Parts for Electrolux E23CS78HPS5: 07 - Cabinet Parts

Frigidaire PureAir® Refrigerator Air Filter combines activated carbon, Zeolite and real baking soda to reduce odors from foods such as onions, garlic, fish, stale milk and over-ripe fruits and vegetables. Recommended air filter replacement is every six months. Dimensions: 4-1/2" x 2-1/2"

The Door Light Switch is an OEM part for Frigidaire refrigerators. It is a component located inside the refrigerator door that turns the interior light on and off based on door position. The light switch works with a door switch plate and light socket assembly to automatically illuminate the interior when the door is opened.

Causes of a bad switch can be normal wear and tear over time, especially from frequent door openings. The contact points within the switch can become corroded or damaged.

Symptoms of a bad light switch include:

• Interior light not turning on at all when door is opened
• Light remaining constantly on even when door is closed
• Inconsistent or intermittent lighting

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.
 

The Screw is an OEM replacement part for Frigidaire refrigerators. This small but essential component is used to secure various parts of the appliance, such as panels, brackets, or internal fixtures, ensuring the refrigerator's structural integrity and proper operation.

Over time, screws may become loose, stripped, or corroded due to regular use, environmental factors, or maintenance work. A damaged or missing screw can lead to misaligned parts or reduced stability of the appliance.

Symptoms of a bad or missing screw include:

• Loose or wobbly components within the refrigerator
• Panels or fixtures coming apart or misaligned
• Difficulty securing parts during maintenance or repair
• Rattling or unusual noises during operation

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This door closer plate is a hinge component that helps your refrigerator door swing closed and seal properly. Replacing a worn plate restores smooth door action and supports a reliable seal to help maintain interior temperatures.

• Guides the hinge/cam for self-closing action and a consistent door stop
• Helps the door close fully and stay shut to protect the gasket seal
• Common symptoms include clicking/grinding at the hinge, door drifting open, or misalignment
• A weak seal from incomplete closing can contribute to frost or condensation

• Unplug the refrigerator; turn off the water supply
• Remove items from the door and support the door to prevent strain on the hinge
• Remove hinge cover and fasteners, separate the hinge as directed by your manual, and replace the closer plate; align with the mating cam
• Reassemble, level/align the door, and verify smooth closing and gasket contact

This turntable roller assembly sits under the glass tray to support and guide it as it rotates. Replacing a worn or damaged ring helps restore smooth tray movement for more even heating and dependable microwave performance.

• Supports the glass tray and allows smooth, consistent rotation
• Helps prevent tray wobble, binding, or scraping noises
• Can address issues like the tray not turning or uneven cooking
• Replaces cracked, warped, or missing roller rings

• Disconnect power before servicing
• Remove the glass tray, lift out the old ring, and clean the cavity floor
• Place the new ring wheels-down, seat the tray on the coupler, and test rotation
• Do not operate the microwave without the roller ring and tray properly installed

This lower hinge bracket mounts at the bottom of the cabinet to support and align the refrigerator door. Replacing a bent or worn bracket helps restore smooth door operation and a consistent gasket seal to help reduce air leaks.

• Provides the mounting base for the lower hinge/pin at the bottom of the cabinet
• Supports the door's weight to keep it level and properly aligned
• Helps the door open and close smoothly without scraping or binding
• Typical symptoms: door sagging or misalignment, difficulty closing, gaps at the gasket, squeaks/scraping near the lower hinge, or visible bracket damage

• Disconnect power; remove items from the door and support the door to prevent dropping
• Mark hinge/bracket locations for alignment; remove bottom hinge cover and mounting screws
• Transfer hinge pin and any spacers from the old bracket if applicable; install the new bracket and tighten screws securely
• Rehang and align the door; confirm full gasket contact and smooth door swing

This lower hinge bracket supports and aligns the refrigerator door at the bottom pivot point. Replacing a bent or worn bracket restores smooth door movement and proper alignment so the door opens and closes without rubbing or sagging.

• Provides the mounting point for the lower hinge/pin at the cabinet base
• Keeps the door square and aligned for smooth opening and closing
• Common fix for door sagging/drooping or rubbing at the bottom corner
• Helps eliminate scraping, binding, or squeaking from a damaged hinge area
• Replaces cracked, bent, or stripped brackets

• Disconnect power and remove items from the door to reduce weight.
• Support the door; remove the bottom hinge cover and screws, then lift the door off the lower hinge pin.
• Remove the old bracket, transfer any reusable hardware/shims, and install the new bracket securely.
• Reinstall the door, check gaps and gasket contact, adjust as needed, and restore power.

Used on fresh food and freezer doors.

This upper hinge cover is the plastic trim piece that snaps over the refrigerator's top door hinge to protect the hinge and restore a finished appearance. It hides hardware and helps keep the hinge area clean. What it does:

• Covers and protects the upper door hinge from dust, spills, and accidental contact
• Restores the refrigerator's finished look when the original cover is cracked or missing
• Helps prevent debris from accumulating around hinge hardware
• Supports safe operation by keeping moving parts shielded

• High-level task: usually snaps into place or attaches with the existing hinge screws; some models require loosening the hinge to fit the cover
• No electrical disconnect is typically required, but unplug the appliance or turn off power for safety when working near electrical components
• Keep original screws and hardware; re-use existing hinge fasteners unless replacements are supplied
• If hinge alignment is affected, re-tighten hinge hardware and check door operation after installation

Specs: 1.40`` long

Specs: Hex head ,1/4-20 x 5/8

This turntable roller assembly sits under the glass tray to support and guide it as it rotates. Replacing a worn or damaged ring helps restore smooth tray movement for more even heating and dependable microwave performance.

• Supports the glass tray and allows smooth, consistent rotation
• Helps prevent tray wobble, binding, or scraping noises
• Can address issues like the tray not turning or uneven cooking
• Replaces cracked, warped, or missing roller rings

• Disconnect power before servicing
• Remove the glass tray, lift out the old ring, and clean the cavity floor
• Place the new ring wheels-down, seat the tray on the coupler, and test rotation
• Do not operate the microwave without the roller ring and tray properly installed

This replacement screw fastens appliance components such as panels, brackets, and covers. Installing a new fastener restores a snug, rattle-free fit when the original screw is missing, stripped, or corroded.

• Secures covers, brackets, or trim to the cabinet or liner
• Replaces missing, stripped, or rusted hardware
• Helps reduce vibration and rattling from loose parts
• Supports proper alignment and stability of assemblies

• Disconnect power before servicing the appliance
• Use the correct driver/bit and start threads by hand to avoid cross-threading
• Do not overtighten, especially into plastic or thin sheet metal
• Retain and reinstall any original washers or spacers, if present

This genuine replacement screw secures appliance components and panels so parts stay properly aligned and rattle-free. Use it to replace a missing, stripped, or corroded fastener and restore a snug, reliable fit.

• Fastens brackets, covers, panels, and other hardware in their original locations
• Helps resolve loose or vibrating components and rattling noises
• Replaces missing or damaged hardware that can cause gaps or misalignment
• May be used in multiple locations

• Disconnect power; shut off water supply if working near water lines
• Compare to the original screw and install in the same location/orientation
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Refer to your model's exploded view to verify quantity and placement

This replacement mounting screw secures appliance components and restores proper fit where original fasteners have stripped, corroded, or been lost. It's a simple, low-cost fix to keep panels, brackets, and small assemblies held in place. What it does:

• Fastens panels, brackets, trim, or small assemblies to the appliance frame
• Restores secure attachment when original screw is missing or damaged
• Prevents vibration-related noise from loose components
• Helps maintain safe, correct alignment of connected parts

• Use the matching driver and correct size to avoid stripping the head
• Hand-start the screw to ensure proper thread alignment before tightening
• Do not overtighten; stop when snug to avoid damaging threads or plastic parts
• Disconnect power and follow all safety guidelines for your appliance before servicing

This factory fastener secures appliance panels and components. Replace a missing, stripped, or corroded screw to restore a tight, rattle-free fit and keep brackets and covers properly aligned.

• Fastens panels, brackets, and internal parts as specified by the manufacturer
• Helps maintain alignment and reduces vibration/rattling
• Replace if the head is stripped, threads are damaged, or corrosion is present
• Symptoms include loose/missing hardware, gaps, or rattling during operation

• Disconnect power; shut off gas/water if applicable before servicing
• Use the correct driver/bit size to avoid stripping the head
• Start threads by hand to prevent cross-threading; do not overtighten
• Match screw length/thread to the location; replace in sets when required

This replacement rear compressor base roller supports the refrigerator compressor on the cabinet rear base, helping keep the compressor properly seated and reducing wear from vibration and movement. What it does

• Provides a rolling support under the compressor to keep it aligned and off the cabinet floor
• Helps reduce vibration and rattling that can occur from a loose or worn compressor mount
• Prevents compressor body from dragging or scraping the cabinet base
• Commonly replaced when the roller is cracked, worn flat, missing, or causing noise

• Disconnect power to the appliance before starting any work
• Support or secure the compressor and cabinet before removing the old roller to avoid sudden movement
• Basic hand tools usually required; inspect mounting hardware and replace any damaged fasteners
• Do not attempt sealed-system repairs.

This rivet is a metal fastener used to permanently secure panels, brackets, or internal components in your appliance. Replacing a damaged or missing rivet restores a tight fit and helps prevent vibration, rattles, and looseness.

• Permanently joins thin metal parts where screws or nuts aren't used
• Maintains alignment and structural integrity of housings and frames
• Helpful when panels or components are loose, rattling, or won't stay secured
• Direct replacement for a worn, broken, corroded, or drilled-out factory rivet

• Disconnect power and shut off gas/water (as applicable) before servicing
• Support the part being fastened; drill out the old rivet head if needed
• A hand riveter/rivet tool may be required to set the new rivet
• Wear eye and hand protection during drilling/riveting

This cover assembly replaces a damaged or missing cover on your appliance, protecting internal components and restoring a clean, finished appearance. Use it when the original is cracked, loose, or no longer secures properly.

• Shields internal parts from debris, spills, and accidental contact
• Helps keep components enclosed and aligned for reliable operation
• Restores the appliance's finished look after damage or wear
• Common signs of failure: cracks, broken or missing tabs, discoloration, rattling, or a cover that won't stay in place

• Disconnect power before servicing; shut off water supply if working near water connections
• Remove retaining screws or release tabs; note the orientation of the original cover
• Transfer and reuse original screws, clips, or seals if required
• Do not overtighten fasteners into plastic; ensure all tabs fully engage before testing

This coil cover seal is a molded gasket that fits around the evaporator/coil cover to help keep airflow directed and reduce moisture and frost buildup. It restores the cover's sealing surface for more consistent cooling performance. What it does:

• Seals the evaporator/coil cover to help maintain proper airflow through the coil
• Helps reduce frost or ice buildup by keeping moist air away from cold coil surfaces
• Can prevent water dripping or pooling inside the cabinet near the coil
• Restores a tighter seal after a cracked, torn, or compressed gasket reduces effectiveness

• Disconnect power to the appliance before starting any repair
• You may need to remove the evaporator/coil cover or access panel to reach the seal
• Clean the mating surfaces and dry thoroughly before installing the new seal
• Handle the gasket gently and press evenly to seat; avoid stretching or sharp tools that could damage the part

This replacement screw secures refrigerator components such as brackets, trims, and covers. Replace missing or stripped hardware to keep parts tight and aligned, helping eliminate rattles and restoring a solid, reliable fit.

• Fastens interior or exterior components to the cabinet or doors
• Replaces missing, rusty, or stripped hardware
• Helps reduce vibration noises from loose parts
• Restores proper fit and alignment of panels, trims, or covers

• Disconnect power; turn off water supply if working near the dispenser or ice system
• Retain and reuse any original spacers or washers
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Replace one fastener at a time to maintain alignment

The Rear Crisper Cover Support is an OEM part for Frigidaire refrigerators. It plays a key role in supporting the crisper cover, which is the shelf that holds the crisper drawers. This part ensures that the cover remains stable and level, providing reliable support for storing fresh produce and other items in the crisper drawers.

Symptoms of a bad Rear Crisper Cover Support include:

• The crisper cover sagging or failing to stay in place
• Difficulty sliding the crisper drawers in and out
• Noticeable instability or wobbling of the cover
• Cracks or breakage where the support attaches to the refrigerator wall

Causes of a bad Rear Crisper Cover Support can involve regular wear and tear, excessive weight placed on the crisper cover, or accidental damage during cleaning or handling.

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Front Crisper Cover Support is an OEM replacement part for Frigidaire refrigerators. It is a component that provides structural integrity and support for the crisper cover or glass shelf located in the refrigerator's crisper drawers.

Symptoms of a faulty Front Crisper Cover Support include:

• Sagging or misaligned crisper cover or glass shelf
• Difficulty in opening or closing the crisper drawers
• Visible cracks, breaks, or damage to the support itself

Causes of a bad front crisper cover support can include normal wear and tear, physical impact or mishandling, or exposure to excessive moisture or temperature fluctuations.

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore refrigerator models.

Specs: .875`` long