order new bracket if original is bent, cracked, or missing.

Replace your air conditioner's front panel assembly if the original is cracked, broken, or damaged. This cosmetic panel covers the front of the unit.