Parts for Ge DPSQ475GT0AA: 04 - Cabinet Parts

Replacement screw for securing dryer components like drum supports, panels, and housings. Needed when screws are lost, stripped, or damaged during repair.

E-coat

This adjustable gray foot supports and levels your dryer, allowing you to compensate for uneven floors. It screws into the dryer's base and can be raised or lowered to ensure the appliance sits level and stable. Replace this part if your dryer rocks, vibrates excessively, or appears tilted.

Speed nut fastener for dryers. Secures panels, covers, and internal components. Replace when stripped, missing, or damaged to restore proper assembly.

Replacement screw that secures dryer panels, trims, and internal components. Needed when original fasteners are missing, stripped, or corroded.

This exterior side panel restores the refrigerator's finished look and protects internal components from dust and damage. It's a direct-replacement exterior trim piece that keeps the cabinet edges sealed and visually complete. What it does:

• Covers and protects the refrigerator's side cavity and insulation from dust and contact
• Restores the appliance's exterior appearance after dents, scratches, or missing panels
• Helps keep internal components out of reach and reduces exposure to moisture and debris
• Matches the cabinet edge profile for a clean, factory-finish look

• Disconnect power to the appliance before starting any repair
• Remove any adjacent trim or shelving to access mounting screws
• Use appropriate hand tools; panel edges may be sharp—wear gloves to protect your hands
• Retain original fasteners; verify orientation and alignment before tightening screws

This screw is a factory replacement fastener used to secure appliance panels and components. It restores lost or loose hardware so parts sit correctly and operate without rattling or movement. What it does

• Secures panels, brackets, and small components to the appliance frame
• Restores proper alignment and helps eliminate rattling or vibration
• Replaces missing or stripped fasteners that prevent parts from staying fixed
• Matches OEM fit for reliable fastening where the original screw was used

• One replacement screw

• Use the correct-size screwdriver or driver bit to avoid stripping the head
• Power off and unplug the appliance before accessing internal components
• Tighten snugly but avoid overtightening to prevent thread damage
• Keep removed hardware organized so you can install replacements in the original locations

Front bracket and leveling screw assembly.

Rear bracket and leveling screw assembly.

Seals unused dryer vent opening to prevent air leaks and lint escape. Replace when converting vent location or if damaged. Verify fit with your model.

Replaces a cracked, rusted, or disconnected exhaust duct that routes hot air from your dryer to the home vent. Restores proper airflow and venting.

This power cord assembly connects your washer to the electrical outlet and supplies power to all machine components. It includes the proper gauge wiring and safety features required for washer operation. Replace this part if the cord is damaged, frayed, or if your washer won't power on despite having electrical power at the outlet.

Replacement mounting screw for dryer panels, brackets, and components. Needed when screws are missing, stripped, or damaged during repairs or disassembly.

This hex washer-head screw secures dishwasher components like brackets, shields, and panels. Replacing a stripped or missing screw restores a tight fit and helps prevent vibration, rattling, and loose parts during operation.

• Fastens parts where a #10-16 x 1/2-inch hex washer-head screw is specified
• Secures brackets, panels, and assemblies to the tub or frame
• Helps resolve symptoms like loose panels, vibration, or rattling noises
• Restores proper hold when the original screw is stripped, missing, or damaged

• Disconnect power and shut off water to the dishwasher before servicing
• Match length and thread to the original; replace screws one at a time to maintain alignment
• Start threading by hand to avoid cross-threading; tighten snugly—do not overtighten, especially into plastic
• Verify no wires or hoses are pinched before reassembly

• Size: #10-16 x 1/2 inch
• Head: hex washer-head
• Type: AB tapping screw