Parts for Ge DPGT750EC2WW: 02 - Cabinet, Front Panel & Door Parts

Safety cover cap for dryer installation. Replaces cracked, broken, or missing safety covers. Essential protective component for dryer housing assembly.

Wire harness that connects to the dryer's power control board. Replace if wires are frayed, connectors are damaged, or harness is melted or broken.

This is an internal communication cable that connects the dryer's control boards, allowing them to send and receive data signals. It ensures proper communication between the main control board and the user interface board. Replace this cable if the dryer displays error codes related to communication failures, the control panel becomes unresponsive, or the dryer stops mid-cycle unexpectedly.

This is an external serial communication cable used to connect a dryer's control board to diagnostic equipment or external communication modules. It allows data transfer between the dryer's electronics and service tools for troubleshooting. Replace this cable if the dryer cannot communicate with diagnostic systems, or if the cable is visibly damaged, frayed, or has corroded connectors.

Right-hand mounting bracket for dryers. Secures internal components in place. Replace if cracked, bent, or broken to restore proper support and alignment.

This cap drier plug seals the refrigerant drier opening on compatible GE refrigeration systems to help maintain a closed refrigerant circuit and prevent contaminant entry during service or assembly. It's a small service part that preserves system integrity. What it does:

• Seals the drier or access port to prevent refrigerant loss and moisture/contaminant ingress
• Helps protect the refrigeration circuit after drier or component replacement
• Used during service to close the system while lines are being connected
• Supports proper system operation by maintaining a sealed refrigerant path

• One cap drier plug (quantity: 1)

• Disconnect appliance power before servicing; follow manufacturer safety instructions
• Refrigerant handling and drier replacement require certified HVAC/R service technicians
• Inspect sealing surfaces and replace any damaged gaskets or fittings to ensure a leak-free seal
• Tighten per OEM guidance; do not overtighten or use damaged parts

Leveling leg for dryers. Installs at the base corner of the unit to support weight and adjust height. Replace if cracked, broken, or missing.

This is a replacement mounting screw used to secure appliance panels and components, restoring proper fit and reducing vibration or rattling. Use it to replace a missing or damaged fastener for a secure repair. What it does:

• Secures panels, trim, brackets, or small components in place
• Restores proper panel alignment and reduces rattling or vibration
• Replaces stripped, missing, or corroded screws that cause loose parts
• Helps maintain electrical and mechanical connections by holding parts steady

• Turn power off and unplug the appliance before beginning any repair
• Use the matching driver or bit to avoid stripping the screw head
• Replace only with the same type and size screw for a proper fit
• Inspect surrounding parts for wear

Complete dryer door assembly that replaces your damaged, cracked, or broken door unit. Installs on the front of your dryer for full access to the drum.

This is the complete dryer door assembly, including the door frame and inner panel. It serves as the main access point to the dryer drum, sealing the drum during operation to maintain proper airflow and heat. Replace this assembly if the door is cracked, warped, won't latch properly, or if the dryer stops mid-cycle due to a faulty door switch connection.

Fix a dryer door that won't stay closed or latch properly with this door latch body. Common repair for doors that pop open during cycles. Easy install.

Handle bracket for dryer doors. Secures the door handle assembly to the dryer panel. Replace if cracked, broken, or missing to restore proper handle mounting.

Metal bracket that secures the dryer motor to the base or frame. Replace if bracket is bent, cracked, or causing motor misalignment and vibration.

Fix a dryer that won't start or hums without turning with this micro switch. Common repair for door latch and control issues. Simple installation.

Dryer mounting screw secures panels, components, or brackets. Replace if stripped, missing, or damaged during disassembly. Essential hardware part.

Dryer drying rack installs inside the drum to provide a flat surface for air-drying delicate items. Replace if cracked, warped, or missing support bars.