Parts for Crosley CFC162RCA: Cabinet Parts

This name plate is the replacement cabinet label that identifies your appliance's model, serial and manufacturing information. It restores a readable identification label so owners can service and parts details. What it does:

• Replaces a missing, damaged or illegible appliance identification label
• Provides model/serial and manufacturing markings needed for service and parts lookup
• Supports resale or warranty verification when factory labeling is required

• One name plate

• Verify exact label location before removal; labels are often secured with adhesive or small fasteners depending on model
• Clean and dry the mounting area for best adhesion or prepare fastener holes as needed
• Use care when removing old label to avoid surface damage; a heat gun can soften adhesive if present
• Disconnect power before working in tight appliance areas and follow all safety precautions

The Temperature Control Thermostat is an OEM part for Frigidaire freezers. It is an electro-mechanical component that precisely regulates internal temperatures according to user settings on the digital display. The thermostat monitors and reacts to changing conditions by signaling the cooling system to engage or deactivate.

Causes of a bad thermostat can include failures of temperature sensing components over several heating/cooling cycles. Excess moisture exposure or damage from foreign material inside the unit may also compromise function. 

Symptoms of a bad thermostat include:  

• Inability to select temperature settings or maintain consistent cooling
• Food not chilling as expected 
• Refrigerator Run light staying on for extended periods
• Unusual odors coming from inside the refrigerator compartment

This OEM Frigidaire replacement thermostat is compatible with Electrolux, Gibson, Kelvinator, and Kenmore models. 
 

This genuine appliance screw secures panels and components to keep your refrigerator parts aligned and stable. A small but essential fastener, it restores proper fit and stops rattling or loose trim for reliable operation. What it does:

• Fastens panels, trim, or internal components to the appliance frame
• Restores secure fit when factory screws are missing or stripped
• Stops vibration- or temperature-related rattling caused by loose hardware
• Helps maintain proper spacing and alignment of serviceable parts

• Turn off and unplug the appliance before servicing electrical or internal areas
• Use the matching screw hole and thread engagement; start by hand to avoid cross-threading
• Tighten until snug—do not overtighten to prevent stripping or cracking surrounding material

This full-width upper storage basket sits at the top of the freezer compartment. It hangs on the upper rails to keep smaller items organized and easy to reach, restoring usable space when the original basket is damaged or missing.

• Provides full-width storage at the top of the freezer for frequently used items
• Hangs from the upper rails for quick access and improved organization
• Replace if the original basket is bent, broken, rusted, or the coating is flaking
• Helps prevent small packages from falling to the bottom of the compartment

• Always disconnect power before servicing
• Open the door/lid, lift out the old basket, and set the new basket onto the upper rails
• Ensure both hooks are fully seated on the rails and the door/lid closes without interference
• No tools typically required

This panel-mounted signal light is the small indicator lamp that illuminates when a function is active. It restores clear visual status on the control panel so you can tell at a glance when the appliance is operating. What it does:

• Lights to indicate when a feature, cycle, or function is on (model-dependent)
• Restores visible status feedback on the console or control panel
• Helps alert you if a function remains active after use
• Addresses issues such as no light, constant-on light, flickering, or a damaged lens

• 1 signal light

• Disconnect power at the breaker before servicing
• Access the control panel/console; remove knobs and screws as needed
• Note wire positions or take a photo; transfer wires to the new light
• Secure the light in the panel, reassemble, restore power, and test

This adhesive-backed plastic mounting clip secures wires, small hoses, or components inside appliances to reduce movement and rattling. Its low-profile design helps keep internal parts organized for quieter, safer operation. What it does:

• Holds wiring harnesses, sensor leads, or small tubing in place to prevent chafing and noise
• Reduces vibration-related contact that can cause intermittent electrical or sensor issues
• Provides a simple, non-invasive mounting point without drilling or fasteners
• Adhesive backing allows quick placement in tight or hard-to-reach areas

• Clean and dry mounting surface; remove backing and press clip firmly for full adhesion
• Allow adhesive to set per ambient temperature (avoid stress on clip during initial cure)
• Disconnect power before installing
• Replace any brittle or damaged surrounding insulation or wire loom as needed

This replacement screw secures appliance components so brackets, shelves, trim, or panels stay firmly in place. Install a new screw when the original is missing, stripped, or corroded to restore a tight, rattle-free fit.

• Fastens brackets, panels, trim, or covers to the cabinet or liner
• Helps maintain alignment and reduce vibration and noise
• Direct replacement for a missing, rusted, or stripped fastener
• Use wherever your model's parts diagram specifies this screw

• Disconnect power before servicing; shut off water if working near water lines
• Match thread and length to the original location as shown in your model's parts diagram
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening (especially into plastic)
• Retain and transfer any original spacers or clips used with this fastener