Parts for Electrolux EIED200QIS00: Cabinet / Drum Parts

Dryer cover panel that installs on the exterior cabinet. Replace if your original cover is cracked, damaged, or missing to restore appearance.

Leveling leg for dryers and laundry centers. Installs at the base corner to adjust height and stabilize the unit. Replace if cracked or missing.

This control panel is the appliance's user interface that houses the touchpads and display, letting you select cycles and view status. It restores responsive controls and visible status readouts when the original panel is cracked, faded, or nonfunctional. What it does:

• Provides the buttons/touchpads and display area for selecting settings and starting cycles
• Transmits user commands to the appliance's control board for operation
• Restores readable status indicators and backlight for clear feedback
• Common symptoms: unresponsive or intermittent buttons, missing display segments, cracked or damaged front surface

• 1 control panel (user interface) as shown

• Disconnect power (unplug or shut off breaker) before starting any work
• Handle glass and display areas carefully to avoid damage; wear gloves if needed
• Remove surrounding trim and fasteners to access the panel; keep hardware for reassembly
• If symptoms persist after replacement, test the control board and wiring harness for faults.

This control panel is the exterior console trim that houses the oven/range user controls and provides a finished look. It restores the appliance's interface area so buttons and displays sit securely and look factory-original. What it does:

• Replaces a cracked, faded, or damaged console panel to improve appearance and protect internal controls
• Provides the mounting surface for buttons, touch controls, and the control board
• Helps keep dust, moisture, and grease away from the underlying electronics
• Addresses common symptoms such as loose or broken trim, cosmetic damage, or exposed control openings

• Disconnect power to the appliance before starting any repair to avoid shock or injury
• Basic tools (screwdriver set) are typically required; remove trim pieces and any retainers to access mounting screws
• Handle with care to avoid scratching the finish or damaging clips during install
• If the panel attaches to electronic controls, support the control board and wiring;

This molded duct channels airflow inside the appliance to direct exhaust and ventilation where needed. Replacing a damaged duct restores proper air movement, helping the unit run more efficiently and quietly. What it does

• Routes air between internal components to enable proper ventilation and exhaust
• Helps prevent recirculation of hot air that can reduce performance
• Reduce unusual noises caused by cracked or loose ducts
• Common symptom: reduced airflow, longer cycle times, or overheating-related shutoffs

• Disconnect power (and gas if applicable) before beginning any repair
• Access may require removing exterior panels or housing
• Inspect mounting tabs and seals; replace fasteners or gaskets if damaged

Secures internal components to the dryer chassis. Replace this mounting bracket if cracked, broken, or worn to restore stable alignment and reduce rattling.

This is a flexible rubber gasket designed to create an airtight seal. It prevents air leaks that can reduce appliance efficiency and cause temperature regulation issues. Replace this gasket if you notice visible wear, cracking, or if the seal is no longer holding properly.

This is a mesh lint filter that fits inside the dryer's lint trap housing to capture lint and debris during drying cycles. It helps maintain proper airflow through the dryer drum for efficient drying and reduces fire risk. Replace this filter if it is torn, warped, has holes in the mesh, or if your dryer is taking longer than usual to dry clothes.

Dryer won't spin or makes squealing noises? This drive belt connects the motor to the drum. Common DIY repair that restores tumbling in 30-45 minutes.

Replace your dryer door seal gasket to prevent heat loss and improve drying efficiency. Worn gaskets cause longer cycles and higher energy costs. Verify fit with your model number before ordering.

Dryer front seal gasket creates a tight seal to prevent air leaks and ensure proper operation. Replace if worn, damaged, or causing noise issues.

Fix excessive vibration or wobbling during spin cycles. This mounting cone centers and stabilizes rotating components to restore smooth operation.

Replacement drum support cone for dryers. Centers and supports the rotating drum shaft for smooth operation. Needed when original cone is cracked or missing.

This is a mesh lint screen that fits into the dryer's lint trap housing, typically located inside the door opening or on top of the dryer. It captures lint and debris from clothing during the drying cycle to maintain proper airflow. Replace this screen if it is torn, warped, clogged beyond cleaning, or if your dryer is taking longer than normal to dry clothes.

Replace your dryer door gasket to restore the seal and prevent heat loss. Install when torn, cracked, or loose. Confirm fit with your model number.

Replacement mounting bolt that secures panels, brackets, or components to the dryer cabinet. Needed when original bolt is worn, missing, or stripped.

Dryer shaft support bushing provides a low-friction bearing surface for rotating shafts. Replace when you notice increased noise or rough rotation. Verify fit with your model number before ordering.

This is a single drum support roller that helps the dryer drum rotate smoothly during operation. The roller sits on a shaft at the rear or front of the drum and bears the weight of the drum as it spins. Replace this roller if the dryer makes a loud thumping, squealing, or rumbling noise during operation, or if the drum does not turn freely.

Dryer drum felt seal creates an airtight barrier between the drum and bulkhead. Replace if worn, torn, or causing squeaking noises. Verify fit with your model.