Parts for Ge DPSR475GW0AA: 03 - Cabinet Parts

E-coat

Adjustable

This white cover replaces a cracked, loose, or missing trim/cover piece on your dryer to protect the underlying opening or component and restore a clean, finished look. It also helps keep dust and debris out of the cabinet. What it does:

• Conceals and protects the designated opening/component on the dryer
• Restores proper fit and finish to the cabinet or console
• Helps keep dust and debris out of internal areas
• Common signs you need this part: broken tabs, cracks, rattling, or a missing cover

• 1 white cover

• Disconnect power to the appliance before servicing
• Use care around sharp cabinet edges; wear cut-resistant gloves
• Note orientation, remove old cover, and transfer any reusable clips/grommets if present
• Reuse existing fasteners and avoid overtightening to prevent cracking

This replacement screw secures panels, trims, and internal components to restore a snug, rattle-free fit and reliable operation. Use it to replace missing, corroded, or stripped fasteners for safe appliance performance. What it does:

• Fastens cabinet panels, trim pieces, and internal brackets to keep parts aligned and secure
• Replaces missing or damaged screws that cause loose or vibrating panels
• Prevents movement that can lead to wear, noise, or improper sealing
• Matches the original fastener role for appliances that specify part WE2M160

• Disconnect power or unplug the appliance before attempting any repair
• Use the correct screwdriver or driver bit to avoid stripping the head
• Install until snug; avoid overtightening which can strip threads or crack plastic
• If threads are damaged or fastener holes are worn, replace damaged components.

Color: White

This exterior side panel restores the refrigerator's finished look and protects internal components from dust and damage. It's a direct-replacement exterior trim piece that keeps the cabinet edges sealed and visually complete. What it does:

• Covers and protects the refrigerator's side cavity and insulation from dust and contact
• Restores the appliance's exterior appearance after dents, scratches, or missing panels
• Helps keep internal components out of reach and reduces exposure to moisture and debris
• Matches the cabinet edge profile for a clean, factory-finish look

• Disconnect power to the appliance before starting any repair
• Remove any adjacent trim or shelving to access mounting screws
• Use appropriate hand tools; panel edges may be sharp—wear gloves to protect your hands
• Retain original fasteners; verify orientation and alignment before tightening screws

This screw is a factory replacement fastener used to secure appliance panels and components. It restores lost or loose hardware so parts sit correctly and operate without rattling or movement. What it does

• Secures panels, brackets, and small components to the appliance frame
• Restores proper alignment and helps eliminate rattling or vibration
• Replaces missing or stripped fasteners that prevent parts from staying fixed
• Matches OEM fit for reliable fastening where the original screw was used

• One replacement screw

• Use the correct-size screwdriver or driver bit to avoid stripping the head
• Power off and unplug the appliance before accessing internal components
• Tighten snugly but avoid overtightening to prevent thread damage
• Keep removed hardware organized so you can install replacements in the original locations

Front bracket and leveling screw assembly.

Rear bracket and leveling screw assembly.

This exhaust cover plate seals an unused dryer vent opening on the cabinet to prevent air leaks and lint escape. Replacing a missing or damaged cover helps maintain proper airflow and support efficient drying performance. What it does:

• Covers and seals an unused exhaust port on the dryer cabinet
• Helps maintain correct airflow through the exhaust duct
• Helps keep lint and warm, moist air from leaking into the laundry area
• Replace if the original is missing, cracked, loose, or you notice lint/air leakage or longer dry times

• 1 exhaust cover plate

• Disconnect power; for gas dryers, turn off the gas supply
• Locate the unused exhaust opening (rear, side, or bottom—depending on vent configuration)
• Position the plate over the opening and secure using the existing hardware; do not overtighten
• Restore power and verify proper airflow at the active vent

This exhaust duct routes hot, moist air from the appliance to the home vent, helping maintain proper airflow and reduce lint buildup. It's a direct-fit replacement designed to restore correct venting and appliance performance. What it does:

• Channels exhaust air from the appliance to the external vent.
• Helps prevent reduced airflow that can lengthen cycle times or reduce drying/heating performance.
• Reduces lint accumulation in the appliance exhaust path when intact and properly connected.
• Replaces damaged, crushed or disconnected ducting that can cause air leakage or poor venting.

• Disconnect power to the appliance (and shut off gas supply for gas models) before starting.
• Use gloves to avoid sharp edges; secure connections with the original clamps or equivalent fasteners.

Gas dryer application

A replacement screw used to secure panels and components in compatible GE appliances. Replacing missing or damaged screws restores secure mounting, reduces rattling, and helps keep parts aligned during normal operation. What it does:

• Fastens panels, trim, brackets, or small appliance components to maintain proper alignment and fit.
• Keeps internal parts secured to reduce vibration, rattling, or movement during use.
• Replaces stripped, rusted, or missing hardware that can cause loose or misaligned panels.
• Small, non-electrical part — does not affect electrical circuits or controls.

• Disconnect power and unplug the appliance before accessing internal parts.
• Use the properly sized screwdriver to avoid stripping the head; hand-start threads to prevent cross-threading.
• Tighten securely but avoid over-torquing; overtightening can strip threads or damage plastic components.
• Keep track of small parts and hardware; replace any damaged or mismatched screws with the correct OEM part.