Parts for Electrolux EFDE210TIS01: Cabinet / Drum Parts

This molded duct channels airflow inside the appliance to direct exhaust and ventilation where needed. Replacing a damaged duct restores proper air movement, helping the unit run more efficiently and quietly. What it does

• Routes air between internal components to enable proper ventilation and exhaust
• Helps prevent recirculation of hot air that can reduce performance
• Reduce unusual noises caused by cracked or loose ducts
• Common symptom: reduced airflow, longer cycle times, or overheating-related shutoffs

• Disconnect power (and gas if applicable) before beginning any repair
• Access may require removing exterior panels or housing
• Inspect mounting tabs and seals; replace fasteners or gaskets if damaged

This support mounting bracket secures internal components to the appliance chassis, restoring stable alignment and reducing vibration or rattling. Use it to replace a worn or broken bracket and help maintain proper part positioning. What it does:

• Holds and stabilizes internal assemblies or panels to the appliance frame
• Stops excessive movement that can cause rubbing, noise, or misalignment
• Restores mounting points needed for proper operation of connected parts
• Fits in locations where a small stamped/plastic bracket is required

• One support (mounting bracket) as shown

• Inspect surrounding fasteners and panels; replace any damaged screws or clips
• Use correct hardware and torque; avoid over-tightening which can crack bracket or panel
• Disconnect power before accessing internal areas; follow appliance-specific safety steps

This refrigerator door gasket creates an airtight seal around the door to help keep cold air in and maintain consistent temperatures. Replacing a worn or torn gasket restores proper sealing and improves cooling efficiency. What it does

• Seals the refrigerator/freezer door to prevent warm air infiltration and cold air loss
• Helps reduce frost buildup and keeps food fresher by maintaining stable temperatures
• Can reduce compressor run time and improve energy efficiency when sealing is restored
• Addresses common symptoms like warm spots in the compartment, visible gaps around the door edge, or excessive condensation/frost

• One door gasket

• Turn off power to the appliance before starting work and empty the door area for safe access
• Remove the old gasket per the manufacturer's instructions—some gaskets use screws/clips, others use a compression-fit
• Clean the gasket channel thoroughly and align the new gasket evenly; allow a gentle warm water or hair-dryer softening if the gasket is stiff
• If mounting hardware is damaged or the door is misaligned, replace hardware or correct alignment for a proper seal

This replacement water filter cartridge helps reduce common taste and odor issues in refrigerator water and ice for clearer, better-tasting water. Easy to swap when your fridge indicates a filter change. What it does:

• Removes or reduces chlorine taste and odor and other common impurities to improve water and ice flavor
• Helps protect dispenser and ice maker from sediment buildup
• Restores filtered water performance when your existing filter is expired or clogged
• Compatible with compatible-refrigerator filter housings that accept this cartridge style

• One replacement water filter cartridge

• Replace only with the exact recommended filter for your refrigerator model
• Flush several gallons of water through the new filter per manufacturer instructions before use
• Turn off the water supply and follow your refrigerator's filter removal procedure to avoid leaks
• Dispose of used filter per local regulations; do not attempt to disassemble the cartridge

This drive belt transfers motor power to the appliance's rotating components so the drum or agitator turns smoothly. Replacing a worn belt restores proper movement and reduces slipping or noise. What it does

• Wraps around the motor pulley and drum/agitator to transmit rotational force.
• Helps the drum or agitator rotate evenly for normal operation.
• Commonly linked to symptoms like a drum that won't spin, slipping or squealing noises, or burning rubber smells.
• Works as a maintenance replacement when the belt shows fraying, cracks, glazing, or loss of tension.

• One replacement drive belt.

• Disconnect power (and water if applicable) before beginning any repair.
• Follow the appliance's service manual for belt routing and tensioning; some models require removing panels or the drum/agitator assembly.
• Inspect idler pulleys, tensioners, rollers, and motor shaft for wear—replace any worn components to prevent premature belt failure.
• If you smell burning or see excessive damage, stop and verify correct part and fit before testing.

This replacement refrigerator door gasket creates an airtight seal around the door to help maintain proper temperatures and reduce energy loss. It restores a tight closing seal for better food preservation and fewer frost issues. What it does:

• Seals the refrigerator/freezer door to keep cold air in and warm air out
• Helps prevent moisture buildup and frost inside the compartment
• Reduces compressor run time by improving door sealing
• Restores proper door closure when the original gasket is cracked, torn, or warped

• One door gasket

• Replace gasket with the door open for easier access
• Clean the door flange and remove old adhesive/residue for a proper seal
• Re-seat the gasket around the full perimeter, checking for uniform contact and any trapped folds
• For safety, unplug the appliance or switch off power at the breaker before installing

This gasket creates a tight seal between two mating surfaces in your appliance to contain water or air and keep the system performing correctly. Replace a worn seal to stop leaks and restore reliable operation.

• Forms a secure seal between components
• Helps prevent water or air leaks at the joint
• Maintains proper pressure/airflow/temperature for the system
• Replaces gaskets that are cracked, flattened, torn, or deformed
• Address dripping, moisture accumulation, or air/steam escaping near the seal area

• Disconnect power; shut off water supply if applicable
• Note the gasket's orientation/routing before removal
• Clean and dry mating surfaces; remove old residue/adhesive
• Seat the gasket evenly and tighten fasteners uniformly; test for leaks before full reassembly

This cone is a molded mounting cone used to position and secure rotating components in select laundry appliances, helping restore proper alignment and reduce vibration for smoother operation. What it does:

• Centers and stabilizes an agitator or spin component to prevent wobble
• Provides a precise fit between mating parts for consistent rotation
• Helps reduce noise caused by misalignment or excessive movement
• Restores proper part engagement that can prevent rubbing or binding

• Inspect mating surfaces for wear or damage before installation
• Replace only with the correct OEM cone to ensure proper fit and function
• Disconnect power and follow the appliance manufacturer's safety instructions before servicing

This cone is a small OEM replacement part that helps position and support rotating components in the appliance for smooth operation and reduced wear. It restores proper alignment where the original cone is cracked or missing. What it does

• Centers and supports a rotating shaft or drum to maintain correct alignment
• Provides a low-friction contact surface between mating parts
• Helps prevent wobble, rubbing noises, and uneven rotation when functioning properly
• Used when the original cone is broken, cracked, or worn

• One cone

• Disconnect power before starting repairs to avoid shock or injury
• Remove access panels and any fasteners to reach the cone; keep track of hardware
• Inspect surrounding bearings, seals, and shafts for wear and replace if damaged
• Use appropriate hand tools; do not force parts—if fit is tight, verify orientation before applying pressure

This refrigerator water filter cartridge reduces common taste and odor issues and captures sediment for cleaner-tasting water and ice. Designed as a direct replacement cartridge for compatible Frigidaire refrigerators. What it does:

• Reduces chlorine taste and odor to improve drinking water flavor
• Helps trap sediment and particulates to clear cloudy water or ice
• Supports consistent water quality for ice makers and dispenser use
• Can improve dispenser flow when an old filter is clogged

• 1 refrigerator water filter cartridge

• Turn off the water supply and follow your refrigerator's manual for removal and replacement steps
• Flush several gallons of water through the dispenser after installation to clear air and initial carbon fines
• Replace according to manufacturer recommendations or sooner if you notice reduced flow or worsened taste
• Dispose of the used cartridge per local recycling or waste regulations

This is a replacement refrigerator door gasket that restores the door seal to help maintain even temperatures and keep food fresher. It's a direct-fit sealing strip used where a worn or torn gasket lets cold air escape. What it does

• Seals the refrigerator door edge to prevent cold air from leaking and reduce frost buildup.
• Helps maintain consistent internal temperature for better food preservation.
• Reduces compressor run-time caused by poor door sealing.
• Commonly replaced when the seal is cracked, torn, deformed, or no longer seals evenly.

• One refrigerator door gasket.

• Inspect the door frame and mounting channel for debris before installing; clean as needed.
• Most gaskets slide into a mounting channel and may require gentle warming or adjustment to seat evenly.
• Check door alignment and hinge condition if the gasket does not seal after installation.
• Disconnect power or follow appliance safety recommendations before performing repairs.

This is a replacement mounting bolt for appliance assemblies that secures panels, brackets, or components to the cabinet. Replaces a worn or missing fastener to restore proper fit and stability. What it does:

• Secures panels, brackets, or components in place to prevent rattling or misalignment
• Restores proper fastening where an original bolt is damaged, stripped, or missing
• Helps maintain appliance stability during normal use
• Compatible with the original mounting location and hardware when the OEM part number matches

• One replacement bolt

• Use the matching thread size and torque rating; do not overtighten to avoid stripping
• Replace only with the same style and length bolt for proper fit
• Disconnect power and water (if applicable) and follow appliance safety procedures before servicing

This bushing provides a low-friction bearing surface for a rotating shaft, helping stabilize movement and reduce wear on the surrounding housing. Replacing a worn bushing restores smoother operation and reduces noise from shaft movement. What it does

• Supports and centers a rotating shaft or shaft end within the appliance housing
• Reduces metal-on-metal contact to lower noise and wear
• Helps prevent shaft wobble that can cause vibration or uneven operation
• Commonly replaced when movement is loose or when you hear scraping/rubbing noises

• One bushing

• Disconnect power (and gas, if applicable) before starting any repair
• Access the part by removing the appropriate panels per your model's service instructions
• Remove the old bushing carefully to avoid damaging the shaft or housing; press or tap the new bushing into place squarely

Replacement roller that helps a dishwasher rack glide smoothly along its track, restoring proper rack alignment and quieter operation. Fits where a worn or damaged wheel causes the rack to stick, wobble, or derail. What it does:

• Replaces a worn or broken rack wheel so the rack rolls smoothly on its track.
• Stops rubbing, grinding noise, and uneven movement caused by a damaged roller.
• Prevents the rack from coming off the track or tilting when loaded.
• Helps restore proper rack alignment for easier loading and unloading.

• Disconnect power and water to the appliance before starting work.
• Inspect the rack track and mounting clip; replace clips or retainers if damaged.
• Typically installs with basic hand tools (screwdriver/pliers) — match orientation to the original wheel.
• Test rack travel after installation to ensure proper seating and smooth operation.