Parts for Bosch HDI7282U/07: Cabinet Parts

This replacement fan restores proper airflow inside your appliance. It circulates air as designed by the manufacturer to help maintain stable temperatures, protect components, and support reliable operation.

• Moves air through the appliance or across components to aid cooling and ventilation
• Helps regulate temperature and prevent overheating of internal parts
• Symptoms of a failing fan can include weak or no airflow, unusual noises, overheating, or related error codes
• Restores the intended airflow path for consistent performance

• Disconnect electrical power before servicing; for gas appliances, also shut off gas if applicable
• Access the fan per your model's service information; note wiring, fasteners, and the fan's orientation
• Transfer any reusable brackets or hardware from the original part if needed
• After installation, verify the fan spins freely with no obstructions, then reassemble and test

This Terminal Box is an OEM part for Bosch Built-In Ovens. Integral to the oven's electrical system, this component serves as a secure connection point for various electrical wires within the appliance.

A common issue with a malfunctioning Terminal Box is loose connections or damage to the terminal block due to heat exposure or aging. 

Symptoms of a defective Terminal Box may include:

• Inconsistent power supply to the oven
• Non-functional heating elements
• Sparks or electrical arcing within the terminal box area

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.

A replacement pressure regulator that restores consistent pressure control for safe, reliable appliance operation. Helps stabilize fuel/air flow so burners and heating elements run at intended performance. What it does:

• Regulates pressure to maintain steady fuel or air flow to burners or valves
• Helps correct issues like weak or uneven heating, unstable flames, or intermittent operation
• Supports proper ignition and consistent temperature during normal use
• A faulty regulator can cause poor performance or safety concerns—address promptly

• Turn off power and shut off fuel (gas) supply before servicing; follow appliance safety guidelines
• Only install on compatible appliances; inspect the appliance manual
• Inspect fittings and seals for leaks after installation; perform a leak test if working with gas
• If you smell gas or suspect a leak, stop and immediately address the situation

The Foot is an OEM component specifically designed for Bosch freestanding and slide-in electric ranges. Constructed of rugged cast metal, anti-tip brackets stabilize cooking operation. Even weight distribution protects floors.

Causes of a broken foot commonly relate to impacts during moving or cleaning. Prolonged use weakens mounting clips requiring timely replacement. 

Symptoms of a bad foot include:

• Instability raising tip-over hazards
• Major leaning endangering cooktop surfaces    
• Loosening raising noise concerns

Causes of a bad foot can involve stress fractures from overloading or excessive slide-outs. Corrosion inhibits secure fastening necessitating replacment.

This OEM Bosch part is also compatible with some Thermador, Dacor, and Lynx ranges maintaining dependable positioning and anti-tilt protection over years of use. Replace for uninterrupted cooking confidence.
 

The Hinge is an OEM part for Bosch ranges. It is responsible for securely holding the oven door in place while allowing for easy opening and closing.  

Causes of a bad hinge can include wear and tear over time, damage due to repeated use or impact, or failure of internal mechanisms that assist in smooth movement.  

Symptoms of a bad hinge include:

• The oven door becoming loose or unstable
• Difficulty in fully opening or closing the door  
• Door alignment issues where the door does not sit flush
• Visible damage or cracks in the window or frame

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.

This hinge is the OEM replacement that supports and pivots your appliance door for proper alignment and smooth opening. Replacing a worn hinge restores correct door fit and helps prevent sagging or binding. What it does:

• Provides a pivot point for the appliance door to open and close smoothly
• Maintains door alignment and seal to help prevent leaks or uneven gaps
• Worn or damaged hinges can cause the door to sag, rub, or close unevenly
• Matches OEM fit and mounting points for direct replacement

• Disconnect power and water before inspecting or replacing door hardware
• Support the door during removal to prevent dropping or damage
• Compare new hinge to the old part for correct orientation and mounting before final installation
• Tighten fasteners securely but avoid over-torquing; test door operation after installation

This door hinge secures and lets the appliance door pivot smoothly, restoring proper alignment and seal for reliable operation. Use this hinge to replace a worn, bent, or broken door pivot that prevents the door from seating correctly. What it does:

• Provides a stable pivot point so the door opens and closes smoothly
• Restores correct door alignment to improve sealing and reduce air leaks
• Stops door sagging, binding, or uneven gaps when mounting hardware has failed
• Prevents rubbing or unusual noises from a loose or damaged hinge

• One door hinge

• Disconnect power to the appliance and remove contents from the door before servicing
• Support the door while removing and installing the hinge to avoid damage or injury
• Tighten fasteners securely to the manufacturer's torque recommendations; replace any worn screws