Parts for Ge GLE12HSPARSS: Cabinet Parts

This harness cover is a molded protective shroud that shields and organizes the appliance wiring harness, helping prevent abrasion and accidental contact for safer, more reliable appliance operation. What it does:

• Protects wiring harness from rubbing, pinching, and physical damage
• Keeps wires neatly routed to reduce strain and accidental disconnection
• Helps reduce risk of shorting or arcing from exposed wiring
• Resolve symptoms like intermittent electrical issues or visible wire wear when the original cover is broken or missing

• Disconnect power to the appliance before starting any work.
• Remove access panels as needed to reach the wiring harness; replace the cover so clips or tabs fully engage.
• Do not alter or cut the cover; inspect wiring for damage and repair any frayed wires before reinstalling.

A small machine screw used to fasten appliance components where an M5 x 16 metric screw is required. Durable metal construction provides a secure fit for panels, brackets and assemblies that use a metric M5 thread. What it does

• Secures panels, brackets or small assemblies that accept an M5 x 16 machine screw
• Replaces stripped or missing fasteners to restore proper fit and alignment
• Helps prevent vibration and rattling when the correct screw is used
• Commonly used in appliances with metric hardware fastenings

• One M5 x 16 screw

• Verify size (M5 x 16) and thread type before installing to ensure proper fit
• Use the correct driver and moderate torque to avoid stripping the head or threads
• Disconnect power and follow appliance safety guidelines before servicing
• If screw threads are damaged, replace with the correct-size fastener rather than reusing

This upper freezer mullion gasket seals the gap between freezer doors and the cabinet to help maintain cold temperatures and reduce frost. It replaces a worn or damaged upper door mullion seal to improve door contact and energy efficiency. What it does:

• Forms a weather-resistant seal along the upper door mullion to limit cold air loss
• Helps reduce frost build-up and cycling caused by a poor door seal
• Improves freezer temperature stability and can reduce run time from air leakage
• Common symptom: visible gaps, torn or flattened gasket, or frost forming between doors

• One upper freezer mullion gasket

• High-level swap: remove the old mullion gasket, clean mounting surface, and press the new gasket into place
• Use gentle heat (manufacturer guidance) only if needed to make the gasket pliable; avoid open flames
• Unplug or disconnect power to the appliance before working on door parts for safety
• If adhesive or clips are present, replace only with manufacturer-recommended materials

This fresh food air return duct cover directs cold air back into the refrigerator compartment and helps maintain proper airflow and temperature distribution. It replaces damaged or missing covers to restore consistent cooling and reduce cold-spot issues. What it does

• Channels return airflow from the fresh food section to the evaporator/fan area for balanced cooling.
• Prevents items from blocking the air intake and helps maintain even temperature distribution.
• Reduces abnormal fan noise caused by loose or broken ducting.
• Commonly replaced when cracked, broken, missing, or warped causing poor cooling or uneven temperatures.

• One fresh food air return duct cover

• Disconnect power before servicing the refrigerator to avoid electrical hazards.
• Usually installs with snap tabs or a few screws; shelf removal may be required for access.
• Handle plastic parts carefully to avoid cracking during installation.

This screw secures the refrigerator air tower/air duct components, keeping the airflow assembly and covers properly fastened for consistent cooling performance. Durable metal construction designed for a direct replacement. What it does:

• Fastens the air tower/air duct to the cabinet or evaporator housing
• Keeps air-guiding components aligned to maintain proper airflow
• Prevents covers or ducts from vibrating or coming loose
• Resolves rattling noises or loose ducting near the evaporator area

• One screw

• Use the correct screw size and thread to avoid stripping the mounting hole
• Tighten until snug; do not overtighten to prevent damage to plastic parts
• Disconnect power to the appliance before working near the evaporator or fan area

Supports and aligns the middle section of your refrigerator door. Replace if hinge is cracked, broken, or causing door misalignment and uneven gaps.

Conceals and protects the left refrigerator door hinge. Replace if cracked, broken, or missing to restore a clean, finished look and keep debris out.

Refrigerator front cap insert that covers exposed edges or gaps on the cabinet front. Replace if the original cap is cracked, broken, or missing.

This molded hinge cover replaces the damaged or missing right-side top hinge trim on compatible refrigerators, restoring a finished appearance and protecting the hinge from dust and debris. Fits the top right hinge area. What it does:

• Covers and protects the top right door hinge from dirt and damage.
• Restores the cabinet's finished look when the original cover is cracked or missing.
• Prevents debris from interfering with hinge movement that can cause noise or uneven door alignment.
• Helps keep the hinge area safer to touch by covering sharp edges.

• One right hand top hinge cover

• Unplug the refrigerator and remove food from the door area before starting.
• Support the door while removing the top hinge to prevent it from dropping.
• Install with basic hand tools; avoid over-tightening fasteners to prevent cracking the cover.
• Wear gloves and eye protection and follow the appliance manufacturer's service instructions.

This is a self-tapping ST3.5 x 9.5 screw used to secure panels, trim and small appliance components. It replaces missing or damaged screws to restore proper fit and prevent rattling or loose parts. What it does:

• Fastens control panels, brackets, trim pieces and light assemblies
• Replaces stripped, corroded or missing screws that allow parts to shift
• Restores secure mounting and helps eliminate vibration noise
• Small size for low-profile applications where a compact fastener is required

• Use the correct sized Phillips or Pozidriv driver to avoid cam-out
• Start screws straight and drive until snug; avoid overtightening to prevent stripping
• Disconnect power and remove any sharp panels before working to stay safe
• Keep a small parts tray to avoid losing tiny screws during repair

Secures the refrigerator door and provides smooth pivot action. Replace if your door sags, won't close properly, or seal is compromised. Verify fit with your model.

Plastic hinge cap insert installs on refrigerator door hinge to cover hardware and provide finished look. Replace if cracked, broken, or missing.

White plug button for bottom-mount refrigerators. Covers and conceals mounting holes or unused openings. Replace when cracked, broken, or missing.

Secures and aligns your refrigerator door for smooth opening and proper sealing. Replace when door sags or alignment issues occur. Verify fit with your model.

This freezer mullion lower gasket seals the bottom of the freezer door mullion to help keep cold air inside and reduce frost buildup. It restores a tight door seal for better temperature control and energy efficiency. What it does:

• Replaces a worn or torn lower mullion gasket that lets warm air enter the freezer
• Helps stop frost and ice buildup between the freezer doors and mullion
• Reduces air leakage that can cause the freezer to run more often
• Restores proper door sealing for consistent freezer temperatures

• One lower mullion gasket

• Disconnect power or unplug the appliance before beginning work
• Remove old gasket and clean mounting surface of debris and adhesive residue
• Press new gasket into place, ensuring it seats evenly along the mullion
• After installation, check door closure and trim or reseat gasket where needed for a uniform seal

Refrigerator connecting pipe links components in the cooling system. Replace if cracked, leaking, corroded, or damaged to restore proper refrigerant flow.

This sealed component removes moisture and contaminants from the R600 refrigerant system, typically located in the sealed system behind the refrigerator. Replace if the refrigerator isn't cooling properly, runs constantly, or if a technician identifies refrigerant system contamination.

This rubber compressor grommet cushions and isolates the compressor to reduce vibration and noise while protecting mounting points from wear. It fits between the compressor and the chassis for quieter, more reliable operation. What it does

• Absorbs vibration from the compressor to help reduce humming and rattling noises
• Cushions the compressor to prevent metal-to-metal contact and wear on mounting points
• Helps maintain proper compressor alignment for consistent performance
• Commonly replaced when mounts are cracked, compressed, or missing

• One compressor grommet

• Disconnect power to the appliance before performing any service
• Access may require tilting or raising the appliance and removing the lower access panel
• Replace any additional worn mounts for balanced support; inspect nearby hardware and mounts

This compressor clip secures the refrigerator compressor to its mounting bracket, helping reduce vibration and movement for quieter, more reliable operation. A simple replacement that restores proper compressor seating and alignment. What it does:

• Secures the compressor to its mount to prevent excess movement and vibration
• Helps reduce rattling or buzzing noises caused by a loose compressor
• Keeps compressor aligned to avoid strain on refrigerant lines and wiring
• Supports stable operation after compressor service or during reassembly

• Disconnect power to the appliance before beginning any work
• Support the compressor or mounting bracket while removing and installing the clip
• Use basic hand tools; avoid bending refrigerant lines or tugging wiring

This M4 x 8 mm machine screw secures small panels and components on compatible appliances, restoring proper fit and preventing rattles or loose parts. Compact, corrosion-resistant fastener for routine repairs. What it does

• Fastens trim, control panels, brackets, or small assemblies where an M4 x 8 screw is specified
• Restores secure mounting to stop vibrations, rattling, or misaligned panels
• Replaces missing or stripped screws that prevent proper part installation
• Small size for confined spaces and precision fastening

• One M4 x 8 mm machine screw

• Use the correctly sized Phillips or hex driver to avoid cam-out or head damage
• Turn off and unplug the appliance before accessing internal parts
• Hand-start the screw to avoid cross-threading; do not overtighten to prevent stripping

Fix refrigerator not cooling or running constantly with this inverter compressor drive module. Restores variable-speed control for stable temperatures.

Refrigerator not cooling evenly or fresh food section too warm? This fresh food air tower directs cold air from freezer to fridge. Moderate DIY repair.

This Fresh Food Air Tower Gasket seals the fresh-food compartment air tower to help direct airflow and maintain even temperatures inside the refrigerator. It replaces a worn or damaged seal to reduce air leaks and improve cooling consistency. What it does:

• Creates an air-tight seal around the fresh-food air tower to help control airflow between compartments
• Helps prevent cold air loss that can cause uneven cooling or frost build-up
• Restores proper air circulation after gasket damage, tears, or deformation
• Fits into the air tower/baffle area and works with the refrigerator's existing airflow components

• One fresh food air tower gasket

• Inspect the air tower and surrounding area; remove old gasket and clean mating surfaces before installing new gasket
• Press the gasket into the channel evenly; avoid stretching or twisting the seal during install
• Use basic hand tools; no special calibration required after replacement
• Unplug the appliance or turn off power before servicing to reduce shock risk

Fresh food not cooling properly? The thermistor monitors compartment temperature for accurate cooling. Test resistance against specs to diagnose.

Fix inconsistent cooling or incorrect temperature readings in your refrigerator's fresh food section with this lower thermistor. Moderate DIY repair.

This is a single ST3.9 x 16 appliance screw used to secure panels, trim and small components. It replaces a lost or damaged fastener so parts stay aligned and appliances operate quietly and safely. What it does

• Fastens small sheet-metal and plastic appliance components.
• Holds control panels, trim, brackets or insulation in place.
• Prevents rattling, misalignment or loose panels caused by missing or worn screws.
• Matches OEM thread size and length for correct fit where specified.

• Use the correct driver and match thread engagement to avoid stripping.
• Start threads carefully and do not overtighten; stop when snug.
• Disconnect power before working on electrical components or panels where wiring is present.
• If replacing multiple fasteners, use the same thread type and length for consistent fit.

This thermistor is the freezer compartment temperature sensor that monitors cold-air temperature and helps the control board maintain proper cooling. Replace a faulty sensor to restore correct temperature readings and more consistent freezer performance. What it does:

• Detects freezer air temperature and sends a signal to the control board
• Helps regulate compressor and fan cycles for steady cooling
• Commonly linked to symptoms like freezer running too warm, inconsistent temperatures, or incorrect temperature readouts
• Can cause frequent on/off cycling or frost buildup when it fails

• One freezer thermistor sensor (1 pack)

• Disconnect power to the appliance before starting any repair
• Handle the sensor and wiring harness gently to avoid damage to the probe or connector
• The sensor typically mounts inside the freezer near the evaporator; follow OEM service instructions for exact location and routing
• Test the sensor with a multimeter per OEM resistance-to-temperature specifications

This freezer transition gasket replaces the worn or torn seal that closes the gap between freezer sections to help maintain proper temperature and reduce frost buildup. Restores a tighter door seal for more efficient cooling. What it does:

• Replaces a damaged transition gasket to reduce air leaks and help prevent frost accumulation
• Helps maintain consistent freezer temperatures by sealing the joint between freezer sections
• Can improve energy efficiency when the original seal is cracked, split, or misshapen
• Common symptom: visible gaps, drafts, or frost forming along the freezer transition area

• Remove the old gasket and clean the mounting surface before installing the new gasket
• Installation typically requires basic hand tools; follow your model's service instructions
• Do not force the gasket into place; ensure correct orientation and a snug fit around the transition area

Fix a refrigerator that won't power on with a new power cord. Restores electrical connection when the original cord is damaged, worn, or frayed.

A Y-head screw replacement fastener for securing appliance components where a Y-shaped drive is required. Restores proper fastening when original screws are stripped, missing, or damaged. What it does:

• Replaces a damaged or missing Y-head screw used to secure panels, brackets, or components.
• Provides correct Y-shaped drive engagement for tamper-resistant or OEM-specific fasteners.
• Helps stop rattling, loose parts, or misaligned panels caused by missing or stripped screws.
• Use when original screw drive prevents standard screwdriver engagement.

• Use the matching Y-head driver bit; do not force with incorrect tools to avoid damage.
• Tighten until snug; avoid over-torquing which can strip threads or crack plastic parts.
• Disconnect power and follow appliance safety instructions before servicing any electrical components.
• Replace all matching screws to maintain even fit and alignment.

Fix unresponsive controls or system malfunctions with this refrigerator main control board. Restores proper coordination of all appliance functions.

Fix cooling issues in your refrigerator with this process valve. Regulates refrigerant flow for proper temperature control. Red cap design for R600 systems.