Parts for Ge TBT18DAXBRAA: 03 - Cabinet Parts

This rear wheel roller replaces a worn or damaged drawer/glide wheel to restore smooth movement and reduce sticking or noise. Durable molded construction fits the rear guide position to help support and steady the sliding drawer or bin. What it does

• Supports and guides the appliance drawer or bin for smooth in-and-out motion
• Replaces cracked, chipped, or worn rear wheel that causes binding or catching
• Helps reduce squeaks and uneven movement from a damaged roller
• Restores proper alignment and load support at the rear glide point

• One rear wheel (roller)

• Disconnect power and remove the drawer/bin per your owner's manual before replacing the wheel
• Typically installs by snapping or sliding into the rear glide bracket; basic hand tools may be needed
• Inspect mating tracks or brackets for damage and clean debris before installing the new wheel

Refrigerator plug button that installs in the cabinet or liner. Replace this insert if the original is cracked, broken, missing, or worn from use.

A small replacement shim that fits at the center hinge to correct hinge alignment and keep the door operating smoothly. Helps reduce binding and uneven gaps so the door closes more reliably. What it does:

• Provides a precise spacer at the center hinge to correct misalignment
• Helps reduce door rubbing, binding, and uneven wear on hinge surfaces
• Restores proper door fit and helps maintain an even gasket seal
• Used during hinge adjustment or after hinge/door repair to fine-tune alignment

• Follow the appliance manufacturer's service manual; disconnect power or water if required before starting
• Remove the door or hinge trim as needed to access the center hinge per instructions
• Reinstall hinge hardware in the same order; tighten fasteners evenly and test door movement

Almond-colored center hinge for refrigerator doors. Replaces worn, cracked, or broken hinges that cause door misalignment or gaps between compartments.

Corner cap for refrigerator exterior trim. Replaces cracked, broken, or missing caps on cabinet corners. Restores finished appearance and protects edges.

Replace worn, missing, or damaged washers in your top-mount refrigerator. This 12-pack provides essential hardware for secure component installation.

This part has been discontinued and is no longer available.

Leveling nut for refrigerators. Threads onto adjustable front feet to stabilize and level your appliance. Replace if stripped, cracked, or missing.

Plastic plug button insert for refrigerator shelves and interior panels. Replaces missing, cracked, or broken plug inserts that leave exposed holes.

Mounting screw for refrigerator interior components and panels. Replace if lost, stripped, or damaged during maintenance. Essential hardware for secure assembly.

Mounting bracket that secures the evaporator fan motor in place. Replace if cracked, bent, or broken to properly support the fan motor assembly.

Fix a refrigerator that's not cooling properly or making noise with this evaporator fan blade. Direct replacement part restores proper airflow.

Freezer not cooling or making buzzing noise? The evaporator fan blade circulates cold air. Easy DIY fix in under 5 minutes—simply pull off and press on.

The Fan Blade Grommet is an OEM replacement part for GE brand refrigerators. Located behind the evaporator fan blade where its central shaft passes through, this rubber sealing piece creates a protective barrier isolating the fan assembly.

Causes of a potentially problematic fan blade grommet include cracks or deterioration that develop from continuous vibration and impacts over extended use. Exposure to temperature fluctuations can also cause the rubber to harden and lose elasticity. 

Symptoms of a faulty fan blade grommet include:

• Airflow obstructions within the duct 
• Noisy vibrations from the fan assembly
• Rubber debris collecting on components

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore model refrigerators.

Size: 10-16 ab.

8-18 CA HX 1/2 S

Replacement mounting screw for securing panels, trim, and internal brackets. Needed when original fasteners are missing, stripped, or damaged.

This pack contains twelve replacement screws used to fasten appliance panels, trim, and components. They restore secure mounting and help stop rattling, loose panels, and gaps for a safer, quieter appliance. What it does:

• Secures exterior and interior panels, brackets, and trim pieces
• Restores proper fit where missing or stripped screws cause movement or noise
• Helps maintain appliance alignment and prevents parts from vibrating loose
• Used for general-purpose repairs on compatible GE appliances

• Disconnect power or unplug the appliance before performing any internal repairs
• Use the correct screwdriver bit and avoid overtightening to prevent stripping threads
• Keep remaining screws in a labeled container for future service
• If a screw does not seat easily, stop and verify correct fit to avoid damage