Parts for Bosch HGIP054UC/07: Cabinet Parts

Replaces cracked or damaged rear housing cover on your range. Protects internal components and ensures proper ventilation through integrated vents.

This Terminal Box is an OEM part for Bosch Built-In Ovens. Integral to the oven's electrical system, this component serves as a secure connection point for various electrical wires within the appliance.

A common issue with a malfunctioning Terminal Box is loose connections or damage to the terminal block due to heat exposure or aging. 

Symptoms of a defective Terminal Box may include:

• Inconsistent power supply to the oven
• Non-functional heating elements
• Sparks or electrical arcing within the terminal box area

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.

Range displaying error codes or controls not responding? This control module manages timers, temperature settings, and cooking functions. Moderate repair.

Uneven baking or slow cooking? This convection fan circulates heated air throughout your range oven for consistent, professional cooking results.

This replacement routing tube channels fluid inside the appliance to restore proper flow and stop leaks. It replaces a damaged, cracked, or clogged tube to help prevent water pooling and restore normal operation. What it does:

• Routes water or condensate between internal components to maintain proper drainage or flow
• Replaces cracked, split, or deteriorated tubing that can cause leaks or puddles
• Helps eliminate intermittent dripping or loss of water flow caused by blockages or holes
• Works as a direct-fit replacement when the original tubing has failed

• One replacement tube

• Disconnect power and shut off the water supply before installing
• Inspect and reuse or replace any retaining clips, clamps, or grommets as needed
• Slide tube fully into fittings and secure with appropriate clamps to prevent leaks

Replace your range's side panel if it's cracked, dented, or showing rust. This exterior panel covers the side of your appliance for a complete look.

Leveling foot for electric and gas ranges. Adjustable metal foot installs at base corner. Replace if cracked, broken, or missing to level your range.

Fix weak or uneven burner flames with this gas range pressure regulator. Controls gas flow for consistent cooking performance and safe operation.

This water inlet valve controls the flow of water into the appliance, restoring proper filling and preventing overfill when working correctly. Fits specific BOSCH machines and replaces a worn or failed inlet valve. What it does:

• Opens and closes to allow water into the appliance when a cycle calls for fill
• Helps maintain correct water level so cycles run and clean properly
• Failsafe against continuous fill when functioning correctly; common fault causes no-fill or constant-fill symptoms
• Often replaced when appliance leaks, won't fill, or runs continuously without stopping

• One water inlet valve

• Disconnect power and shut off water supply before attempting replacement
• Handle electrical connections and inlet lines carefully; inspect seals and hoses and replace if worn

Replace the side panel on your range. This exterior panel covers the side of the appliance. Order a new one if yours is dented, scratched, or damaged.

Mounting screw for wall ovens and ranges. Secures panels, brackets, or components inside the oven cavity. Replace if missing, stripped, or damaged.

This cable harness routes electrical signals between dishwasher components to restore proper control and power delivery. It replaces a damaged or broken wiring assembly so affected circuits can communicate and operate reliably. What it does:

• Connects control board, sensors, pumps and other internal components to carry power and signals
• Restores intermittent or lost power to specific assemblies caused by frayed or broken wires
• Helps eliminate error codes or failures tied to open or shorted harness connections
• Prevents arcing and poor connections that can cause unreliable operation

• One cable harness assembly as pictured

• Only install after disconnecting power to the appliance to avoid shock or damage
• Inspect mating connectors and pins for corrosion or damage before connecting
• Route harness away from sharp edges, moving parts and hot surfaces to avoid future wear

Fix intermittent power or electrical faults in your range with this cable harness. Routes power and signals between control and components. Direct fit.

Internal wiring cable for gas ranges. Connects electrical components inside your range. Replace if frayed, damaged, or broken to restore proper connections.

The Screw is an OEM part for Bosch microwave ovens. It is a component that secures the outer casing and front paneling of the microwave. The screw is designed to withstand repeated heating and cooling cycles without loosening or degrading. 

Symptoms of bad screw include:

- The front panel or outer casing becoming loose, detached, or misaligned
- Gaps appearing in the seams or joints of the microwave structure
- The door not sealing properly leading to leaks

Over many uses of the microwave, screws can wear down or strip out from over-tightening during repairs or installations. It is important to replace worn screws to ensure the microwave maintains an intact structure.

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.