Parts for Frigidaire FFTR1222QB0: 03 - Cabinet / Controls Parts

This plastic outer housing cover protects internal components and gives the appliance a finished appearance. It helps keep wiring and controls enclosed so the unit looks complete and safer to use. What it does

• Covers and protects internal components from dust, debris and incidental contact
• Restores the appliance's finished exterior where a broken or missing cover left an opening
• Helps prevent accidental contact with wiring or control parts behind the panel
• Visible damage or cracks can let in moisture or debris and warrant replacement

• One cover

• Disconnect power (unplug or shut off breaker) before removing or installing the cover
• Use appropriate hand tools to remove fasteners; keep track of screws and clips
• Handle the part gently to avoid cracking plastic or bending mounting tabs

This evaporator fan blade circulates cold air throughout the refrigerator compartment to keep temperatures even and food fresh. Replacing a damaged blade restores proper airflow and helps the cooling system run quietly and efficiently. What it does:

• Spins on the evaporator fan motor to move cold air through the freezer and fresh-food compartments.
• Restores airflow when a cracked or broken blade causes weak cooling or warm spots.
• Eliminates rubbing or wobbling noises caused by warped or chipped blades.
• Helps prevent uneven temperatures that can lead to frost buildup or spoiled food.

• Disconnect power to the appliance before servicing to avoid electric shock or moving parts.
• Remove the evaporator cover and inspect the motor shaft and mounting before installing the new blade.
• Slide the blade onto the motor shaft fully and verify it spins freely without contacting other components.
• If the fan motor is noisy or doesn't run, test and replace the motor as needed rather than only replacing the blade.

This control knob replaces a worn, cracked, or missing range/stove control knob so you can select heat settings and operate the cooktop or oven controls safely and easily. It provides a secure, push-on fit to the control shaft for reliable control. What it does:

• Rotates to select temperature or burner/preset settings on a range or stove control panel
• Snaps onto the control shaft and transmits user input to the underlying control
• Commonly used when the original knob is cracked, stripped, loose, or missing
• Restores a tactile grip and clear pointer for accurate setting selection

• Disconnect power to the appliance before starting any repair to avoid injury
• Installation is typically a simple push-on: align the knob's D-flat or keyed bore with the control shaft and press until seated
• If the knob is tight, use gentle, even pressure; do not force or pry with tools
• If the control shaft is damaged or the knob does not seat securely, inspect the shaft and control assembly and replace as needed

The Crisper Drawer is an OEM part for Frigidaire refrigerators. Designed to hold fruits and vegetables, this drawer optimizes the humidity levels to extend the freshness and lifespan of produce. It slides easily into its designated slot within the refrigerator, offering convenient storage and organization for your perishable items.

Causes of a bad crisper drawer can include overloading, which might lead to cracks or breaks; warping from the constant temperature changes inside the refrigerator; or the deterioration of the plastic material over time due to frequent cleaning agents or spills.

Symptoms of a bad crisper drawer include:

• Difficulty in sliding the drawer in or out
• Cracks or damage that can lead to leaks or decreased effectiveness in humidity control
• A loose fit within the refrigerator frame, which can affect its ability to maintain the proper humidity levels

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This control box is the appliance's main electrical control board that manages cycles, timers and powered components so the appliance runs correctly. Replacing a faulty control box restores reliable electronic control and response. What it does:

• Sends power and timed signals to motors, valves, heaters and displays
• Manages user commands and cycle sequencing for proper operation
• Prevents or causes symptoms when failing, such as no power, unresponsive controls, erratic cycles or failure to start
• Interfaces with connectors and sensors to coordinate appliance functions

• Disconnect power to the appliance before starting any service
• Handle the control box by its edges; avoid touching circuitry and use anti-static precautions if available
• Disconnect and note connector locations before removal to ensure correct reassembly
• After installation, restore power and run a short cycle to verify proper operation

This replacement mounting screw secures trim, panels, and components on compatible Frigidaire appliances to restore proper fit and stop loose parts from rattling or shifting. Use it to replace a missing or stripped fastener. What it does

• Fastens panels, brackets, or trim so components stay properly aligned
• Replaces missing or damaged screws that cause rattling or loose parts
• Helps restore secure door or control-panel attachment when a screw is lost
• Simple hardware replacement to avoid further wear from loose components

• Disconnect power and water to the appliance before starting any repair
• Use the correct screwdriver or driver bit to avoid stripping the head
• Thread the screw in by hand first, then tighten until snug—do not overtighten
• Inspect mating parts for repair or replacement

This push-button door switch completes the door circuit to turn the interior light on and signal door-open status. It replaces a failed switch to restore proper light and door-sensing function. What it does:

• Detects door open/closed position and makes/breaks the circuit for the interior light
• Restores interior lamp operation when the door is opened
• Commonly replaces switches that are stuck, intermittent, or fail to actuate
• Helps eliminate issues where the light stays on, never turns on, or flickers

• One door switch

• Disconnect power to the appliance before servicing to avoid shock or injury
• Access typically requires removing the door light lens or trim — keep trim and fasteners for reassembly
• Handle the switch and wiring gently; avoid pinching or straining the harness

This adjustable leveling foot replaces a worn or damaged refrigerator leg to restore stable, level operation and help doors close properly. It provides a simple height adjustment to reduce wobble and improve appliance performance. What it does:

• Replaces the lower support leg that bears the fridge weight and sets appliance height
• Lets you raise or lower the front (or rear, depending on model) for a level installation
• Helps stop rocking or vibration that can cause noise or uneven door alignment
• Can improve door sealing and reduce leaks caused by an out-of-level cabinet

• One leveling foot

• Disconnect power and empty the cabinet or move contents as needed for safe access
• Support the appliance before removing the old foot; use a jack or helper to prevent tipping
• Thread the new leveling foot in or out until the cabinet is stable and level; check with a bubble level
• Retighten any retaining hardware and restore power; adjust again after the appliance settles

This defrost thermostat with an integrated temperature fuse monitors evaporator temperature and helps control the defrost heater during defrost cycles to reduce frost buildup and protect the heater assembly from overheating. What it does:

• Senses evaporator temperature and permits the defrost heater to run only when needed
• Helps stop excessive frost buildup on evaporator coils and the freezer back wall
• Includes a thermal fuse for added over-temperature protection of the defrost system
• Commonly replaced when the freezer shows persistent ice buildup or defrost cycles fail to clear frost

• Always disconnect power to the appliance before servicing electrical components.
• Install the exact replacement part; do not bypass or defeat the thermal fuse—it's a safety device.
• Handle the thermostat and fuse carefully; avoid kinking or damaging sensor elements and mounting tabs.

This main electronic control board runs the appliance by processing keypad inputs and sensor feedback. Replacing a failed board can restore reliable operation when controls stop responding, settings won't take, or cycles behave erratically.

• Interprets keypad/display signals and sensor inputs to command system functions
• Controls compressor and fan operation based on selected mode and temperature
• Coordinates timing for cooling cycles and safety interlocks
• Common symptoms of a failed board: unresponsive controls, unit won't start, random shutoffs, error codes or flickering display

• Disconnect power before servicing; capacitors may retain a charge
• Use ESD protection and handle the board by the edges
• Photograph wiring and move connectors one at a time; transfer any jumpers/settings from the original, if present
• After installation, restore power and test all functions