Parts for Bosch WTC82100US/01: Cabinet Parts

Replace your dryer drum seal when you notice air leaks, excessive lint, or reduced drying efficiency. Verify compatibility with your model number.

The Heater Element is an OEM component specifically designed for Bosch dryers. It provides essential heating power to dry wet laundry efficiently. Precise temperature control during cycles relies on its ability to generate and regulate heat output.

Causes of a bad heater element can include cracks or breaks resulting from normal wear over extended use. Mineral buildup inside the element may also impact heat transfer over time.   

Symptoms of a bad heater element include: 

• Slow or inefficient drying times even on low-moisture cycles
• Lack of consistent temperature output during use  
• Safety sensors tripping the dryer or causing it to shut off unexpectedly

This OEM Bosch part is also compatible with some Thermador, Gaggenau, and Kenmore dryers. Replace yours today to restore optimized drying performance through reliable heat generation.
 

Dryer not heating properly or overheating? This temperature sensor monitors heat levels to ensure safe, effective drying. Moderate DIY repair.

Dryer not heating or overheating? The temperature limiter monitors heat levels and cuts power when limits are exceeded. Requires dryer disassembly.

This rear case is the outer shell that protects and supports the appliance's motor and internal components, restoring structural support and helping keep components aligned and shielded from debris. What it does:

• Covers and protects the motor, pumps and wiring at the rear of the appliance
• Helps maintain component alignment and mounting points for fasteners
• Reduces ingress of dust and debris that can affect moving parts
• Can stop vibration-related rubbing or contact caused by a damaged or cracked rear housing

• One rear case

• Disconnect power (unplug or shut off breaker) before starting any repair
• Remove adjacent panels and mounting screws to access the rear housing; retain fasteners for reuse
• Inspect mounting bosses, gaskets and internal components for damage while replacing the housing

Replace your dryer's duct if cracked, damaged, or missing. This duct channels air through the system for proper ventilation and efficient drying performance.

Dryer won't start or door won't stay closed? This door latch assembly secures the door during operation, allowing cycles to run. Moderate DIY repair.

This replacement seal restores a tight, leak-resistant connection between mating components inside your appliance. Replacing a worn seal helps stop drips at the joint and keeps the system operating reliably without nuisance leak faults.

• Forms a compressible barrier between parts to prevent leakage at a connection point
• Helps protect nearby components from moisture intrusion and corrosion
• Typical failure signs: moisture around a joint, puddling beneath the unit, or leak/overflow error messages
• Replace if the original is cracked, flattened, cut, brittle, or missing

• Disconnect power and shut off the water supply before servicing
• Access the connection, note the seal's orientation, and remove the old seal
• Clean mating surfaces; lightly moisten the new seal and seat it evenly without twisting or pinching
• Reassemble and test for leaks before reinstalling covers or panels

Temperature monitoring sensor located in the dryer's heating system that regulates drying temperatures. Replace if clothes aren't drying properly, take too long to dry, or if the dryer overheats.

Captures lint and debris from dryer exhaust to maintain airflow and drying performance. Replace when damaged or clogged. Verify fit with your model.

Dryer cover restores a secure closure over openings, protecting internal components. Replace when cracked, broken, or missing to maintain fit and appearance.

Replace your dryer's rubber door seal to prevent air leaks and maintain efficient drying. Install when seal shows cracks, tears, or no longer seals properly.

This is the lower front cover panel, commonly called a toe panel, that attaches to the bottom of the dryer's front face. It conceals internal components and provides a finished appearance to the front of the unit. Replace this panel if it is cracked, warped, missing, or damaged, which can expose internal parts and affect the dryer's appearance.

This is a drum support roller that sits on an axle and helps the dryer drum rotate smoothly during operation. The roller bears the weight of the drum and its contents, reducing friction and noise. Replace this part if you hear thumping, squealing, or rumbling noises while the dryer is running, or if the drum no longer spins freely.

Fix a dryer that won't start due to a faulty door lock. This mechanical lock assembly ensures your dryer door latches securely for safe operation.

Dryer won't start or shows error codes? A faulty cable harness disrupts electrical connections. This internal wiring assembly restores communication.