Parts for Crosley CF057: Cabinet Parts

This hinge-side door stop helps limit door travel and protect the hinge assembly from over-rotation for a secure, consistent door movement. Replaces a worn or broken hinge-side stopper to restore proper door alignment and operation. What it does:

• Acts as the stop/breaker on the hinge side to prevent the door from swinging past its intended range
• Helps reduce stress and wear on the hinge and door seal caused by over-rotation
• Commonly replaced when the door catches, over-rotates, or the hinge feels loose
• Works with the hinge assembly to keep door movement smooth and predictable

• Disconnect power to the appliance before starting any repair
• Remove the door or access hinge per your model's service instructions to reach the stopper
• Inspect adjacent hinge hardware and fasteners; replace any stripped or damaged parts
• Use proper hand tools and follow manufacturer torque and alignment guidance

This temperature control knob replaces a worn or missing knob so you can easily adjust the cold-control setting. Restores smooth, precise temperature adjustments and a clean, factory look. What it does:

• Attaches to the cold-control (thermostat) shaft to change the temperature setting
• Provides secure grip and pointer alignment for accurate selections
• Typical failure symptoms: cracked or missing knob, stripped hub, or a knob that slips or won't turn the control

• 1 temperature control knob

• Disconnect power before servicing
• Pull the old knob straight off the shaft; avoid prying at an angle to prevent shaft damage
• Align the shaft shape with the new knob and press firmly until fully seated
• The pointer aligns with the control graphics after installation

A replacement temperature control (thermostat) that regulates the refrigerator/freezer cooling cycle so food stays at the set temperature. Restores reliable on/off cycling when the original control fails. What it does

• Sends the signal to the compressor and fans to maintain the selected interior temperature.
• Replaces a faulty control when the appliance is too warm or too cold, or when temperatures fluctuate.
• Can stop short-cycling or continuous-run issues caused by a defective control.
• Works with the fridge's user temperature selector to restore normal cooling responses.

• Disconnect power to the appliance before starting any repair to avoid shock or injury.
• Handle control and wiring harness carefully; note or label wire locations before removal.
• Mount the control in the original position and reconnect wires to the matching terminals.

This hex head screw secures panels, brackets, and small components on appliances, restoring proper fit and stability. It's a direct replacement fastener when an original mounting screw is missing, loose, or damaged. What it does:

• Secures panels, brackets, trim, and internal components to prevent rattling or movement
• Replaces stripped, missing, or damaged mounting screws that cause loose parts or misalignment
• Restores reliable mechanical fastening so doors and panels sit flush and operate correctly
• Works as a general-purpose appliance mounting screw when original fasteners are worn

• Always disconnect power to the appliance before starting any repair
• Match the screw to the original location and thread engagement; start by hand to avoid cross-threading
• Use the correct driver or socket for the hex head and tighten until snug—do not overtighten
• If the original hole or threads are damaged, repair or replace the mating hardware before installing the screw

This refrigerator thermometer monitors interior temperature to help you keep food at safe storage conditions. It's a simple, direct replacement that restores visible temperature info so you can verify cold zones. What it does

• Displays the current refrigerator compartment temperature so you can check cooling performance at a glance
• Helps identify inaccurate or fluctuating temperatures that can cause food spoilage
• Works as a visual reference when troubleshooting cooling or thermostat issues
• Suitable for replacing a cracked, unreadable, or missing temperature gauge

• Disconnect power or unplug the appliance before attempting any repair
• Remove the old thermometer by gently releasing its mounting tabs or clips; avoid forcing nearby shelves or liners
• Snap or press the replacement thermometer into the same bracket or mounting location until secure

Color: White

The Frigidaire Touch-Up Paint is white in color in a .6 fl oz bottle. For almond order 5303321320. For black order 5303321321.

The Touch Up Paint is an OEM part for Frigidaire appliances. Whether you're dealing with scratches, chips, or other minor cosmetic damage, this touch-up paint provides an easy and effective solution for maintaining the appearance of your appliance. It's designed to adhere well to metal surfaces, offering durability and resistance to further wear and tear.

Over time, appliances can accumulate minor surface damage from regular use, cleaning, and accidental impacts. Using the Touch Up Paint not only improves the aesthetic appeal of your appliance but also helps protect exposed areas from rust and corrosion, which can extend the life of the appliance.

Symptoms of needing Touch Up Paint include:

• Visible scratches or chips on the appliance's surface.
• Areas of rust or corrosion that need to be covered after treating the rust.
• The desire to maintain or improve the appliance's appearance for aesthetic reasons or to maintain its value.