Parts for Frigidaire GRQC2255AF0: Cabinet Parts

This replacement screw secures appliance panels, brackets, and components for a solid, rattle-free fit. Replace stripped, rusted, or missing hardware to restore proper alignment and dependable fastening where this fastener is specified.

• Fastens panels, brackets, trim, or internal parts to the cabinet/frame
• Helps maintain alignment and reduce vibration or rattling noises
• Direct replacement for stripped, rusted, or missing hardware
• Symptoms include loose panels, gaps, or screws that won't tighten

• Disconnect power (and gas/water if applicable) before servicing
• Use the correct driver/bit; hand-start threads to avoid cross-threading
• Replace screws one at a time to maintain alignment
• Snug firmly—do not overtighten into plastic or thin metal

This door hinge restores smooth, supported pivoting for a refrigerator or freezer door so it opens and closes correctly. Replace a worn or damaged hinge to stop binding, sagging, or uneven door alignment. What it does

• Provides the pivot point that supports and guides the appliance door as it opens and closes
• Stops door sag, misalignment, and rubbing caused by a worn or bent hinge
• Reduces binding or noisy movement at the door edge
• Helps ensure the door seals properly by maintaining correct alignment

• Disconnect power and remove stored items from the door before starting
• Support the door while removing and installing the hinge to prevent dropping or damage
• Use the original mounting screws or hardware and tighten securely; check door alignment after installation
• If hinge is bent or mounting holes are damaged, inspect surrounding parts for wear and replace as needed

This support is a replacement mounting/stabilizer bracket that helps secure the appliance cabinet components and keeps moving parts aligned for reliable operation. Use it to restore proper fit and reduce wobble or misalignment. What it does:

• Provides a stable mounting point for cabinet panels or internal assemblies
• Helps maintain proper alignment of moving parts to prevent rubbing or uneven wear
• Reduces cabinet movement that can cause noise or poor sealing
• Commonly replaced when broken, cracked, or bent from impact or wear

• One support bracket as shown

• High-level replacement: remove power and follow appliance disassembly to access the damaged support
• Handle panels carefully to avoid damage; keep fasteners organized for reassembly
• Inspect adjacent clips, screws, and mounting features and replace if worn or damaged

This support is a small mounting bracket that helps secure internal panels and components so they stay aligned and stable. Replacing a worn or broken support restores proper fit, reduces noise, and prevents further cabinet damage. What it does

• Secures and aligns internal panels or components to maintain proper positioning
• Dampens vibration and prevents rattling or movement during operation
• Keeps adjacent parts from rubbing or wearing unevenly
• Helps maintain correct door/panel fit and overall cabinet stability

• One support (mounting bracket)

• Disconnect power before beginning any repair to avoid shock or injury
• Use basic hand tools; handle edges carefully—panels may be sharp
• Confirm correct orientation and fastener locations before tightening

This is a replacement mounting screw used to secure appliance panels and small components so parts stay firmly in place during normal use. Installing the correct screw restores proper fit and reduces rattles or loose trim. What it does:

• Fastens panels, brackets, or trim to the appliance frame
• Keeps components aligned to prevent vibration and noise
• Replaces a lost or stripped screw to restore secure attachment
• Helps maintain safe, stable operation by holding parts where they belong

• One replacement mounting screw

• Disconnect power and water before servicing
• Use the correct screwdriver or bit to avoid stripping the head
• Tighten until snug; avoid over-tightening which can damage threads or panels
• Keep removed fasteners organized so you reinstall them in the original locations

This replacement screw secures appliance panels and components so parts stay aligned and stable during normal use. It's a direct-fit fastener commonly used in range, oven, and other household appliance assemblies. What it does

• Holds trim, panels, brackets, or small components in place to prevent rattling or misalignment
• Restores secure mounting when an original screw is missing, stripped, or damaged
• Helps eliminate vibration-related noise from loose parts
• Suitable where the original manufacturer specified this screw for mounting tasks

• One replacement screw

• Use the correct driver size and turn carefully to avoid stripping the head or threads
• Do not overtighten; stop when snug to prevent cracking panels or stripping threads
• Disconnect power to the appliance before accessing internal components or panels
• Replace only like-for-like fasteners; if thread size or head type is uncertain, verify against the original part

The Door Switch is an OEM part for Frigidaire refrigerators. It is a basic on/off switch located inside the refrigerator door frame that controls power to interior lights. 

When the door is opened, the magnet inside activates the switch, illuminating LED lights inside the refrigerator and freezer compartments for convenience. This allows for ease of accessing and identifying items without additional switches.

Causes of a bad door switch can include normal wear over time, moisture exposure, or impact damage.

Symptoms of a bad door switch include:

• Lights not turning on when the door is opened
• Lights remaining on continuously even when the door closed  
• Inability to shut off lights manually 

Replacing the switch with a Frigidaire OEM part ensures the refrigerator's interior lights function properly based on the door position. It also helps optimize energy usage. This replacement is compatible with models by Electrolux, Gibson, Kelvinator, and Kenmore.

This harness with reed switch detects a magnetic field and provides a ready-made wiring connection for the appliance's door/sensor circuit, restoring reliable sensing and signal routing. What it does

• Contains a reed (magnetic) switch in-line with a multi-conductor harness to detect open/closed or presence/absence of a magnetic field
• Replaces a damaged or faulty sensor harness that can cause intermittent or no signal to the control board
• Common symptoms: appliance not sensing door/cover, controls not responding, or features tied to the sensor fail to activate
• Designed to mate with the factory connector set and routing used by the original equipment

• One complete harness with reed switch

• Verify power is disconnected before accessing wiring or replacing the harness
• Handle the reed switch and connectors gently to avoid damage; secure harness with original clips or fasteners

This interior refrigerator lamp provides replacement lighting for the fresh-food compartment so you can see contents clearly and check temperature/food without fumbling in the dark. What it does:

• Replaces a burned-out or flickering interior fridge light so the compartment is illuminated
• Helps you quickly find items and inspect food condition without opening the door longer than necessary
• Restores normal operation when the light does not turn on or is dim
• Fits into the fridge's interior lamp socket and functions with the existing switch assembly

• Disconnect power to the appliance before replacing the lamp to avoid shock
• Allow the old bulb to cool before removing; use a cloth or gloves to handle the new bulb
• Install only the correct lamp type for your model; do not force or overtighten the bulb

This is a replacement mounting screw used to secure components on compatible Frigidaire appliances. It restores proper fit and prevents loose panels or parts from rattling or shifting during operation. What it does:

• Secures panels, brackets, or small appliance parts to maintain proper alignment
• Prevents vibration-related noise caused by loose fasteners
• Replaces lost or stripped screws to restore safe, stable assembly
• Simple hardware replacement to keep appliance components secure

• One replacement mounting screw

• Power off and unplug the appliance before servicing to avoid shock or injury
• Use the proper screwdriver and align parts before tightening; do not overtighten
• Replace only the exact fastener specified by the manufacturer for that location
• If threads are damaged, inspect the mating part and repair or replace as needed

This door hinge replaces a worn or damaged refrigerator hinge to restore proper door alignment and smooth opening. It helps doors close securely and prevents sagging or rubbing that can lead to poor sealing or noise. What it does

• Supports the refrigerator door and lets it pivot smoothly on its track
• Restores correct door alignment to improve sealing and cooling efficiency
• Stops door sagging, binding, or uneven gaps
• Reduces squeaks, grinding, or other hinge noises when opening/closing

• Disconnect power and remove stored items from the door before starting
• Support the door while removing and installing the hinge to prevent drops or injury
• Tighten mounting fasteners securely but avoid over-torquing to prevent damage

This thermistor kit replaces the temperature-sensing element that communicates with the control system. Restores accurate temperature readings so your appliance can regulate cooling and defrost cycles and maintain steady, reliable performance. What it does:

• Monitors air or coil temperature and sends signals to the control board
• Helps manage compressor, fan, and defrost heater operation
• Failure can cause temperatures too warm or too cold, extended run time, or short-cycling
• Contribute to frost/ice buildup, poor cooling, or error codes/alarms

• 1 thermistor kit

• Unplug the appliance or disconnect power before servicing
• Access the sensor (commonly in an air channel or clipped to evaporator tubing)
• Match connector orientation and route wiring as original; install the sensor in the same position for accurate readings
• Restore power and allow up to 24 hours for temperatures to stabilize; run diagnostics if available to verify sensor operation

This shaft is a direct-replacement support pin that restores proper alignment and rotation in compatible Frigidaire appliances. It helps return worn or damaged supports to factory fit so components turn smoothly. What it does

• Supports and aligns a rotating component so it turns true and without excessive wobble
• Transfers rotational force from the motor/drive to the drum or rotor
• Common symptom: loud noise or scraping during operation
• Common symptom: drum or component feels loose or wobbly when spun by hand

• Disconnect power before starting any repair.
• Access may require removing panels or the appliance drum; keep track of fasteners.
• Inspect mating bearings, bushings, and seals; replace if worn to prevent premature wear of the new shaft.

This adjustable leveling foot replaces a worn or damaged refrigerator leg to stabilize and level the appliance for proper door alignment and even cooling. It helps restore a steady, wobble-free base and maintains safe operation. What it does

• Supports and levels the fridge to prevent rocking or uneven doors.
• Lets you adjust appliance height to align doors and improve seal.
• Helps correct tilting that can cause drainage or cooling issues.
• Restores a solid contact point between the appliance and the floor.

• Typically installs at the cabinet base or corner; verify correct location before tightening.
• Use basic hand tools; adjust height gradually while checking level.
• Disconnect power only if working near electrical components; otherwise no electrical disconnection required.
• Wear gloves to protect hands and avoid pinch points when lifting or supporting the appliance.

This replacement roller is a small support wheel that helps appliance doors or drawers move smoothly and stay aligned. It restores quiet, steady operation and reduces sticking or uneven travel when worn rollers cause binding. What it does

• Replaces a worn support wheel to restore smooth sliding or rolling motion
• Helps maintain proper door/drawer alignment and prevents scraping
• Reduces noise and sticking caused by cracked or flattened rollers
• Supports weight transfer so moving parts operate evenly

• One replacement roller

• Power off and unplug the appliance before starting any repair
• Access may require removing a kick plate, drawer, or door—keep fasteners organized
• Inspect adjacent tracks or mounts and replace any damaged clips or screws

This electronic control board manages the appliance's core functions and user controls so the unit operates reliably. Replacing a failed board restores normal control, timing and response for the appliance. What it does

• Receives input from buttons/sensors and sends signals to run motors, valves and lights
• Regulates timed cycles and control logic for proper operation
• Can stop certain functions from running if relays or circuits on the board fail

• Always disconnect power before accessing or replacing the control board
• Handle the board by its edges and avoid static discharge; wear an ESD strap if available
• Verify connector locations and mounting match your appliance before installing

The Electronic Control Board is an OEM part for Frigidaire refrigerators. It is responsible for the main electronic control functions of the refrigerator including monitoring temperatures, operating cooling systems, and controlling user interface features like the display panel. 

Causes of a bad control-electrical can include liquid spills inside the refrigerator that damage circuitry. Over time, electronic components may fail or degrade in performance due to regular wear and use.

Symptoms of a bad Electronic Control Board include:

• Erratic or improper cooling by the refrigerator and freezer compartments  
• Faulty or unresponsive control panels and displays
• Buzzing or clicking noises emanating from the electronic control area
• Complete failure to power on or recognition of controls

This OEM replacement is compatible with Electrolux, Gibson, Kelvinator, and Kenmore models. 

This electronic PC board is the appliance's central circuit board that manages core functions. Replacing a failed board restores proper control response and power to components so the unit starts, runs, and completes operations reliably.

• Interprets inputs from sensors and user controls to manage timing and operations
• Sends power to motors, valves, heaters, fans, or other loads as programmed
• Helps resolve symptoms like no power to controls, won't start, dead or unresponsive controls, or intermittent operation
• Addresses random stopping, error beeps/codes, or erratic component power

• Disconnect electrical power (and gas supply, if applicable) before servicing
• Handle the PCB by the edges and use anti-static protection
• Photograph/label connectors; move over any model-specific jumpers or mounting hardware from the original board
• Seat all connectors fully, secure the board, restore power, and test per your model's tech sheet

This replacement cover restores the outer trim that protects internal components and improves the appliance's appearance. It replaces a cracked, warped, or missing cover so the unit looks finished and sealed. What it does:

• Protects internal controls and wiring from dust, debris, and incidental contact
• Restores the appliance's finished appearance when the original cover is damaged or discolored
• Helps maintain a proper seal and prevents drafts around the area it covers
• Prevents rattling or vibration noise caused by a loose or broken cover

• Disconnect power before beginning any repair to avoid shock or injury
• Basic hand tools (screwdriver, nut driver) are typically required to remove fasteners
• Keep original screws and clips; confirm orientation and fit before final tightening
• If the cover is brittle or fused, work slowly to avoid breaking mounting tabs

Color: Black/natural. Nylon

This wiring harness supplies and routes electrical connections between the appliance's controls and components to restore reliable power and signal paths. It replaces a damaged or worn harness to help return normal operation. What it does:

• Provides secure electrical and signal connections between control board, motors, and sensors
• Replaces frayed, burnt, or broken wiring that can cause intermittent operation or component failure
• Helps eliminate loose-connector symptoms such as flickering lights, non-working controls, or no-start conditions
• Restores factory routing and connector fit for proper function and safety

• Disconnect power (unplug or shut off breaker) before starting any work
• Compare connectors and routing to the original harness to ensure correct fit before fastening
• Avoid pinching or pulling wires; secure harness with existing clips and fasteners